Sistèm alam siveyans presyon kawotchou USB Android TPMS

Tire Pressure Detection System for Automobile
Yon manyèl enstriksyon(Special for USB tire pressure monitoring)

Pwodwi Profile

Thank you for choosing our tire pressure monitoring system. Before using this product, please read the installation instructions carefully. wish you safe driving!
This product contains four sensors and a receiver. The sensor is used to monitor the pressure and temperature in tire in real time. The pressure and temperature data collected by the sensor are sent to the receiver by radio frequency. The receiver transmits the data to the vehicle navigation processing through USB port and displays them. According to the set standard pressure and temperature alarm values, corresponding alarms are issued for different abnormal situations to prompt users to deal with them in time, so as to avoid traffic accidents and ensure traffic safety.

Nòt espesyal

1. This product is suitable for Android navigation machine with USB interface. For specific model and software upgrade, please consult the corresponding navigation distributor.
2. Before installing this product, please confirm whether this product is suitable for your navigation, and read this manual carefully to avoid adverse effects on your body and this product.
3. This product can monitor, display and remind abnormal tire pressure, but it can not prevent the occurrence of tire burst accidents.
4. In normal use, when the tire pressure and temperature are abnormal, the product system will automatically pop up the display box display and alarm sound reminder through the navigation interface. In order to ensure your safety from the vehicle, please do not pay attention to the navigation tire. pressure interface for a long time during the driving process. When encountering special circumstances, please pay attention to observe the road and find a safe place to stop for vehicle inspection.
5. The first four sensors of this product have been matched with the receiver. You just need to install the receiver to open the navigation tire pressure software interface and install the sensor to use directly without any other operation, so as to avoid affecting the normal use of the product.
6. It is suggested that the receiver be installed to open the tyre pressure interface of navigation, and then the sensor be installed. During installation, the navigation software interface of tire pressure is usually displayed one by one. It is normal to see “00” or “00” flashing during the first installation. The tire can be properly displayed after aeration and deflation or vehicle start-up.
7. In the course of driving, due to the relationship between thermal expansion and cold contraction of gas in tire caused by friction, the change of air pressure and temperature will be on the high side or on the low side, which is a normal phenomenon.
8. When the tire pressure is too high, attention should be paid to preventing tire burst, when the tire pressure is too low, attention should be paid to fuel consumption and balance.
9. In general, there will be normal natural air leakage in tires. The tire pressure decreases with time, which is a normal phenomenon and has no direct relationship with the installation of this product.
10. There is a wireless connection between the sensor and the receiver, and the transmission distance is long enough. Product design has many
    anti-interference functions, and the possibility of interference is very low. but it does not exclude the abnormal use of products due to interference.
11. Please use this product correctly and use it within its allowable scope. If it exceeds its scope of use, the company will not be responsible for all the consequences.
12. The text of this instruction is subject to change without prior notice.

Zafè ki bezwen atansyon:

Because there are many brands of USB Android navigation in the market, the product is only compatible with more than 95% of the models at present. It is recommended to connect the receiver first, confirm the normal operation of APP and have temperature data, then install the sensor. If the data can not be displayed by the normal operation software, it is recommended to use solar energy products.

Enstriksyon enstalasyon yo

1. TPMS APP Installation

1. Copy the AP file named USBTPMS to the U disk
2. Connect the U disk to the USB interface of navigation, and open the navigation interface.
3. Open “AP Manager” or “File Manager” or other names on the navigation interface.
4. Find the U-disk path, then choose to install USBTPMS (or other models). After installation, open APP.

2. Enstalasyon reseptè

1. Find the USB interface for Android navigation
2. Two interface interpolation
3. Enstalasyon fini

Zafè ki bezwen atansyon:

1. The receiver receives the signal of the sensor wirelessly and transmits it to the vehicle navigation host.
2. The USB interface of navigation is usually hidden in the copilot’s storage box or some location in the front end of navigation. If you can’t find it, please consult the navigation dealer.
3. When installing the receiver, be sure to keep away from high-power equipment such as vehicle navigation, recorder, DR, mobile TV, etc. for at least 60 cm. (It is recommended that the receiver be fixed near the copilot the attached 3M glue)
4. Receiver needs to update tire information in real time. Because of the many tasks of vehicle navigation processing, when the tire pressure and temperature are normal, the vehicle DVD will not always process the latest data. Therefore, when the two observed data show the same, it does not belong to product failure.

Find the tire pressure receiver (the first connection to the tire pressure receiver can be as follows)

1. Insert the tire pressure receiver and confirm after selecting the TPMS device to trust.
2. After confirmation, the display software interface is as follows

(Remak: After installing the software, plug in the receiver and the above interface appears. It shows that this vehicle Android navigation is compatible with this product. Only then can the sensor continue to be installed.)

Enstalasyon Capteur

Zafè ki bezwen atansyon:
It is suggested to install it in a regular tire shop or 45 shop. The specific installation method can be guided by referring to the instructions or contacting the seller. Before installing the sensor, please install the receiver and run the tire pressure software, which is helpful to transmit the installed sensor data to the vehicle navigation display in time.
After installation of the sensor, check whether the tire is leaking, and if necessary, apply soapy water to the air nozzle to check and confirm. The company shall not be jointly and severally liable for the leakage caused by the installation and the failure caused thereby.
1.Installation process of built-in sensor
Nòt: Please install the hub according to the position corresponding to the identification on the sensor (left front, right front, left rear, right rear). The shovel of the tyre picking machine should not be shoveled above the sensor, otherwise it will damage the sensor, especially the tyre which has been installed with this product. When disassembling, please be sure to inform the relevant personnel.

