VEVOR C110 TPMS RV Tire Pressure Monitoring System

Enfòmasyon sou pwodwi

Espesifikasyon

• Modèl: C110
• Voltage: DC 12V
• Pouvwa: 0.03W
• Test The Tire Pressure Range (Bar): 0.5-6
• Pwa nèt: 0.1 Kg

Enstriksyon Itilizasyon Pwodwi

Karakteristik

1. Monitor the pressure and temperature of your tyres
2. Mòd dòmi entèlijan pou ekonomize pouvwa

Estrikti

The product consists of a wrench, nut, sensor, and host.

Parameter Setting Reference

1. Before using the product, charge the display for 3-4 hours with the cigarette plug charger.
2. Anviwònman paramèt default faktori:
   • Hl pressure alarm data: 3.0 Bar (0.6-6.0 Bar range)
   • Low-pressure alarm data: 2.0 Bar (0.5-5.9 Bar range)
   • Hl temperature alarm data: 68 (ranje 50-99)
   • Nòt: 1 Bar = 14.5 Psi

Enstriksyon Operasyon

1. When the ACC is ON, the display will enter self-test mode for 2 seconds.
2. When the speed reaches 20 kilometers per hour, the sensor will activate and start detecting and sending pressure and temperature data.
3. Alarming instructions:
   • a) Over-pressure or leakage will trigger a warning.
   • b) High temperature will trigger an alarm with corresponding icons and sounds.
   • c) A low sensor battery will trigger a warning with icons and sounds.

ENTWODIKSYON

• Nou kontinye pran angajman pou ba ou zouti pri konpetitif.
• "Ekonomize Mwatye", "Mwatye Pri" oswa nenpòt lòt ekspresyon menm jan an nou itilize sèlman reprezante yon estimasyon ekonomi ou ta ka benefisye lè w achte sèten zouti avèk nou konpare ak pi gwo mak yo, epi yo pa nesesèman vle di kouvri tout kategori zouti nou ofri yo. Nou tanpri raple w pou w verifye ak anpil atansyon lè w ap pase yon lòd avèk nou, si w ap reyèlman ekonomize mwatye an konparezon ak pi gwo mak yo.
• Sa a se enstriksyon orijinal la. Tanpri li tout enstriksyon manyèl la ak anpil atansyon anvan ou itilize li. VEVOR rezève yon entèpretasyon klè pou manyèl itilizatè nou an.
• Aparans pwodwi a ap depann de pwodwi ou te resevwa a. Tanpri eskize nou pou nou pa fè w konnen ankò si gen nenpòt mizajou teknolojik oswa lojisyèl sou pwodwi nou an.

LIS PARAMÈT

Modèl	C110
Voltage	DC 12V
Pouvwa	0.03W
Test The Tire Pressure Range (Bar)	0.5-6
Pwa nèt (Kg)	0.1

LIS PATI

OPERASYON

Karakteristik

1. Monitor the pressure and temperature of your tyres
2. Mòd dòmi entèlijan pou ekonomize pouvwa
3. Tyre leaking warning
4. Visual and audible warning for abnormal tyre pressure and temperature
5. Displays up to 4 tyre temperatures and pressures at a glance
6. Can be set to Fixed Bar or PSI
7. Can be set to °C or °F temperature

Estrikti

1. Inite presyon
2. Inite tanperati
3. Done presyon
4. Done tanperati
5. Sensor battery indicator
6. Siy avètisman
7. Antre voltage
8. SET”Button
9. (+) Bouton
10. USB pò

REFERANS PARAMET SETTING

1. Before using this product, please press any button on the display to turn it on, and charge the display for 3-4 hours with the cigarette plug charger.
2. Anviwònman paramèt default faktori
   

   Anviwònman default faktori	Paramèt seri ranje
   Hl pressure alarm data: 3.0Bar	0.6-6.0 Bar
   low-pressure alarm data:2.0Bar	0.5-5.9 Bar
   Hl temperature alarm data: 68℃	50-99 ℃

3. 1Bar=14.5Psi

ENSTRIKSYON OPERASYON

1. When the ACC is ON, the display will get into self-test mode for 2 seconds. After 2 seconds, all icons will be displayed on the LCD screen and ready to receive the new data. When the ACC is OFF, the display will be OFF.
2. When the speed is up to 20 kilometers per hour, the sensor will be activated, and start to detect and send the Pressure and temperature data.
3. Alarming instruction
   • a) When tyre pressure is over the set range or the tyre is leaking, the corresponding tyre position icon, pressure data, and the alarm icon (!) will flash together, and the built-in buzzer will chirp as: Bi Bi ·.
   • Nòt: Press any button can stop the buzzer, but all corresponding icons still flash, buzzer will chirp once per minute.
   • b) When tyre temperature is over the set data, the according tyre position icontemperature data, and high temperature alarm icon (!) will flash together, and the built-in buzzer will chirp as: Bi Bi.
   • c) When the sensor battery is low, the icon * of the corresponding tyre position, the sensor’s low battery icon will flash together, and the built-in buzzer will chirp as: Bi Bi.
   • Nòt: To stop the buzzer, press the set buzzer.
   • Nòt: all icons will still flash, buzzer will “Chirp” once per minute.

