KMC CONTROLS STE-9000 series NetSensor Damage from Incorrect
Espesifikasyon
- Product: STE-9000 series NetSensor
- Features: Temperature and humidity readings
- Model: All STE-9000 series NetSensors
Enstriksyon Itilizasyon Pwodwi
- Ensure that both tabs on the sensor cover rest on top of the backplate.
- Make sure the anti-tamper hex screw is fully rotated into the backplate before installing or uninstalling the sensor cover.
- Swing the cover from the top onto the backplate.
- Do NOT push the cover directly onto the plate or swing it from the bottom.
- If any force seems to be needed, check the alignment of the tabs on the top of the backplate and/or the anti-tamper screw before swinging the sensor cover onto the backplate.
- For more detailed installation instructions, please refer to the STE-9000 Series NetSensors Installation Guide.
Konplete etap sa yo pou monte yon NetSensor Digital KMC Conquest STE-9000 Series epi konekte li ak yon Kontwolè Conquest BAC-59xx/9xxx.
REMAK: Gade la Conquest NetSensors STE- 9000 Series Digital Room Sensors fèy done ak la Gid Seleksyon Konkèt at kmccontrols.com for specifications and other information.
AVI
- OBSERVE PREKOSYON POU MANYEN APÈYÈ ELEKTROSTAtik SANSIB
CHWAZI KOTE MONTAGE
- Gade la Chanm Capteur ak Thermostat Mounting Location ak Gid Aplikasyon Antretyen for cautions, troubleshooting, and best practices.
REMAK: Ranpli rough-in-wiring nan chak kote anvan enstale yon Capteur.
RETIRE PLAK DEYE
- Turn the hex screw(1) clockwise into the sensor until the screw clears the cover.
REMAK: The hex screw(2_ should remain in the backplate.
- Rale kouvèti a sou plak dèyè a.
KONEKTE KAB ETHERNET - Feed the Ethernet patch cable(3) from the Conquest controller through the center of the backplate(4).
REMAK: Kab patch Ethernet la ta dwe yon maksimòm de 150 pye (45 mèt).
- Monte plak la sou yon bwat elektrik lè l sèvi avèk vis yo bay yo.
REMAK: If additional thermal insulation is needed, install the optional HPO-9002 gasket before installing the backplate.
Pou plis enfòmasyon, gade nan Room Sensor and Thermostat Mou
nting Location and Maintenance Application Guide. - Ploge kab Ethernet 5 la nan Jack modilè 6 nan Capteur a.
ENSTALE KOUVRI CAPTEUR - Place the cover(7) over the top of the backplate(8) and swing it down.
REMAK: Fè atansyon pou pa zongle kab Ethernet la.
- Turn the hex screw(9) counterclockwise until it engages the cover.
OPERE
- The STE-9000 Series NetSensor becomes operational after it is connected to a powered Conquest controller.
- REMAK: To change setpoints or configuration, see the Gid aplikasyon KMC Conquest Controller.
- REMAK: For continued maximum NetSensor efficiency, see the maintenance section in the Chanm Capteur ak Thermostat Mounting Location ak Gid Aplikasyon Antretyen.
AVI ENPÒTAN
- Materyèl ki nan dokiman sa a se pou enfòmasyon sèlman. Kontni yo ak pwodwi li dekri yo ka chanje san avètisman.
- KMC Controls, Inc. makes no representations orwarranties with respect to this document. In no event shall KMC Controls, Inc. be liable for any damages, direct, or indirect, arising out of or related to the use of this document.
- Logo KMC a se yon mak ki anrejistre KMC Controls, Inc. Tout dwa rezève.
KONTAKTE
- TEL: 574.831.5250
- FAKS: 574.831.5252
- imel: info@kmccontrols.com
FAQ
Q: Which models are affected by the installation issue?
A: This issue affects all STE 9000 series NetSensors.
Q: What are the potential errors from a damaged printed circuit board?
A: Incorrect temperature and humidity readings may result from a damaged printed circuit board.
Dokiman / Resous
 |
KMC CONTROLS STE-9000 series NetSensor Damage from Incorrect Installation [pdfGid Itilizatè STE-9000 series NetSensor Damage from Incorrect Installation, STE-9000 series, NetSensor Damage from Incorrect Installation, NetSensor Damage from Incorrect Installation, NetSensor Damage, from Incorrect Installation |