Entwodiksyon
This manual provides detailed instructions for the operation and maintenance of the NOYAFA NF-468S Network Cable Tester. This device is designed to test various network and telephone cables for continuity, wiring faults, and Power over Ethernet (PoE) functionality.
The NF-468S is a versatile tool for network professionals and enthusiasts, supporting RJ45 (CAT5, CAT5E, CAT6, CAT6A UTP/STP) and RJ11/RJ12 (CAT3) cable types. It features capabilities for detecting shorts, opens, cross pairs, and identifying PoE standards.
Image: The NOYAFA NF-468S Network Cable Tester, showing the main unit and remote unit connected by blue Ethernet cables, ready for testing.
Enfòmasyon sou Sekirite
AVÈTISMAN:
- DO NOT use this tester on live circuits or cables connected to active network devices. Doing so may damage the tester and/or the connected equipment.
- Asire w ke aparèy la etenn lè li pa itilize pou konsève lavi batri a.
- Kenbe aparèy la lwen dlo ak anviwònman ki gen anpil imidite.
- Pa eseye demonte oswa modifye aparèy pou fè tès la. Konfye tout antretyen bay pèsonèl kalifye.
- Jete pil yo selon règleman lokal yo.
Kontni pake
Verifye ke tout atik yo prezan nan pakè ou a:
- 1 x NOYAFA NF-468S Network Tester (Main Unit)
- 1 x Inite Remote
- 1 x 9V Battery (may be included or sold separately)
- 1 x manyèl itilizatè
Image: Contents of the NOYAFA NF-468S package, including the main tester unit, remote unit, 9V battery, and instruction manual.
Pwodwi souview
The NF-468S consists of a main unit and a remote unit. Below is a diagram indicating the key components and interfaces.
Image: Detailed diagram of the NOYAFA NF-468S tester, highlighting its various ports and indicators.
- Remote Unit RJ45/RJ11 Port
- Main Unit RJ45 Port
- Main Unit RJ11 Port
- PoE Test Interface
- Power/Test Mode Switch (QC/OFF/TEST)
- LED Indicators (1-8, G for Ground)
- PoE Result Indicators (D1-D4)
- PoE Power Supply Type Indicators
- Battery Compartment (on back, not visible)
Enstalasyon
1. Enstalasyon batri
The NF-468S requires a 9V battery for operation. To install:
- Jwenn kouvèti konpatiman batri a sou do inite prensipal la.
- Glise oswa deklipe kouvèti a pou ouvri li.
- Connect a 9V battery to the battery clip, observing polarity.
- Mete pil la nan konpatiman an epi fèmen kouvèti a byen fèm.
A low battery indicator will illuminate when the battery needs replacement.
2. Connecting Cables for Testing
Before testing, ensure the cable is disconnected from all active network devices.
- For network cables (RJ45): Connect one end of the cable to the RJ45 port on the main unit and the other end to the RJ45 port on the remote unit.
- For telephone lines (RJ11/RJ12): Connect one end of the cable to the RJ11 port on the main unit and the other end to the RJ11 port on the remote unit.
- For testing wall-mounted LAN cables or patch panels: Connect the main unit to the wall jack/patch panel and the remote unit to the other end of the cable run.
Enstriksyon Operasyon
1. Basic Cable Continuity Test (TEST Mode)
This mode checks for opens, shorts, and miswires in network and telephone cables.
- Connect the cable to be tested between the main unit and the remote unit as described in the Setup section.
- Slide the power switch to the "TEST" position.
- Observe the LED indicators (1-8, G) on both the main and remote units.
- The LEDs will light up sequentially from 1 to 8, then G (Ground).
- Entèpretasyon rezilta yo:
- Koneksyon Nòmal: All LEDs (1-8, G) on both units light up in sequence, indicating a correct wiring scheme.
- Louvri Awondisman: If a specific LED on either the main or remote unit does not light up, it indicates an open circuit (broken wire) for that particular conductor.
- Kout sikwi: If two or more LEDs light up simultaneously, it indicates a short circuit between those conductors.
- Crossed Wires: If the sequence of lighting is different between the main and remote units (e.g., main unit shows 1-2-3, remote shows 1-3-2), it indicates crossed wires.
- Pè fann: This can be harder to detect with simple LED testers. If all LEDs light up correctly but network performance is poor, a split pair might be present. Advanced testers are usually required for definitive split pair detection.
Image: Visual representation of different cable fault indications on the NOYAFA NF-468S, including pass, shielded, miswire, cross-over, open-fault, split pair fault, and PoE test results.
