sensor switch WSRA Series Wall Switch Sensor with Occupancy

Espesifikasyon:

• Series: WSRA Series
• Operational Settings: Occupancy Time Delay, On Mode, Switch
• Modes, Darkness Set-Point, Photocell Mode, LED Operation, Manual On
• Grace Period, Predictive Exit Time, Predictive Grace Time, Fade On Rate

Occupancy Time Delay:
The occupancy sensor can be set to keep the lights on for different durations after detecting occupancy. Adjust the setting as per your preference.

On Mode:

Choose between Automatic On, Manual On, or Reduced Turn-On modes based on your requirements. Automatic On turns the lights on automatically upon occupancy detection, Manual On requires manual intervention to turn the lights on, and Reduced Turn-On initially ignores small motions.

Chanje mòd:
Switch between different modes such as Switch Disable, Predictive Mode, and Predictive Mode with Expiration. These modes control how the sensor operates after a certain period of inactivity.

Darkness Set-Point / Inhibit Set-Point:
Set the ambient light level at which the lights will be adjusted to the High Trim setting. The Set Now option automatically selects the Darkness Set-Point based on current conditions in the room.

Photocell Mode
Enable or disable the feature that prevents lights from turning on when the light level is above the Inhibit Set-Point.

Retabli Defo
Reset all functions to their original settings if needed.

Dirije operasyon
Select the behavior of the device’s LED indicator.

Manual On Grace Period
Set a grace period for manual control of the lights when in Manual On mode.

Predictive Exit Time and Predictive Grace Time
Adjust the time intervals for predictive exit and grace periods when occupants leave the room.

Fade On Rate
Set the time required for the lights to reach their preset brightness level.

Operational  settings

Occupancy Time Delay:
Longè tan yon Capteur lokatè ap kenbe limyè yo limen apre li dènye detekte lokatè.

3=On Mode
Pa aplikab ak Opsyon Pòs vid (VA).

Otomatik sou
Capteur otomatikman limen limyè yo lè li detekte lokatè.

Manyèl Sou
Capteur mande pou peze bouton an pou limen limyè yo.

Redwi Turn-On
Capteur se fikse okòmansman sèlman detekte gwo mouvman, efektivman inyore nenpòt siyal enfrawouj pasif (PIR) reflete. Okipan yo ap toujou detekte imedyatman lè yo antre nan chanm nan paske siyal PIR yo gwo. Yon fwa limyè yo sou, Capteur a retounen nan sansiblite maksimòm.

1. Otomatik sou
2. Redwi Turn-On
3. Manual On ‘

4=Switch Modes
Pa aplikab ak Opsyon Pòs vid (VA).

Chanjman aktive (anplase Off)
Button will turn lights And keep them off until pressed again. The lights will remain off until the button IS pressed again, resetting the sensor to Automatic On mode.
Chanje Enfim
Yo anpeche itilizatè a fèmen limyè yo atravè bouton pouse a.
Mòd prediksyon
Pressing the push-button switch turns the lights off and temporarily disables the occupancy detection. After 10 seconds, the occupancy detection reactivates am mmttors for an additional 30 seconds. no «upancyls detected during this period” the sensor will revert to Automatic On operation. If occupancy is detected the sensor will remain in Override Off mode and requires the switch to be pressed in order to restore the sensor to Automatic On.

Predictlve Mode wdth Expiratlon
Pressing push-button switch turns the lights off and temporarily disables the occupancy detection. After 10 s«mds, the occupancy detection reactivates am mmltors for an additional 30 seconds If no occupancy is detected during this period” the gnsor WII/reverts to Automatic On operation.

1. Chanje Pèmèt
2. Chanje Enfim
3. Mòd prediksyon
4. Predictive Mode with Expiration.

5=Darkness Set-Point / Inhibit Set-Point
Nivo limyè anbyen kote Capteur a mete limyè yo nan anviwònman High Trim.

Anviwònman	Light Level (fc)	Nòt
1	Set NOW*	Default/current setting
2	0.1 fc	Very low light
3	1 fc	Limyè ki ba
4	4 fc	Moderate low light
5	8 fc	Limyè mwayen
6	16 fc	Medium-high light
7	24 fc*	Default recommended
8	32 fc	Limyè klere
9	48 fc	Trè klere
10	64 fc	Segondè limyè
11	Off	Light level off
12	96 fc	Maximum standard brightness
13	128 fc	Extra bright
14	192 fc	Extremely bright
15	256 fc	Anviwònman maksimòm

Set Now will automatically select the Darkness Set-Point based on the current conditions in the room. Lights will go to full bright and sensor will rapidly flash for 15 seconds, allowing the occupant to move out of direct view nan Capteur. Yon fwa seleksyon an fikse fin ranpli, Capteur a ap double-kliye nan konfimasyon.

