NOTHING Fixed Frame Screen Instruction Manual

NOTHING Fixed Frame Screen

Mèsi paske ou chwazi sèvi ak pwodwi nou an! Pou ou ka pi byen sèvi ak pwodwi a, tanpri li epi konsève manyèl sa a avèk atansyon anvan enstalasyon ak itilizasyon.

Every screen undergoes special quality checks. The manufacturer records a video of each screen produced in the factory to document the condition of the screen as ii leaves the factory. We recommend that you also record a video for documentation when unpacking the screen. This will facilitate the manufacturer in processing any service requests in case of issues. Damage that occurs during the installation cannot be claimed. Therefore, please be extremely careful as the screen material is very fragile, and avoid folding or denting it.

Pati

Prekosyon

1. Pou asire efè pwojeksyon ak bon jan kalite pwodwi sa a, tanpri obsève kondisyon fonksyònman sa yo.
2. Lè rasanble, jwenn yon etaj gwosè apwopriye oswa tab. Sifas la dwe pwòp epi san okenn obstak. Atè a oswa tab la dwe kouvri ak materyèl pwòp tankou twal, fim, dra, elatriye.
3. Manyen ak atansyon pandan enstalasyon pou anpeche aksidan pèsonèl oswa domaj pwopriyete.
4.  Pa touche sifas ekran pwojeksyon an ak men ou.
5. Pa manyen sifas pwojeksyon an ak objè byen file oswa difisil pou anpeche domaj nan materyèl ekran an. Pa ekri oswa desine sou ekran an.
6. Kenbe timoun yo lwen ekran an pou anpeche aksidan.
7. Sifas ekran an dwe netwaye ak trete regilyèman, epi li rekòmande pou pran swen li yon fwa chak de semèn.
   Please use a soft cotton cloth to gently wipe (dip some water), and it is not advisable to use any chemical cleaners or alcohol.

Rasanble ankadreman an

1. Louvri bwat anbalaj la epi kategorize epi fè aranjman pou konpozan yo byen, epi fè referans kwaze kantite yo ak lis verifikasyon "1.0 Pati".
2.  The horizontal frame is a segmented splicing type, and the two horizontal inner frames are spliced correspondingly as shown in the figure (Note: There is a mark in the middle of the splicing strip of the inner frame, and the splicing position must be guaranteed to be at the mark).
3. Premyèman, mete kat konektè kwen yo nan ankadreman vètikal enteryè a, jan yo montre nan dyagram nan.
4. Asanble ankadreman enteryè orizontal ak vètikal yo dapre dyagram nan. Apre ou fin asanble ankadreman enteryè yo, sere kwen yo ak vis M5X5, epi enstale tij sipò yo.

Rasanble ekran an

1.  Wear gloves (to avoid fingerprints on the screen that cannot be erased).Lay a clean cloth I’ non a flat, clean level countertop (or floor) that won’t hurt the screen.
2.  Take out the screen from the package, put the screen face down,to unfold the curtain roll, spread it flat on the cloth on the table, and then insert the glass fiber strips into the around the screen according to the length as shown below. Nòt enpòtan:
   Si se yon ekran anbyen ki rejte limyè ultra-kout, tanpri kolabore ak de moun pandan asanble a, evite pliye ekran oswa aksyon enpak friksyon objè difisil.
3. Place the assembled border on the screen. Note: The ultra-short focus anti-light scree has an up-and-down direction (other curtains have no direction). If it is an anti-light screen it should be matched with the direction of the frame. Adjust the position of the screen according to the lines marked on the four corners of the screen.
4.  Hook the screen on the frame with a tension spring. To hook the tension spring, please follow the following sequence, first, hook 1~8 springs; then hook springs 9~12, and then hook other springs from the middle spring to both sides in turn. Please refer to the attache drawing for the installation method of the tension spring
5. Apre pann sezon prentan an, kanpe ekran an epi tcheke plat la an jeneral nan ekran an. Si gen inegalite, prentan an bezwen ajiste lokalman jiskaske li nivo.
6. Is restored to the position of 4.4, ready to install the frame.

Enstalasyon ankadreman ekstèn

1. Mete ankadreman ekstèn lan kont ekran ankadreman an, aliyen kat kwen yo, epi bloke ankadreman enteryè ak ekstèn lan ak vis M4X8. Remak: Si gen yon LOGO sou ankadreman an, li ta dwe enstale anba ekran an.
2. Adjust the outer frame at the corner to the smallest gap, and then tighten the screws. Lock the corners one by one according to this method, and finally deal with the splicing of the horizontal outer frame (if the gap is found to be too large, you can push the left and right outer frames inward)
3. Finalman, mete pwoteksyon kwen yo sou kat kwen ankadreman an.

Enstalasyon ekran

1. Premye konfime anwo ak anba bracket miray la ak direksyon enstalasyon an
2. Install wall hangers on the wall according to screen size. Required tools: level, hammer drill, pencil, ladder, etc. As shown below, the horizontal direction is about 30cm away from both sides of the screen. Please estimate the installation position of the screen before installing the wall pendants. The height of the lower edge of the screen from the ground is generally about 600″800mm.
3. Hang the screen on the wall according to the method shown in the picture.

FAQ