ATMSTACK L2 Smart Z-Axis Modil
Z-aks wotè oto ajisteman enstalasyon manyèl L2-5W/L2-10W/L2-20W/L2-40W
Nòt: Imaj yo se pou referans sèlman, tanpri al gade nan pwodwi aktyèl la. Pou plis enfòmasyon, tanpri eskane kòd QR la.
lis
Metòd enstalasyon aks Z
A5 PRO V2/A10 PRO V2
Devise 4 pcs M4 * 6 nan direksyon goch pou retire kurseur la
Enstale connecteur dédié A5 Pro V2/A10 Pro V2
Sere boulon 4 pcs M4 * 6
A20 PRO V2/A40 PRO V2
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra pa bezwen deplase switch limit yo
Etap 1
- Flip sou graveur la
- Retire 2 vis sou tablo switch limit
- Avanse tablo pi devan pou fè aliman 2 twou
- Fèmen 2 vis tounen nan tablo
- Fini
- Flip sou graveur la
Lazè metòd enstalasyon inifye
Etap: 1 Retire 4 pcs M3 ak kurseur lazè
Etap: 2 Enstale kurseur lazè a ak 4 vis M3 retire nan etap 1
Nòt: Devise moso nan fikse ak tournevis kwa nan bwat zouti an premye, Lè sa a, enstale kurseur lazè nan A48 lazè
Metòd koneksyon kab
Metòd enstalasyon lazè
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral/ A12 Ultral/A24 Ultral/X12 Ultral/ X24 Ultral
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2
Nòt: Lè pouvwa sou yo sèvi ak Z-aks wotè oto ajisteman, ou sèlman bezwen peze "oto konsantre" bouton sou bwat kontwòl oto konsantre lazè a.
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral
Nòt: Ekspozisyon an nesesè lè w sèvi ak Z-aks wotè oto ajisteman, ou bezwen kontwole li nan fen ekspozisyon
- Sèvis Kliyantèl: Pou detay politik garanti, tanpri vizite ofisyèl nou an websit: www.atomstack.com Pou sipò teknik ak sèvis, tanpri imèl: support@atomstack.com
- Manifakti: Shenzhen AtomStack teknoloji co, Ltd
- Adrès: 17th Floor, Building 3A, Phase II, Intelligent Park, No 76, Baohe Avenue, Bip code: tret, Longgang District, Shenzhen, Guangdong, China
- Eskane kòd QR: OSWA lektè kòd/eskanè kòd bar oswa nenpòt aplikasyon ki gen yon eskanè
Dokiman / Resous
 | L2 Smart Z-Axis Modil |
Referans
- Manyèl itilizatèmanual.tools
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Pou konekte a ATMSTACK L2 Smart Z-Axis Modil pou ou A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.
Dapre la Section 05 — Cable connection method for the A20 PRO V2:
If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small tablo adaptè oswa yon Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
Read the full Q&A page
I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
Based on the installation manual for the ATMSTACK L2 Smart Z-Axis Modil, the components you are looking for are part of the cable connection setup (Section 05):
Nòt: If you do not see extra ports, ensure you are looking at the tounen of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.
Read the full Q&A page
I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com pou verifikasyon.
Read the full Q&A page
Now what do I do ?
What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
>
Read the full Q&A page