Pro-Ject Debut EVO 2 Turntable Instruction Manual

1. Entwodiksyon

Thank you for choosing the Pro-Ject Debut EVO 2 Turntable. This high-fidelity record player is crafted in Europe by hand, offering an enhanced listening experience. It features a heavy platter, a carbon fiber tonearm with a resonance-damping aluminum bearing block, and an adaptive anti-skating system. The turntable comes pre-mounted with a Pick it MM EVO Moving Magnet Phono Cartridge and includes a DC/AC power generator. This manual provides essential information for setting up, operating, and maintaining your turntable to ensure optimal performance and longevity.

2. Pake kontni

Tanpri asire w ke tout atik sa yo enkli nan pakè w la:

• Pro-Ject Debut EVO 2 Turntable Unit
• Pick it MM EVO Moving Magnet Phono Cartridge (pre-mounted)
• 15V DC 0.8A Power Supply
• Kouvèti Pousyè
• 7'' Singles Adapter
• Kondwi Belt
• Kontrepwa
• Pwa anti-paten

3. Enstriksyon Enstalasyon

Follow these steps carefully to set up your Pro-Ject Debut EVO 2 Turntable.

3.1 Debalaj ak plasman

Retire tout konpozan yo nan anbalaj la avèk prekosyon. Mete platin nan sou yon sifas ki estab e plat, lwen limyè solèy dirèk, sous chalè ak vibrasyon.

3.2 Platter and Drive Belt Installation

1. Place the main platter onto the central spindle.
2. Carefully loop the drive belt around the motor pulley and the inner rim of the platter. Ensure the belt is not twisted.

3.3 Tonearm and Cartridge Setup

1. Slide the counterweight onto the rear of the tonearm with the numbers facing forward.
2. The Pick it MM EVO cartridge is pre-mounted on the headshell. Attach the headshell to the tonearm and tighten the locking nut securely.
3. Carefully remove the stylus protector from the cartridge.
4. Unlock the tonearm from its rest. Lift the cueing lever.
5. While holding the headshell, lower the cueing lever completely. Do not let the stylus touch the platter.
6. Turn the counterweight until the tonearm floats parallel to the platter. This is the balanced position.
7. Once balanced, return the tonearm to its rest and lock it.
8. Turn only the numbered ring of the counterweight to '0' on the center line. Do not turn the entire counterweight.
9. Now, turn the entire counterweight (including the numbered ring) counter-clockwise until the desired tracking force is set (e.g., 2 grams for the Pick it MM EVO cartridge).
10. Locate the anti-skating dial near the tonearm base. Set this dial to the same value as your tracking force (e.g., '2').

3.4 Dust Cover and Connections

1. Attach the dust cover hinges to the turntable chassis and then carefully place the dust cover onto the hinges.
2. Connect the turntable's RCA output cables to your amplifier's phono input (or a separate phono preamplifier).
3. Connect the ground wire from the turntable to your amptèminal tè lifier a.
4. Plug the 15V DC 0.8A power supply into the turntable and then into a wall outlet.

3.5 Videyo Enstalasyon

For a visual guide on the initial setup, please watch the following video:

4. Operasyon Enstriksyon

4.1 Jwe yon Disk

1. Mete yon dosye sou plato a.
2. Select the correct playback speed (33 or 45 RPM) using the speed selector switch.
3. Unlock the tonearm and lift it using the cueing lever.
4. Pozisyone stylus la ak anpil atansyon sou rainur ou vle a sou disk la.
5. Desann levye repè a dousman pou pèmèt stylet la desann sou disk la.

4.2 Kijan pou kanpe lekti a

1. Leve bra ton an avèk levye repèkaj la.
2. Return the tonearm to its rest and lock it in place.
3. Remove the record from the platter.
4. Turn off the turntable using the power switch.

5. Antretyen

5.1 Netwaye Stylus la

Use a soft stylus brush to gently clean the stylus from back to front. Never brush from front to back, as this can damage the stylus.

5.2 Netwaye platin an

Wipe the dust cover and plinth with a soft, dry, anti-static cloth. Avoid using abrasive cleaners or solvents.

5.3 Drive Belt Inspection

Periodically inspect the drive belt for any signs of wear or stretching. A worn belt can affect playback speed and consistency.

NAN. Depanaj

If you encounter any issues with your turntable, please refer to the following common solutions:

• Pa gen son: Check all cable connections (RCA, ground, power). Ensure your amplifier is set to the correct input and volume.
• Son defòme: Verify that the tracking force and anti-skating settings are correct. Ensure the stylus is clean and undamaged.
• Vitès ki pa kòrèk: Confirm the drive belt is properly seated and not worn. Ensure the correct speed (33/45 RPM) is selected.
• Bwi ron: Check the ground wire connection. Ensure the turntable is placed away from electronic devices that may cause interference.

If problems persist, please contact Pro-Ject customer support.

7. Espesifikasyon

8. Garanti ak sipò

For warranty information and technical support, please refer to the documentation included with your product or visit the official Pro-Ject Audio Systems websit la. Kenbe prèv acha ou a pou nenpòt reklamasyon garanti.