1. Remove the valve nozzle of the original vehicle and install the sensor.
2. Adjust the position and use the tool to lock the sensor valve nozzle screw.
3. Assemble tires and wheels and refill them.
4. The upper balancer measures the speed of the motor balance, and then loads it back into the vehicle.

Installation of External Sensors

(Remak: When installing, screw the anti-theft nut to the bottom of the valve nozzle, and then tighten the external sensor. After installation, please check for air leakage).

1. Lock nuts into valve nozzle
2. Installation of sensors corresponding to tire position
   
3. Reverse locking of nuts and sensors
4. Ensure firmness and complete installation

After installing the sensor and opening the APP for 10 seconds, the tire pressure and temperature data on navigation show normal.
Jan sa a:

Battery Replacement Process with External Sensors

(Remak: When sensor voltage low alarm occurs, please replace new batteries in time, recommend imported CR1632 batteries, use batteries without quality assurance, the company will not be responsible for the use of products.) When replacing batteries, please follow the following process, especially the fourth step in the process must be operated. If this step is not operated, the company will not be responsible for the battery loss. The specific steps are as follows.

1. Fix the sensor base with a hexagonal wrench, and turn the sensor shell counterclockwise with the hand to completely unscrew the shell.
2. Remove the old batteries and put them away where children can’t touch them.
3. Remove the new battery and position the positive and negative electrodes according to the diagram.
4. Before installing the battery, please contact the positive and negative plates of the battery mounting seat for 1 second at the same time, and then load the battery.
5. After the battery is installed, the shell is tightened clockwise and the sensor is installed in the original position.

Konsèy: If the battery is not replaced in accordance with the above way, the product may not work because of the internal settings of the system. If this phenomenon occurs, please re-operate according to the above process.

Learning Matching:

1. The position information of the sensor has been stored in the receiver before the product is shipped. When installed, it is installed according to the position indicated by the shell.
2. When the sensor is damaged, new sensors need to be replaced, or when the tire is changed, this function can be operated.
3. When operating this function, please operate or consult the distributor according to the instructions of starting the matching part in DVD.
4. When the receiver is in the waiting state, the sensor of the corresponding position can be installed or disassembled from the vehicle air nozzle by the external sensor, and the built-in sensor can be inflated or deflated. When a pair is unsuccessful, it can be operated repeatedly.
5. When matching sensors, make sure that only one sensor is matched.

Paramèt Paramèt:

(Remak: The relevant alarm values have been set by default in accordance with industry standards before this product is manufactured. Users Usually no further operation is required. If there is actual need, the alarm threshold of low pressure, high pressure, high temperature and the adjustment switch of spare tire data can be set here.)
The default value of this product is:

1. Wo-voltage alarm value: > 3.1Ba
2. ba-voltage alarm value: <1.8Bar
3. High temperature alarm value: 75°C
4. Default Pressure Unit: Bar

Sensor Technical Parameters:

1. Travay Voltage: 2.1V ~ 3.6V
2. Measurement range of barometric pressure: 0-8Bar
3. Temperature Measurement Range: -40°C-125°C
4. Sensor Weight: External <10g, Built-in ≤34g
5. Waterproof Standard: IPx67
6. RF frekans: 433.92 MHz

Receiver Technical Parameters:

1. Travay Voltage: DC12V
2. Maximum operating current: less than 15 mA
3. high frequency operating frequency: 433.92 MHz
4. Working temperature: -40℃-85℃℃
5. Communication Line Length: 20cM
6. Fixing method: 3M glue

Terminological description of pressure unit:

Non	Eksplike
PSI	Unit of pressure: pounds/square inches
Bar	Pressure unit: Ba
Kpa	Unit of pressure: Kpaska (statutory in China)
Pressure Unit Conversion Relation	1Bar-100Kpa≈14. 5Psi
℃	Temperature Unit: Celsius Temperature

Garanti kloz

The company promises: during the warranty period, the products will be repaired or replaced free of charge in accordance with this warranty clause (except for exemption clause).

1. Warranty Period Provisions: Warranty Period is calculated from the time when the product leaves the factory, and the period is one year.
2. Users must provide or show the warranty when they request the product to be repaired during the warranty period.
   Fault products;
   The original purchase certificate without modification can clearly show the seller’s name and purchase date.
   The warranty card has been properly filled in.
3. Warranty does not apply to the following circumstances
   Mete nòmal;
   Damage caused by unauthorized disassembly and repair;
   Any change or modification of this product without the consent of the manufacturer;
   Artificial Damage Caused by Failure to Use, Maintain and Keep in accordance with the Instructions for Use of Products
   Failure or damage caused by other non-product design, material, manufacturing, quality and other problems
4. The product is damaged or affected by chemical factors such as corrosion and oxidation when it is used beyond the prescribed conditions.

Kat garanti

User Name………………………
Modèl………………………………
Date of purchase……………….
Contac information……………
Adrès………………………………..
Dosye antretyen
Dat…………………………………………….
Faut phenomena………………….
Causes of failure…………………
Repair personnel………………….

Dokiman / Resous

Kebidumei USB Android TPMS Tire Pressure Monitoring Display Alarm System [pdfManyèl Enstriksyon USB Android TPMS Tire Pressure Monitoring Display Alarm System, TPMS Tire Pressure Monitoring Display Alarm System, Pressure Monitoring Display Alarm System, Monitoring Display Alarm System, Display Alarm System

Referans

• Manyèl itilizatè