7=Photocell Mode

Anpeche sèlman
Prevents lights from automatically coming on when light level is above the Inhibit Set-Point

1. Andikape
2. Anpeche sèlman

9=Restore Defaults
Returns all functions to their original settings.

1. Kenbe aktyèl*
2. Retabli Defo

11=LED Operation
Indicates behavior of the device’s LED.

1. Endikasyon Okipasyon*
2. Andikape

14 = Manyèl sou peryòd gras
Time period after lights automatically turn off that tho can be reactivated by motion, Applicable only when sensor is in Manual On (Semi Auto) mmie.

• I-Osec
• 3-15see

17 = Tan Prediksyon Sòti
Time period after manually switching fights off to leave the space. Applicob/e onbe when sensor in Predictive Off mode.

• I-5s«
• 2-6seg
• 3-7s«
• 4-8seg
• 5-9seg
• 6-10K*
• 7-15K
• 8-20seg
• 9-30K

18 = Tan Grace Prediktif
Time period after Predictive Exit Time fiat sensor rescans the RMRN for remaining occupants. Applicable only when sensor is in Predictive Off mode.

• I-Osec
• 2-5s«
• 3-10K
• 4-20 seg
• 5-30see
• 6-40K
• 7-50 seg
• 8-60seg

19 = Fennen sou pousantaj
Time required for light to reach preset IceL

• 1-0.75 see
• 2-25seg
• 3-5seg
• 4-15s«

20 = Pousantaj Fade Off
Time required for light to turn Off

• 1-0.75 seg
• 2-15see
• 3-5seg
• 4-15seg

ENSTRIKSYON ANFÒM OPERASYONÈ

PLEASE READ A1 1 7 STEPS BEFORE PROGRAMMING

• Enter programming mode by pressing & holding button until LED flashes rapidly. Release button.
• Enter a specific function by pressing button. The number Of times as the desired function number from the tables on the following pages (e.g., press twice for function 2, Occupancy Time Delay).
• The selected function’s current setting will then be read out in a sequenæ of LED flashes (e.g., five flashes for 10 min). TO change setting, proceed to step 4 before sequence repeats 10 times.
• While the sensor is flashing back current setting, interrupt it by pressing button the number of times for the new desired setting as indicated in the particular function’s detailed table (e.g., press seven times for 15 min). Sensor will begin to flash new setting as confirmation.
• Next, while the sensor is flashing back new setting, interrupt it by pressing and holding button until LED flashes rapidly. Release button.
• As final confirmation and activation Of the new setting, re-enter the function number that was changed (e.g., press twice for function 2, Occupancy Time Delay).
• LED will flash twice indicating acceptance of new setting. If two flashes are not seen, repeat 7 step process

Nòt:

TO exit programming mode without saving or to change to a different function, wait for the blink back sequence to repeat 10 times, then return to step 1.

GARANTI
5-ane garanti limite. Ranpli kondisyon garanti ki sitiye nan www.acuibrands.com/CustomerResourcesTerms_and_conditions.as x

LI AK SWIV TOUT ENSTRIKSYON SEKIRITE!

SOVE ENSTRIKSYON SA YO EPI DELIVRE BAY PWOPRIYETÈ A APRE ENSTALASYON

• Acuity Brands I One Lithonia Way Conyers, GA 30012
• Telefòn: 800.535.2465 www.acuitybrands.com/sensorswitch @2014-2021 Acuity Brands Lighting, Inc.
• All rights reserved. Rev. 09/27/21 lofl 912-00262-002

FAQ

How do I reset all settings to default?

Navigate to the Restore Defaults option and select 'Restore Defaults' to reset all functions to their original settings.

Dokiman / Resous

sensor switch WSRA Series Wall Switch Sensor with Occupancy [pdfGid Enstalasyon is-wsra 220VAC Edits V5, WSRA Series Wall Switch Sensor with Occupancy, WSRA Series, Wall Switch Sensor with Occupancy, Switch Sensor with Occupancy, Sensor with Occupancy

Referans

• Manyèl itilizatè