ETAI ALAM

Leaking or low tyre pressure alarm

• Pa egzanp: L.R. tyre leaking or low tyre pressure alarm. The corresponding tyre position icon, pressure data, and the alarm icon (!) will flash together.

High tyre pressure alarm

• Mete seri: 1.7~3. 4Bar Pa egzanp: L.R. tyre high-pressure alarm. The corresponding tyre position icon , pressure data, and the alarm icons (!) will flash together.

High tyre temperature alarm

• Anviwònman default faktori: 70°C. E.g.: L. R. tyre high temperature alarm. Temperature data and high high-temperature alarm icon (!) will flash together.

Capteur ki ba batri

• Sensor battery normal life: 3-5 years. E.g.: L.R. Tyre high temperature alarm. The tyre position icon sensor low battery icon pral flache ansanm.

Sensor not work

• Pa egzanp: L.R. tire sensor does not work for the corresponding tyre position icon , pressure data, and the temperature will disappear together

WORK PARAMETER SETTING OPERATION

1. Antre epi kite mòd anviwònman:
   • Press the “ SET ” button and hold on for 3 seconds, release the button after hearing 1 long chirp, the monitoring system will enter the setting mode. Press the “ SET ” button short time to recycle among the following settings: Bar-Psi, C >F, pressure Hl, pressure LO, alarm temperature HI. Press the (+) button to adjust the corresponding data. After finishing all settings, press the “ SET ” button and hold on for 3 seconds.
   • After hearing l short chirp, the system saves all set parameters and quits the setting mode.
   • (Remak: After entering the setting mode, if there is no operation within 3 minutes, the system will quit the mode and back to normal working mode automatically)
2. Tyre pressure HI setting:
   • Press and hold the “ SET ” button for 3 seconds, release the button after hearing 1 long chirp, will enter the setting mode.
   • Then press the (+) button one by one to get into tyre pressure HI setting mode. The pressure HI data flash, press the (+) button to adjust the data, then press the “ SET ” button and hold on for 3 seconds, release the button after hearing a short chirp, the system saves the set data and quit the mode.
   • (Remak: the set pressure HI data must be higher than the set pressure LO data. Pressure HI adjustable range: 0.6-6.0 Bar. Factory default setting: 3.0Bar)
3. Tyre pressure LO setting: Press and hold on the (+) button for 3 seconds.
   • Release the button after hearing a long chirp; the system enters the setting mode. Then press the “ SET ” button one by one to enter into tyre pressure LO setting status. The pressure LO data will flash press the (+) button to adjust the data, then press the “ SET ” button and hold for 3 seconds, release the button after hearing l short chirp, the system saves the set data and quit the mode.
   • (Remak: the set pressure LO data must be lower than the set pressure HI data. Pressure LO adjustable range: 0.5-5.9 Bar, Factory default setting: 2.0Bar)
4. Release the button after hearing the long chirp, and the system enters the setting mode.
   • Then press the (+) button one by one to get into alarm temperature HI setting status, the icon will flash, press the RIGHT button to adjust the data, then press the button and hold on for 3 seconds, release the button after hearing l short chirp, the system saves the set data and quit the mode.
   • (Remak: temperature HI adjustable range: 50 ℃ – 99 ℃ Factory default setting: 68 ℃ )
5. Anviwònman inite presyon: Press and hold on the (+) button for 3 seconds, release the button after hearing a long chirp. The system enters pressure unit setting mode. The Bar icon will flash, press the (+) button to adjust the unit, then press the set button and hold on for 3 seconds, release the button after hearing l short chirp, the system saves the set data and quit the mode. (Factory default setting: Bar)
6. Tanperati inite anviwònman: Press and hold the (+) button for 3 seconds, release the button after hearing a long chirp, and the system enters the setting mode. Then press the (+) button one by one to get into the temperature unit setting status. The C icon will flash. Press the button to adjust the data, then press the button and hold on for 3 seconds, release the button after hearing l short chirp, the system saves the set data and quit the mode.
7. Tyre pressure code matching Long press the (+) button for 3 seconds and release it after hearing a long “Bi” to enter the tyre pressure code matching mode, the left front wheel icon and “_.” fash press the “ SET ” button to select the tyre to be matched, and the corresponding tyre after selection “_.” will flashing, at this time, inflate the corresponding tyre (The external sensor is directly screwed to the valve), after receiving the signal “_.” changes to the pressure value to indicate that the matching is successful, then short press the (+) button to jump to the next tyre. Follow the previous step to match other tyres. After matching, press and hold the (+) button for 3 seconds, save and exit. After a “Bi” (Entering the tyre matching mode without any action, the matching mode will automatically exit after 3 minutes)
   • (Remak: The sensor and receiver have been matched before leaving the factory, and the sensor or receiver needs to be re-matched to change the sensor or receiver.)

