KOLINK INSPIRE K8 Midi Tower Case
Manyèl itilizatè
Espesifikasyon
| Karakteristik | Detay yo |
|---|---|
| Kalite Ka | Sou entènèt jwèt Midi Tower |
| Sipò pou plak mèr | ATX, Mikwo-ATX, Mini-ITX |
| Kondwi Bays | 2 x 3.5″, 2 x 2.5″ |
| Fant ekspansyon | 7 |
| Sipò pou refwadisman | Front: 3 x 120mm, Top: 2 x 120mm, Rear: 1 x 120mm |
| Dimansyon | Apeprè. 200mm x 430mm x 380mm |
Kontni pake
- Kolink Inspire K8 Case
- Manyèl itilizatè
- Twous akseswa
ENSTRIKSYON ENSTALASYON
RETIRE PANN AVÈ/KOTE
- Retire panèl devan an lè w rale ak anpil atansyon anba panèl la.
- Retire panèl bò gòch la lè w retire 4 thumbscrews yo epi leve panèl bò glas la lwen ka a.
- Remove the right side panel bv removing the two rear thumbscrews and sliding the panel backwards.
ENSTALASYON MÈT
- Fè aliman plak mèr ou a ak chasi a pou jwenn kote yo ta dwe enstale kanpe-off yo.
- Yon fwa fè, retire plak mèr la epi tache stand-off kòmsadwa.
- Mete plak mèr ou 1/0 nan dekoupaj ki nan dèyè ka a.
- Mete plak mèr ou a nan chasi a, asire w ke pò dèyè yo anfòm nan plak 1/0 la.
- Sèvi ak vis yo bay yo pou mete plak mèr ou a nan chasi a.
Enstalasyon ekipman pou pouvwa
- Aace PSU in the bottom rear of the case, within the PSU shroud.
- Align the holes and secure With screws.
ENSTALASYON KAT GRAPHIK/KAT PCI-E
- Remove the rear PCI-E slot covers as necessary (depending on the slot size of your card).
- Pozisyon ak anpil atansyon epi glise kat PCI-E ou an plas, apresa sekirize ak vis kat siplemantè yo apwovizyone.
2.5″ SSD ENSTALASYON
Secure the supplied SSD screws tc the 2.5″ SSD and then slot into the drop and lock slots on top of the PSU shroud and secure.
3.5″ HDD ENSTALASYON
Secure the supplied HDD screws to the 3.5″ HDD and then slot into the drop and lock slots behind the PSU shroud and secure.
Enstalasyon fanatik anlè
- Retire filtè pousyè a nan tèt ka a.
- Aliman fanatik ou a (yo) nan twou vis yo sou tèt chasi a epi an sekirite ak vis.
- Ranplase filtè pousyè ou a yon fwa sekirize.
Enstalasyon fanatik devan/dèyè
Aliman fanatik ou a nan twou vis yo sou chasi a epi an sekirite ak vis.
Enstalasyon radyatè a dlo refwadisman
Secure the fans to the radiator, then fasten the radiator inside the chassis b} with strews from the Outside.
1/0 ENSTALASYON PANNEL
- Carefully check the labelling of each connector from the 1/0 panel to identify their function.
- Referans kwaze ak manyèl la kat mèr pou jwenn kote chak fil yo ta dwe enstale, Lè sa a, an sekirite youn nan yon tan. Tanpri asire yo enstale nan polarite ki kòrèk la pou evite ki pa fonksyone oswa domaj.
FAQ
What motherboards are compatible with the Kolink Inspire K8?
Ka a sipòte plak mèr ATX, Micro-ATX, ak Mini-ITX.
Konbyen fanatik ka enstale nan ka a?
No, fans are not pre-installed. You need to purchase them separately.
Ki longè maksimòm GPU ki sipòte?
The case supports GPUs up to approximately 330mm in length.
Kouman pou mwen netwaye filtè pousyè yo?
Remove the filters from the case and clean them with compressed air or wash them with water and let them dry completely before reinstalling.
Dokiman / Resous
 |
KOLINK INSPIRE K8 Midi Tower Case [pdfManyèl Itilizatè 04023, ANL-INT, INSPIRE K8 Midi Tower Case, INSPIRE K8, Midi Tower Case, Tower Case, Case |