growplay Compact Monkey Bars

ATANSYON!
READ ALL SAFETY INFORMATION, INSTALLATION AND USAGE INSTRUCTIONS PR IO R TO INSTALLATION AND USAGE. See growplaymonkeybars.com for step-by-step video instructions and any updates to these instructions.

Swen & Antretyen

Improper maintenance or lack of care can lead to your system deteriorating earlier than expected and causing injury. Please follow these instructions to ensure that your product lasts for as long as possible.

Swen jeneral

• Retain this Manual.
• Enspekte anvan ak apre chak itilizasyon.
• Replace any worn, deteriorated, defective or missing parts immediately and only through Growplay.
• Tighten all hardware, including elements that secure the system to the ground.
• Keep away objects that could damage textile components.
• Ensure that moving steel components remain well lubricated.
• Use only parts and accessories recommended by Growplay.

Rouye ak korozyon

• Be aware of, and check, areas that are particularly prone to rusting:
  • Places where water is easily trapped.
  • Hollow sections of steel (which can appear in good condition on the outside, while hiding rust on theinside).
  • Sections where steel components join.
• Inspect the inside of all tubes every 6 months – as well as after rain – and remove any water from the inside surfaces.
• Use general-purpose grease on steel connection areas.
• Avoid cleaning steel components excessively; it may reduce the effectiveness of their protective coatings.

Textile deterioration

•  Remove textile parts and store them – in their original packaging – in a cool, dry and dark place when the system will be unused for over 1 month. Prolonged exposure to UV sunlight can shorten the lifespan of textile materials.

Weather care

Components are susceptible to deterioration from use and environmental conditions – such as sunlight, rain, salt and heat – to varying degrees. If your system will be unused for any extended period, disassemble it, return it to its original packaging and store it in a dry place.

• RAIN: Remove any fallen debris after rain and wipe off residual water with a dry cloth. Moisture left on the
• WIND: Disconnect any accessories and cover the frame with a storm cover.
• HEAT: Cover when not in use to minimise UV damage.

Usage and Behaviour

Improper use of, or behaviour on, your system can lead to serious injury. Please follow these usage and behaviour instructions to ensure safe play.

Enfòmasyon pou itilize san danje

• Maximum user weight: 1653 lb (750 kg).
• Itilize domestik ak deyò sèlman.
• Suitable for ages 6 and over.
• Maximum users at one time: 4

Enfòmasyon sou materyèl sifas lakou rekreyasyon
Enfòmasyon sa yo soti nan Seksyon 4 nan Manyèl Sekirite Lakou Rekreyasyon Deyò Komisyon Sekirite Pwodui Konsomatè Etazini (USCPSC) pou materyèl sifas lakou rekreyasyon.

Seksyon 4 nan Manyèl Sekirite Lakou Rekreyasyon Deyò Lakay Komisyon Sekirite Pwodui Konsomatè a

X3.1 Chwazi sifas pwoteksyon
Youn nan bagay ki pi enpòtan ou ka fè pou diminye chans pou blesi nan tèt grav se enstale sifas pwoteksyon chòk-absòbe anba ak toupatou nan ekipman jwe ou. Sifas pwoteksyon an ta dwe aplike nan yon pwofondè ki apwopriye pou wotè ekipman an akò avèk ASTM Specification F1292. Gen diferan kalite sifas yo chwazi nan; kèlkeswa pwodwi ou chwazi a, swiv direktiv sa yo:

X3.1.1 Materyèl ranpli ki lach:

• X3.1.1.1 Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips,engineered wood fiber (EWF), or shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet high.

NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. Thesurfacing will also compact, displace, and settle, and should be periodically refilled to maintain at least a 9-inch depth.

X3.1.2 Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet inheight.

