P1、P2、P3、P4、P5

DIM/CT/RGB/RGBW/RGBCW dirije kontwolè

• Small size and light weight. The housing is made from V0 flame retardant
• PC materials from SAMSUNG/COVESTRO.
• Fonksyon gradyasyon mou-sou ak fennen-nan amelyore konfò vizyèl ou.
• 2.4GHz wireless signal , eliminating the need for signal wiring.
• 1-5 channel constant voltage pwodiksyon an.
• Kontwole DIM, CT, RGB, RGBW, RGBCW limyè.
• Travay ak yon seri MINI RF 2.4GHz remote.
• P3, P4 and P5 have 9 built-in dynamic modes.
• One controller can be paired up with 10 remotes .
• Sync efè dinamik ant contrôleur nan menm gwoup/zòn.

Espesifikasyon teknik

Modèl	P1	P2	P3	P4	P5
Siyal Antre	RF2.4GHz
Antre Voltage	12-48V =
Sòti Voltage	12-48V
Chanèl	1CH	2 CH	3 CH	4 CH	5 CH
Reyajiste switch	Wi	Wi	Wi	Non	Non
Chaje aktyèl	Max. 11A	Max. 12A	Max. 15A	Max. 15A	Max. 15A
Chaj pouvwa	132W@12V 240W@24V 288W@36V 384W@48V	144W@12V 240W@24V 288W@36V 384W@48V	180W@12V 360W@24V 432W@36V 432W@48V	180W@12V 288W@24V 360W@36V 480W@48V	180W@12V 360W@24V 450W@36V 600W@48V
Compatible Remote Contro Models	Single-zone: M1A/M1B Multi-zone: M1C/M1D Programmable: M9	Single-zone: M1A/M1B/M2A/M2B Multi-zone: M1C/M1D/M2C/M2D Programmable: M9	Single-zone: m1A/M113/m2A/m2B1 M4A/M4B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D Programmable: M9	Single-zone: m1A/m113/M2A/m2B1 M4A/M4B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D Programmable: M9	Single-zone: M1A/M1B/m2A/M2B/ M4A/m4B/M5A/M5B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D/M5C/M5D Programmable: M9
Pwoteksyon	Short circuit protection, over-temperature protection, over-current protection, and reverse connection prevention protection
Tanperati travay.	-25 ° C - 50 ° C
Dimansyon	L91 xW37xH21(mm)
Gwosè pake	L94xW39xH22(mm)
Pwa (GW)	46g

Gwosè pwodwi

Inite: mm

Tèminal Deskripsyon

Dyagram fil elektrik

When P1 is connected to the dimmable light stripWhen P2 is connected to the dimmable light stripWhen P2 is connected to the color temperature light stripWhen P3 is connected to the dimmable light stripWhen P3 is connected to the color temperature light stripWhen P3 is connected to the RGB light strip

Nòt: The control type of PUSH DIM will switch according to the type of the remote control.
When P4 is connected to the dimmable light strip

When P4 is connected to the color temperature light strip

When P4 is connected to the RGB light strip

When P4 is connected to the RGBW light strip

When P5 is connected to the dimmable light strip

When P5 is connected to the color temperature light strip

When P5 is connected to the RGB light strip

When P5 is connected to the RGBW light strip

When P5 is connected to the RGBCW light strip

Pè remote la

Pair the remote by using the button

1. Short press the ID learning button on the controller and the indicator light flashes. Please complete the following steps within 10 seconds.
2. Pair the MINI series remote:
   Single-zone MINI remote: Long press the ON/OFF button until the controller’s indicator light flashes fast.
   Multi-zone MINI remote: Long press zone button until the controller’s indicator light flashes fast.
3. When the load light of the controller flashes slowly and then stays on constantly, the learning is successful.

Pair the remote by powering on the controller

1. Power off the controller first.
2. Pair the MINI series remote:
   Single-zone MINI remote: Long press the ON/OFF button and power on the controller at the same time until the controller’s indicator light flashes fast.
   Multi-zone MINI remote: Long press zone button and power on the controller at the same time until the controller’s indicator light flashes fast.
3. When the load light of the controller flashes slowly and then stays on constantly, the learning is successful.

Nòt: A controller can be paired with a maximum of 10 remotes. Pairing more than 10 remotes will automatically delete the earliest remote ID codes.

Unpair the remote

Unpair the remote by using the button:

1. Delete all remote parings
   Long press the ID learning button on the controller for 10 seconds, and then short press it for 6 times. When controller’s indicator light flashes and then stays on, pairing removal is successful.
2. Delete a single remote paring
   Single-zone Mini: Press and hold the ID learning key of the controller for 5 seconds. Within 10 seconds, press the on/off key three times briefly. When the load light flashes slowly and then stays on constantly, the code clearing is successful.
   Multi-zone Mini: Press and hold the ID learning key of the controller for 5 seconds. Within 10 seconds, press the zone key three times briefly. When the load light flashes slowly and then stays on constantly, the code clearing is successful.

