1. Entwodiksyon
The Matek Mateksys AP_PERIPH CAN-L4-BM is an ultra-precise digital power monitor designed for applications requiring accurate current and voltage measurements via the CAN bus. It utilizes the TI INA239 IC and runs ArduPilot AP_Periph firmware, supporting the CAN/DroneCAN protocol. This device provides reliable power monitoring without the need for calibration.
2. Karakteristik
- Ultra-precise digital power monitoring.
- Based on TI INA239 and ArduPilot AP_Periph firmware.
- Supports CAN/DroneCAN protocol.
- No calibration required for accurate current and bus voltage readouts.
- Low power loss due to 200µΩ typical conductive path resistance.
3. Espesifikasyon
- MCU: STM32L431xC, memwa Flash 256KB
- Power Monitor IC: INA239 (85-V, 16-Bit, High-Precision)
- Batri Voltage Sense Input: 0 ~ 85V
- Current Sense Range: 0 ~ 204.8A
- Load Current on Sensing Resistor: 150A (Continuous), 204.8A (Burst)
- Voltage Presizyon: 0.1%
- Aktyèl Presizyon: 2%
- Entèfas: CAN (DroneCAN Protocol), UART2 (spare, DFU), ST debug (SWCLK & SWDIO)
- Pwovizyon pou pouvwa: 4.5 ~ 5.5V @ 5V pad/pin
- Konsomasyon pouvwa: 10mA
- Tanperati operasyon: -40 ~ 85 °C
- Gwosè tablo: 30mm x 22mm x 3mm
- Pwa: 4g
- Firmware: ArduPilot AP_Periph (Update via DroneCAN GUI Tool)
4. Pwodwi souview
Layout eleman
5. Enstalasyon ak Enstalasyon
Enstriksyon fil elektrik
Proper wiring is crucial for accurate readings and safe operation of the CAN-L4-BM.
General Wiring Tips
- Solder the positive wires as close as possible to both sides of the current sensing resistor on the board for optimal accuracy.
- Ensure a common ground connection between the flight controller and the ESC/Load to prevent ground loops and ensure stable operation.
- If CAN wires are excessively long, bridge the 120R jumper on the CAN-L4-BM board to maintain signal integrity.
- The large pad on the bottom side of the board is a dead pad and has no circuit network; it can be used for structural support if needed.
- The two mounting ears can be carefully cut off if not required for installation in space-constrained environments.
Konfigirasyon mikrolojisyèl
The CAN-L4-BM runs ArduPilot AP_Periph firmware. Configuration is performed via the DroneCAN protocol through your flight controller's settings.
- Connect the CAN-L4-BM to your flight controller's CAN bus port.
- Set the appropriate parameter in your flight controller's firmware to enable the CAN driver:
- For CAN bus1:
CAN_P1_DRIVER = 1 - For CAN bus2:
CAN_P2_DRIVER = 1
- For CAN bus1:
- Configure battery monitoring by setting:
BATTx_MONITOR = 8(DroneCAN-BatteryInfo), where 'x' corresponds to the battery monitor instance you are configuring. - Firmware updates for the CAN-L4-BM can be performed using the DroneCAN GUI Tool.
6. Operasyon
Endikatè ki ap dirije
- LED ble (kliyote rapid): Indicates the board is in the process of booting up.
- LED ble (kliyote dousman): Indicates the board is working correctly and communicating via CAN.
- Wouj ki ap dirije: Indicates that 3.3V power is present on the board.
Done Siveyans
Once properly configured and powered, the flight controller will receive accurate current and bus voltage data from the CAN-L4-BM via the DroneCAN bus. This data can be logged and monitored through your flight controller's telemetry system or compatible ground station software.
7. Antretyen ak pi bon pratik yo
- Regularly inspect all soldered connections for integrity and signs of wear or corrosion.
- Keep the board free from dust, moisture, and debris to ensure optimal performance and longevity.
- Ensure proper ventilation if operating the device in enclosed spaces, although the CAN-L4-BM has a wide operating temperature range.
- Avoid exposing the board to extreme environmental conditions (e.g., excessive humidity, direct water contact) beyond its specified operating range.
NAN. Depanaj
Pwoblèm komen
- No data from monitor:
- Verify all CAN bus connections (CAN-H, CAN-L, GND, 5V) are secure and correct.
- Check the LED indicators for proper boot and operation (a slow blue blink indicates normal function).
- Asire w
CAN_P1_DRIVERorCAN_P2_DRIVERis set correctly in the flight controller parameters. - Konfime sa
BATTx_MONITOR = 8is set for the correct battery monitor instance. - Check for any short circuits or incorrect voltage supply to the CAN-L4-BM board.
- Lekti ki pa egzak:
- Ensure positive wires are soldered as close as possible to the current sensing resistor on the board.
- Verify common ground connections between all components in the power system.
- Check for any physical damage to the board or its components that might affect sensor accuracy.
- Kat la pa limen:
- Confirm that a stable 4.5~5.5V supply is provided to the 5V pad/pin.
- Check the Red 3.3V indicator LED; if it's off, there might be a power issue.
- Inspect all power supply wiring for breaks or incorrect connections.
9. Kontakte ak Sipò
For further assistance, technical support, or to access additional resources, please refer to the official Mateksys documentation available on their website or consult relevant community forums for ArduPilot and DroneCAN users.
