FlySpark-logo

FlySpark F4 V1 Stack Flight Controller

FlySpark-F4-V1-Stack-Flight-Controller-productEspesifikasyon

  • Non pwodwi:
    FlySpark F4 V1 BLS 60A Stack
  • Karakteristik AI:
    Sensor Fusion, PID Autotuning, Adaptive Filtering
  • Sipò pou lojisyèl:
    Betaflight, INAV, Ardupilot, EMU-flight, SkyBrush
  • ESC Communication:
    BLHeli_S Bluetooth & USB-C
  • Koneksyon:
    3-6S LiPo
  • Dimansyon:
    47.8mm (L) x 47.5mm (W) x 18.3mm (H)
  • Montaj:
    30.5 x 30.5mm ak gwosè twou 4mm
  • Pwa:
    34g

FlySpark-F4-V1-Stack-Flight-Controller-fig-9 FlySpark-F4-V1-Stack-Flight-Controller-fig-10

Enstriksyon Itilizasyon Pwodwi

FlySpark F4 V1 Flight Controller

Layout:
Refer to the user manual for the layout of the flight controller.

Koneksyon periferik:
Connect peripherals as per the provided diagram.

App & FC Configuration:
Use the recommended apps and follow the configuration instructions.

FC Firmware Update:
Connect the flight controller to a PC via USB for firmware updates.

FLYSPARK BLS 60A 4-IN-1 ESC

Layout:
Check the layout guide in the manual for proper installation.

Koneksyon ak motè & kab pouvwa:
Connect motors and power cables securely.

Konfigirasyon ESC:
Use the FlySpark app for ESC configuration settings.

ESC Firmware Update:
Follow the provided steps to update the firmware for ESC.

FlySpark F4 V1 BLS 60A StackFlySpark-F4-V1-Stack-Flight-Controller-fig-1

Espesifikasyon souviewFlySpark-F4-V1-Stack-Flight-Controller-fig-20

FlySpark-F4-V1-Stack-Flight-Controller-fig-2 FlySpark-F4-V1-Stack-Flight-Controller-fig-3

PakeFlySpark-F4-V1-Stack-Flight-Controller-fig-4.1

  • FlySpark F4 V1 Flight Controller x 1
  • FlySpark BLS 60A 4-in-1 ESC x 1
  • 35V 1000uF Low ESR kondansateur x 1
  • M3 Nylon nwa x 4
  • SH 1.0mm 25mm-longè 8pin Kab (pou koneksyon FC-ESC) x 1 SH 1.0mm 75mm-longè 6pin Kab * x 1
  • M3 * 30mm Iner-hexagon Vis x 4
  • DJI 6pin kab (80mm) x 1
  • XT60 pouvwa kab (100mm) x 1

FlySpark-F4-V1-Stack-Flight-Controller-fig-5.2

FC Connection diagramFlySpark-F4-V1-Stack-Flight-Controller-fig-6

Guide to FC & ESC Connections

Metòd 1:

  • Using 8.Pin JST CableFlySpark-F4-V1-Stack-Flight-Controller-fig-7

Metòd 2:

Soudage dirèk

  • Solder 8 wires to the 8 pads on each end, following the pad definitions belowFlySpark-F4-V1-Stack-Flight-Controller-fig-8

Flight controller specs

FlySpark-F4-V1-Stack-Flight-Controller-fig-11.2

  • Sèvi ak 6-pin kab vini ak O3 Air Unit la FlySpark-F4-V1-Stack-Flight-Controller-fig-12.1
  • Use 6-pin cable comes with the FlySpark F4 V1 BLS 60A Stack

FlySpark-F4-V1-Stack-Flight-Controller-fig-13

F C Firmware  update
To update the firmware for your FlySpark F4 VI flight controller, please follow these steps:
Connect the Flight Controller to Your PC:

  • Use a USB cable to connect the FlySpark F4 VI flight controller to your PC

Open Betaflight I INAV Configurator.

  • . Launch the Betaflight Configurator or INAV Configurator on your PC. For this guide, we’ll use Betaflight Configurator as an example.

Navigate to Firmware Flashing:

  • In the Betaflight Configurator, navigate to the ‘Firmware Flashing’ page.

Select Target and Flash Firmware:

  •  Choose the target firmware for ‘Flyspark F4 VI’ from the dropdown menu.
  • Initiate the firmware flashing process.

Nòt:
The Flyspark F4 VI flight controller does not support wireless firmware flashing. It must be  performed using a USB connection to your PC.

FlySpark-F4-V1-Stack-Flight-Controller-fig-14

Flyspark BLS 60A 4-in-l ESCFlySpark-F4-V1-Stack-Flight-Controller-fig-15

Koneksyon ak motè & kab pouvwaFlySpark-F4-V1-Stack-Flight-Controller-fig-16

ESC Specs FlySpark F4 V1 BLS 60A StackFlySpark-F4-V1-Stack-Flight-Controller-fig-17

Mizajou Firmware ESC
This 8-bit 50A ESC comes pre-loaded with BLHeliS firmware but can also be flashed to Bluejay firmware, offering RPM filtering and Bi-directional Dshot support. Follow these steps to update the firmware:

  1. Prepare Your Drone:
    Remove all propellers from your drone for safety.
  2. Connect ESC to Flight Controller:
    Ensure the flight controller is properly connected to the ESC, then power up the drone. This step ensures the ESC initializes correctly.
  3. Konekte ak PC:
    Use a USB Type-C cable to connect the flight controller to your computer.
  4. Access Firmware Configuration:
    Open the Chrome browser and visit: www.esc-configurator.com
  5. Flashing Steps:
    Follow the firmware flashing steps displayed on the configurator website. Ensure you select the appropriate options for flashing to Bluejay firmware.

FlySpark-F4-V1-Stack-Flight-Controller-fig-21

ATANSYON:FlySpark-F4-V1-Stack-Flight-Controller-fig-19

  • PROPELLERS OFF: REMOVE ALL PROPELLERS.
  • SECURE CONNECTION: ENSURE SECURE ESC CONNECTION.
  • FOLLOW STEPS: FOLLOW FLASHING INSTRUCTIONS CAREFULLY.
  • STABLE POWER: ENSURE STABLE POWER SUPPLY.
  • www.FlySpark.in

FAQ

Kouman pou mwen mete ajou firmwèr ESC la?

To update the ESC firmware, follow these steps: 1. Prepare Your Drone: Remove all propellers for safety. 2. Connect ESC to Flight Controller: Ensure proper connection to the ESC and power up.

Dokiman / Resous

FlySpark F4 V1 Stack Flight Controller [pdfManyèl Itilizatè
F4 V1, BLS 60A, F4 V1 Stack Flight Controller, F4 V1, Stack Flight Controller, Flight Controller, Controller

Referans

Kite yon kòmantè

Adrès imel ou p ap pibliye. Jaden obligatwa yo make *