2. QC Function (RJ45 Connector Crimping Test)
This function helps verify the quality of RJ45 connector crimps.
- Connect the RJ45 cable to the main unit's RJ45 port. The remote unit is not needed for this test.
- Slide the power switch to the "QC" position.
- Press the RJ45 connector firmly into the port. The tester will analyze the connection.
- Entèpretasyon rezilta yo:
- Connected Well: All 1-8 lights on the main unit illuminate, indicating a proper crimp.
- Pòv Koneksyon: If some lights (e.g., 2-4) are off, it indicates that the corresponding wire cores are not crimped properly.
Image: The NOYAFA NF-468S performing a QC test on an RJ45 connector, illustrating the difference between a well-connected and a poorly connected crimp.
Image: Step-by-step guide for using the RJ45-RJ11 plug tester's QC function on the NOYAFA NF-468S, demonstrating how to check for crimp errors.
3. PoE Test
The NF-468S can identify Power over Ethernet (PoE) devices and detect PoE standards.
- Connect the network cable from the PoE source (e.g., PoE switch) to the "PoE" port on the main unit. The remote unit is not required.
- Slide the power switch to the "TEST" position.
- Observe the PoE result indicators (D1-D4) and the PoE power supply type indicators.
- Entèpretasyon rezilta yo:
- The indicators will show if PoE is present and identify the power supply method (e.g., End-span (1/2, 3/6), Mid-span (4/5, 7/8), or 8-core power supply).
- It also indicates compliance with IEEE 802.3AF or IEEE 802.3AT standards, or if it's a non-standard PoE.
Image: The NOYAFA NF-468S connected to a network rack, demonstrating its PoE testing capabilities and displaying the results of the PoE power supply type and situation.
4. Cable Length Test (Approximate)
The NF-468S can provide an approximate cable length measurement for telephone lines up to 2000 meters.
- Connect one end of the telephone line (RJ11/RJ12) to the main unit's RJ11 port. The remote unit is not needed.
- Slide the power switch to the "TEST" position.
- The tester will display an approximate length. Note that this is an estimation and may vary based on cable quality and type.
Image: The NOYAFA NF-468S testing a wall-mounted LAN cable, illustrating its capability to measure cable length for Ethernet and LAN connections within a range of 2.5 to 2000 meters.
Antretyen
- Netwayaj: Use a soft, dry cloth to clean the exterior of the tester. Do not use abrasive cleaners or solvents.
- Depo: Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. If storing for extended periods, remove the battery to prevent leakage.
- Ranplasman batri: Replace the 9V battery when the low battery indicator illuminates to ensure accurate readings.
Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Tèstè a pa limen. | Batri ki mouri oswa mal enstale. | Check battery installation. Replace with a new 9V battery. |
| LEDs do not light up or show incorrect sequence. | Cable fault (open, short, miswire, cross). | Refer to "Operating Instructions" for LED interpretation. Re-terminate or replace the cable. |
| Inaccurate PoE test results. | Cable connected to a non-PoE port or device. | Ensure the cable is connected to a PoE-enabled port. Verify the PoE source is active. |
| Tester damaged after use. | Used on a live circuit. | The tester is not designed for live circuits. Contact customer support for repair or replacement options. |
Espesifikasyon
- Modèl: NF-468S
- Kalite kab sipòte: RJ45 (CAT5, CAT5E, CAT6, CAT6A UTP/STP), RJ11/RJ12 (CAT3)
- Fonksyon tès: Continuity (opens, shorts, miswires, cross pairs), PoE detection (802.3af/at, non-standard), RJ45 crimp quality (QC function), Approximate cable length (telephone line up to 2000m).
- PoE Voltage Pwoteksyon: Up to 60V anti-burnout
- Sous pouvwa: 9V batri
- Dimansyon: Approximately 6.65 x 4.61 x 1.34 inches (Main Unit)
- Pwa: Apeprè 7.37 ons
- Sètifikasyon: CE, FCC, ISO 9001, RoHS
Garanti ak sipò
Enfòmasyon sou Garanti
NOYAFA products are designed and manufactured to high-quality standards. This product comes with a standard manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty card included in your package or visit the official NOYAFA websit la pou wè tèm ak kondisyon garanti espesifik yo.
Sipò pou Kliyan
If you encounter any problems during use, or have questions regarding the NOYAFA NF-468S Network Cable Tester, please contact NOYAFA customer support. Our team is available to assist you with technical support and troubleshooting.
Pou sipò, tanpri vizite NOYAFA Store on Amazon oubyen gade enfòmasyon kontak ki nan anbalaj pwodwi w la.