Unpair the remote by powering on the controller

Delete a single remote paring
Single-zone Mini: Power on the controller for 2 seconds, then power it off for 2 seconds, and power it on again. Press the on/off key three times briefly within 3 seconds. When the load light flashes slowly and then stays on constantly, the code clearing is successful.
Multi-zone Mini: Power on the controller for 2 seconds, then power it off for 2 seconds, and power it on again. Press the zone key three times briefly within 3 seconds. When the load light flashes slowly and then stays on constantly, the code clearing is successful.

Prekosyon enstalasyon

Please do not stack the products. The distance between two products should be ≥15cm so as not to aect heat dissipation and the lifespan of the products.Please do not place the products on the . The distance between the product and the should be ≥100cm so as to avoid signal interference.Tanpri pa mete pwodwi yo toupre yon gwo zòn nan objè metal (tankou plafon poto metal). Distans ki genyen ant pwodwi a ak objè metal la ta dwe ≥15cm pou evite entèferans siyal.                        Tanpri pa enstale pwodwi yo sou travès oswa toupre kwen yo. Distans ki genyen ant pwodwi a ak gwo bout bwa a oswa kwen an ta dwe ≥15cm pou evite entèferans siyal.

Atansyon

• Enstalasyon pwodwi ak komisyonin ta dwe fèt pa yon pwofesyonèl ki kalifye.
• Pwodwi LTECH yo epi yo pa lightningproof ki pa enpèmeyab (modèl espesyal eksepte). Tanpri evite solèy la ak lapli. Lè enstale deyò, tanpri asire yo monte nan yon patiraj prèv dlo oswa nan yon zòn ki ekipe ak aparèy pwoteksyon zèklè.
• Bon dissipation chalè pral pwolonje lavi pwodwi a. Tanpri enstale pwodwi a nan yon anviwònman ki gen bon vantilasyon.
• During installation, avoid being close to large-area metallic objects or stacking the devices, so as to prevent signal interference from affecting the usage.
• Avoid installing in thunderstorm-prone areas, areas with strong magnetic fields, and high-voltage zòn yo.
• Lè ou enstale pwodui sa a, tanpri evite tou pre yon gwo zòn nan objè metal oswa anpile yo pou anpeche entèferans siyal.
• Tanpri tcheke si vol travay latage itilize konfòm ak kondisyon yo paramèt nan pwodwi a.
• Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may cause a short circuit and damage the components, or trigger a accident.
• Si gen yon defo, tanpri pa eseye ranje pwodwi a poukont ou. Si ou gen nenpòt kesyon, tanpri kontakte founisè a.
• Manyèl sa a sijè a chanjman san lòt avi. Fonksyon pwodwi depann sou byen yo. Souple ou lib pou kontakte distribitè ofisyèl nou yo si ou gen nenpòt kesyon.

Nòt: The temperature within the installation area should be within the working temperature range of the products. Please do not install products inside LED es to avoid temperature exceeding the working temperature that may aect the product lifetime.

Akò garanti

Peryòd garanti apati dat livrezon an: 5 ane.
Sèvis reparasyon oswa ranplasman gratis pou pwoblèm kalite yo bay nan peryòd garanti.
Esklizyon garanti anba a:

• Pi lwen pase peryòd garanti.
• Nenpòt domaj atifisyèl ki te koze pa gwo voltage, Surcharge, oswa move operasyon.
• Pwodwi ki gen gwo domaj fizik.
• Domaj ki te koze pa dezas natirèl ak fòs majeures.
• Etikèt garanti ak kòd bar yo te domaje.
• Pa gen okenn kontra ki siyen pa LTECH.

1. Reparasyon oswa ranplasman yo bay se sèl remèd pou kliyan yo. LTECH pa responsab pou okenn domaj aksidan oswa konsekan sof si li nan lalwa.
2. LTECH gen dwa pou amande oswa ajiste kondisyon garanti sa a, epi divilgasyon alekri va genyen.

ZHUHAI LTECH TEKNOLOJI CO, LTD.
Add: No. 183 , Shui’an 1st Road, Xiangzhou
District, 519060 Zhuhai City
REPUBLIK PEP LA CHIN
Websit: www.ltech-led.com

Dokiman / Resous

LTECH P1 RGBCW LED Controller [pdfManyèl Pwopriyetè a P1, P1 RGBCW LED Controller, RGBCW LED Controller, LED Controller, Controller

Referans

• Manyèl itilizatè