If maintained properly, this should be adequate.
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface.A fall onto a hard surface can result in serious injury to the equipment user. Grass and dirt are notconsidered protective surfacing because wear and environmental factors can reduce their shockabsorbing effectiveness. Carpeting and thin mats are generally not adequate protective surfacing. Ground-level equipment such as a sandbox, activity wall, playhouse, or other equipment that has no elevated play surface does not need any protective surfacing.

X3.1.3 Sèvi ak kontènman
Tankou fouye toutotou perimèt la ak/oswa mete bòdi jaden sou perimèt la. Pa bliye pran an kont drenaj dlo a.

• X3.1.3.1 Check and maintain the depth of the loose-fill surfacing material. To maintain the right amount of loose-fill materials, mark the correct level on play equipment support posts. That way, you can easily see when to replenish and/or redistribute the surfacing.
• X3.1.3.2 Pa enstale sifas ki lach ranpli sou sifas difisil tankou beton oswa asfalt.

X3.1.4 Sifas ki te vide sou plas oswa mozayik kawoutchou prefabrike

You may be interested in using surfacing other than loose-fill materials like rubber tiles or poured-inplace surfaces.

• X3.1.4.1 Installations of these surfaces generally require a professional and are not “do-it-yourself” projects.
• X3.1.4.2 Review espesifikasyon sifas anvan achaasing this type of surfacing. Ask the installer/manufacturer for a report showing that the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height – vertical distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below – of your play equipment.
• X3.1.4.3 Tcheke sifas pwoteksyon an souvan pou mete.

X3.1.5 Plasman

Li enpòtan pou byen plase epi byen antreteni sifas pwoteksyon yo. Asire w ou:

• X3.1.5.1 Pwolonje sifas omwen 6 pye de ekipman an nan tout direksyon.
• X3.1.5.2 Pou balanse pou ale-an, pwolonje sifas pwoteksyon devan ak dèyè balanse a nan yon distans ki egal a de fwa wotè ba an tèt kote balanse a sispann.
• X3.1.5.3 Pou balanse kawotchou, pwolonje sifas nan yon sèk ki gen reyon ki egal a wotè chèn oswa kòd sispansyon an, plis 6 pye nan tout direksyon.

This information has been extracted from the CPSC publications “Playground Surfacing — Technical Information Guide” and “Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending a postcard to the Office of Public Affairs, U.S. Consumer Product Safety Commission, Washington, D.C., 20207 or call the toll-free hotline: 1-800-638-2772.

Due care when installing product

• WARNING! Due care must be always taken whilst installing your product.
• WARNING! Improper installation, adjustment or maintenance can cause property damage, injury or death.
• Ensure you always follow the steps in the manual.

Enstriksyon pou itilize san danje
ADULT SUPERVISION IS REQUIRED AT ALL TIMES WHILST EQUIPMENT IN USE

WARNING: To reduce the risk of injury while using the system, enforce the following:

• Ensure that the system has been assembled by an adult, in accordance with the assembly instructions.
• Ensure that the system has been checked over before use, and that all attachments are secure.
• Do not use in strong wind conditions or wet weather and keep the system secure.
• Always ensure active and competent adult supervision while children are using the system.
• Wear comfortable clothing, which allows full and free movement, and closed-in footwear.
• Do not wear jewellery, drawstrings, cords, loops, buckles or anything that could entangle in components and become a strangulation hazard, a contact hazard or damage the system.

Empty pockets before use.

• Exercise caution at heights.
• Make sure that the areas around, underneath and above the system are clear.
• Demonstrate safe use for children before allowing them onto the system.
• Pa mache tou pre, devan, dèyè, oswa ant bagay k ap deplase.
• Do not attach items that are not specifically designed for use with the system, such as – but not limited to – jump ropes, clothesline, pet leashes, cables and chains.
• Install the system on level ground and in a well- lit area, no less than 2 m (6 ft) from any structure or obstruction – such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
• Ensure that your chosen surface allows the system to be firmly embedded with the included ground spikes or anchors.
• Only install the system on a surface with impact attenuating properties – such as grass, sand or soil. A fall onto a hard surface can result in serious injury or death to the equipment user.
• Check that you have all parts required for assembly.
• Lock nuts and bolts securely.
• Timoun yo pa dwe itilize ekipman an jiskaske li byen enstale.

