LANCOM Systems ON-D8a Lancom AirLancer
Plis paseview of the mounting kit
- 1 connection flange (A)
- 1 connection arm (B)
- 1 pole flange / wall bracket (C)
- 4 washers M6 (D)
- 4 spring washers M6 (E)
- 4 nuts M6 (F)
- 1 pole clamp for pole diameter up to 62.5 mm (I)
- 2 hexagon head screws M8x35 (J)
- 4 spring washers M8 (K)
- 4 washers M8 (L)
- 2 nuts M8 (M)
- 2 hexagon head screws M8x70 (N)
Pa enkli nan sijè ki abòde lan livrezon
2 bann clamps for pole diameter > 62.5 mm (H)
Mounting the antenna flange and connection arm
Screw the connection flange (A) to the back of the antenna housing using the enclosed washers (D), spring washers (E), and nuts (F). Make sure that the spring washers (E) are located directly under the nuts (F).
Then fasten the connection arm (B) hand-tight to the connection flange (A) using a screw (J), a spring washer (K), a washer (L), and a nut (M). Make sure that the spring washer (L) is located directly under the screw head.
Preparasyon pou aliye miray la
Si ou vle monte antèn la sou yon miray, sèvi ak miray ranpa a (C) kòm yon modèl perçage pou make twou yo fè egzèsis pou aliye miray la.
Fè twou korespondan yo nan mak yo epi mete goujon (ki pa enkli) nan yo si sa nesesè. Tou depan de materyèl miray la ak kondisyon, pwofondè ak dyamèt twou yo dwe ajiste.
Montaj miray antèn la
- Aliman bracket miray la ak twou egzèsis yo epi tache li ak vis apwopriye.
- Now hand-tighten the connection arm (B) already mounted on the connection flange (A) to the wall bracket (C) using a screw (J), a spring washer (K), a washer (L), and a nut (M).
- Make sure that the spring washer (K) is located directly under the screw head and that the arrow on the back of the antenna housing is pointing upwards.
- Aliman antèn la selon volonte ou ak Lè sa a, sere boulon vis yo nan bra a koneksyon ak koupl apwopriye.
Poto aliye antèn la
Position the pole flange (C) at the desired height on a suitable pole with sufficient load-bearing capacity. Use the pole clamp (I) to attach to poles up to 62.5 mm in diameter.
- Fasten the pole clamp (I) to the pole flange (C) using the two screws (N), the spring washers (K), and the washers (L). Please note that the mast clamp must be rotated depending on the mast diameter.
- For pole diameters over 62.5 mm, you need suitable band clamps (H) (not included in the scope of delivery) and guide them through the pole flange and around the pole as shown in the overview
and tighten them after you have aligned the pole flange.
- Then connect the pole flange (C) hand-tight to the connection arm (B) already mounted on the antenna using an enclosed screw (J), a spring washer (K), a washer (L), and a nut (M).
- Make sure that the spring washer (K) is located directly under the screw head and that the arrow on the back of the antenna housing is pointing upwards.
- Aliman antèn la selon kondisyon ou yo ak Lè sa a, sere boulon vis yo nan bra a koneksyon ak koupl apwopriye.
Enfòmasyon enpòtan
- Responsab manyen frekans segondè
Pou konfòme yo ak kondisyon pwoteksyon Inyon Ewopeyen Directive 2014/53 ak EN 62479 konsènan restriksyon debaz yo pou sekirite moun ki nan jaden elektwomayetik ak "Politik FCC sou Ekspozisyon Imèn nan jaden elektwomayetik radyofrekans", li nesesè konfigirasyon. genyen antèn ki kòrèk la nan routeur WLAN oswa pwen aksè WLAN. - Lwa sou ekipman elektrik ak elektwonik
Tanpri pa jete fatra elektrik ak elektwonik nan fatra kay, kote yo pa ka resikle. Asire w ke dechè elektrik ak elektwonik ou yo jete an akò ak direktiv ki valab nan peyi w kounye a. - Manyen kòrèk nan câbles antèn
Kab antèn yo se câbles RF sansib. Lè w ap mete yo, li enpòtan pou asire ke câbles yo pa pliye epi yo koube pi piti ke posib, paske sa ka lakòz pèt an tèm de pèfòmans antèn. Menm jan an tou, câbles antèn yo pa ta dwe blese nan bouk kab sere. - Antèn genyen ak revokasyon pò antèn ki pa itilize sou pwen aksè
Koneksyon antèn ki pa itilize sou pwen aksè a dwe sispann ak yon antèn baton ki fèmen. Pou pwen aksè andedan kay la, yo ka itilize rezistans tèminal ki enkli ak adaptè AirLancer AN-RPSMA-NJ. Anplis de sa, yo dwe espesifye benefis antèn nan konfigirasyon pwen aksè a.
Done teknik
- Frekans ranje 4,900 - 5,900 megaèrts
Karakteristik antèn
- Radiation patterns Horizontally: 8° Vertically: 8°
- Recommended use Point-to-Point
- VSWR 2.0:1 max.
- Gain 21 dBi max.
Done mekanik
- Dimansyon (mm) 370 x 370 x 30 (W x H x P)
- Weight 1,800 g (Antenna without mounting kit)
- Tanperati opere -40 ° C a 85 ° C
- Color Light grey
- Material UV resistant plastic
- Mounting options Wall- and pole mounting, alignable
- Cables & Connectors 2x 100 cm ULA100 cable with N-Plug connector
Atik
- Garanti 2 zan pou AirLancer ak Pwodwi pou Telefòn
- Atik non. 61708
- Scope of delivery Antenna, 2 connection cables, mounting kit for wall and pole mounting
LANCOM Systems GmbH
Yon konpayi Rohde & Schwarz Adenauerstr. 20/B2
52146 Wuerselen | Almay
info@lancom.de | lancom-systems.com
LANCOM, LANCOM Systems, LCOS, LANcommunity, LANCOM Service LANcare, LANCOM Active Radio Control, and AirLancer are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omis-
sions. 111436 09/2025
Kesyon yo poze souvan
K: Kisa mwen ta dwe fè si kèk pati ki manke nan pake a?
A: Kontakte sipò kliyan pou asistans nan jwenn pati ki manke yo.
Q: How do I ensure proper alignment of the antenna during mounting?
A: Follow the provided instructions carefully and use appropriate tools to align the antenna as needed.
Dokiman / Resous
 |
LANCOM Systems ON-D8a Lancom AirLancer [pdfManyèl Enstriksyon ON-D8a Lancom AirLancer, ON-D8a, Lancom AirLancer, Lancom, AirLancer |