INTERNAL SENSOR INSTALLATION

1. Jack up the car and remove the tire.
2. Remove the original valve.
3. Tighten up screw
4. Install the tire from the left side of the valve clockwise direction, avoiding the tire bead from hitting the valve and sensor.
5. Capteur Rasanble
6. Tighten the valve by wrench and screw it (Torque value must be ≥ 4Nm)
7. Balanse kawotchou a.
8. Mount the tire in its position.

Enstalasyon Capteur ekstèn

1. Devise bouchon valv la.
2. Vise nwa a.
3. Screw in the sensor.
4. Lock the sensor with an anti-theft wrench.

Movement / Replacement of battery

1. Peel off the non-slip gasket
2. Unscrew the sensor with a wrench

Enfòmasyon FCC

Aparèy sa a konfòm ak Pati 15 Règ FCC yo. Operasyon an sijè a de kondisyon sa yo.

1. Pwodui sa a ka lakòz entèferans danjere.
2. Pwodui sa a dwe aksepte nenpòt entèferans resevwa, ki gen ladan entèferans ki ka lakòz operasyon endezirab.

ATANSYON: Chanjman oswa modifikasyon pati ki responsab pou konfòmite pa apwouve ekspreseman kapab anile otorite itilizatè a pou opere ekipman an!
AVÈTISMAN: Chanjman oswa modifikasyon nan pwodwi sa a pa ekspreseman apwouve pa pati a. Responsab pou konfòmite ka anile otorite itilizatè a pou opere pwodwi a.
Nòt: Yo te teste pwodui sa a epi yo jwenn li konfòme li ak limit pou yon aparèy dijital Klas B dapre Pati 15 Règ FCC yo. Limit sa yo fèt pou bay pwoteksyon rezonab kont entèferans danjere nan yon enstalasyon rezidansyèl.
Pwodui sa a jenere, itilize, epi li ka emèt enèji frekans radyo, epi si li pa enstale epi itilize dapre enstriksyon yo, li ka lakòz entèferans danjere nan kominikasyon radyo. Sepandan, pa gen okenn garanti ke entèferans pap rive nan yon enstalasyon patikilye. Si pwodui sa a lakòz entèferans danjere nan resepsyon radyo oswa televizyon, sa ou ka detèmine lè w etenn epi limen pwodui a, nou ankouraje itilizatè a pou l eseye korije entèferans lan avèk youn oswa plis nan mezi sa yo.

• Reoryantasyon oswa deplase antèn k ap resevwa a.
• Ogmante distans ki genyen ant pwodwi a ak reseptè a.
• Konekte pwodwi a nan yon priz sou yon sikwi diferan de sa a ki reseptè a konekte.
• Konsilte konsesyonè a oswa yon teknisyen radyo/televizyon ki gen eksperyans pou asistans.

JETE KOREKTE

• Pwodui sa a sijè a dispozisyon Direktiv Ewopeyen 2012/19/EU a. Senbòl ki montre yon bwat fatra ak wou ki bare a endike ke pwodui a bezwen koleksyon fatra separe nan Inyon Ewopeyen an.
• This applies to the product and all marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling of electrical and electronic device accessories

SÈVIS KLIYAN

• Manifakti: Shanghaimuxinmuyeyouxiangongsi
• Adrès: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.
• Enpòte nan AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Ostrali
• Enpòte nan USA: Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
• YH CONSULTING LIMITED |
• C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX
• E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main.

Sètifika Garanti

• Sipò teknik ak Sètifika E-Garanti www.vevor.com/support

Kesyon yo poze souvan

How do I stop the buzzer alarm?

To stop the buzzer, press the set buzzer; please note that all icons will still flash, and the buzzer will chirp once per minute.

Dokiman / Resous

VEVOR C110 TPMS RV Tire Pressure Monitoring System [pdfManyèl Enstriksyon C110, C110 TPMS RV Tire Pressure Monitoring System, TPMS RV Tire Pressure Monitoring System, Tire Pressure Monitoring System, Pressure Monitoring System, Monitoring System

Referans

• Manyèl itilizatè