Pre-assembly and installation tips
ASSEMBLY: TWO PERSONS REQUIRED

Before starting assembly, please carefully read the following information:

• Items required for assembly: Ladder, rubber mallet and spanner.
• Two people are required to assemble the frame.
• PA SERE BOULON YO FÈTMAN JISKASKE ANKAD LA FIN ASANBLE.
• Lay out all parts as shown at the start of each step.
• Asire w ou verifye tout sere boulon pyès yo de fwa epi asire w ankadreman an stab apre asanblaj la. Ti mouvman nan ankadreman an nòmal.
• Bay ase tan pou asire ke ba makak ou yo byen enstale epi san danje pou itilize.
• Asire w ke pa gen okenn tep wouj ki ekspoze epi ke tout enstalasyon yo byen sere.
• Use a rubber mallet to join tubes. Place a foot on the end to prevent damage to the tube.

IMPORTANT! ENSURE GROUND IS LEVEL. USE GROUND ANCHOR SCREWS ON 4 OUTSIDE LEGS TO SECURE FRAME BEFORE USE

IMPORTANT! ONLY FULLY TIGHTEN BOLTS ONCE FRAME IS ASSEMBLED. FINGER TIGHTEN ONLY DURING ASSEMBLY.

FRONT LEGS: IMPORTANT! LAY PARTS OUT AS SHOWN.
PART NUMBERS ARE PRINTED ON TUBULAR PARTS

TOP SIDE RAILS: IMPORTANT! LAY PARTS OUT AS SHOWN.

BOTTOM SIDE RAILS: IMPORTANT! LAY PARTS OUT AS SHOWN. PART NUMBERS ARE PRINTED ON TUBULAR PARTS

FRONT SUPPORT BAR: IMPORTANT! LAY PARTS OUT AS SHOWN.

MONKEY BARS (MR1800KIT):
IMPORTANT! LAY PARTS OUT AS SHOWN. TWO PEOPLE ARE NOW REQUIRED FOR THE REMAINING ASSEMBLY!

STEP 1: POSITION CARGO NET ONTO LADDER AS SHOWN – NO LOOPS TO BOTTOM

Enpòtan

ONCE ALL BOLTS ARE TIGHTENED ON FRAME, MOVE INTO POSITION. INSTALL PEGS TO HOLD BASE PLATE IN PLACE ONE CORNER AT A TIME, LOOSEN AND LIFT FRAME TO ONE SIDE LEAVING BASE PLATE IN PLACE. SCREW GROUND ANCHOR AND WASHER THROUGH BASE PLATE UNTIL FIRMLY SEATED. LIFT FRAME BACK INTO BASE PLATE AND TIGHTEN. REPEAT ALL 4 CORNERS.

ETAP FINAL:
START AT ONE CORNER OF THE FRAME AND DOUBLE CHECK ALL BOLTS ARE TIGHT. SMALL MOVEMENT IN FRAME IS NORMAL. CONGRATULATIONS! YOU HAVE ASSEMBLED YOUR GROWPLAY COMPACT MONKEY BARS!

FAQ

Q: How often should I inspect the system for maintenance?

A: It is recommended to inspect the system regularly for any signs of damage or wear and tear. Perform a thorough check at least once a month.

K: Kisa mwen ta dwe fè nan ka move tan ekstrèm?

A: During extreme weather conditions like heavy rain or strong winds, take necessary precautions such as covering the system or disconnecting accessories to prevent damage.

Dokiman / Resous

growplay Compact Monkey Bars [pdfManyèl Enstriksyon Compact Monkey Bars, Monkey Bars, Bars

Referans

• Manyèl itilizatè