Entwodiksyon
This manual provides instructions for the installation, operation, and maintenance of the Olympia D-820T Overflow and Waste Drain Trim Kit. This kit is designed to enhance the functionality and appearance of your bathtub drain system. Please read these instructions thoroughly before beginning installation or use.
Pwodwi souview
The Olympia D-820T Trim Kit includes the following components:
- Overflow Snap-In Cap (Chrome finish)
- Push & Pull Strainer Group (Chrome finish)
This trim kit is specifically designed for use with Olympia D-820R-PVC and D-820RS-PVC drain bodies. The overflow cap design doubles the overflow drain capacity compared to traditional screw-face plates.
Image: The Olympia D-820T Overflow and Waste Drain Trim Kit, showing the chrome overflow snap-in cap (top) and the chrome push & pull strainer (bottom).
Enstalasyon ak Enstalasyon
This trim kit is intended to be installed over an existing compatible Olympia D-820R-PVC or D-820RS-PVC drain body. Ensure you have the correct drain body before proceeding.
- Prepare beny lan: Ensure the bathtub is clean and free of debris around the overflow and drain openings.
- Install Overflow Snap-In Cap: Align the overflow snap-in cap with the overflow opening on the bathtub. Press firmly until the cap snaps securely into place over the existing overflow drain body. Ensure a tight fit to prevent leaks.
- Install Push & Pull Strainer: Insert the push & pull strainer into the main drain opening. The strainer is designed to fit into the existing drain body. Ensure the rubber gasket on the strainer creates a seal with the drain opening. Some minor adjustments or a rubber mallet may be needed for a snug fit. Do not overtighten or force components excessively.
- Tès pou Fuites: Fill the bathtub with water and check both the overflow and main drain for any signs of leakage. Operate the push & pull strainer several times to ensure proper sealing and drainage.
Si ou pa sèten sou nenpòt etap nan pwosesis enstalasyon an, li rekòmande pou ou konsilte yon plonbye kalifye.
Operasyon
The D-820T Trim Kit features a push & pull strainer for controlling water drainage.
- Pou fèmen drenaj la: Press down firmly on the top of the strainer. This will seal the drain, allowing the bathtub to fill with water.
- Pou ouvri drenaj la: Pull up on the top of the strainer. This will unseal the drain, allowing water to flow out.
The overflow snap-in cap functions automatically to prevent the bathtub from overflowing by directing excess water into the drain system.
Antretyen
Regular cleaning will help maintain the appearance and functionality of your Olympia D-820T Trim Kit.
- Netwayaj: Use a soft cloth and mild, non-abrasive cleaner specifically designed for chrome finishes. Avoid harsh chemicals, abrasive cleaners, or scouring pads, as these can damage the finish.
- Enspeksyon regilye: Periodically check the strainer and overflow cap for any buildup of hair or debris that might impede drainage. Clean as necessary.
- Gasket Check: Ensure the rubber gasket on the push & pull strainer remains intact and provides a good seal. Replace if worn or damaged.
Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Strainer does not seal properly / Bathtub drains slowly. | Debris under the strainer gasket; worn gasket; improper installation. | Remove strainer and clean gasket and drain opening. Check gasket for damage and replace if necessary. Re-install strainer ensuring a snug fit. |
| Overflow cap is loose or leaks. | Improper snap-in installation; damaged overflow cap. | Ensure the overflow cap is fully snapped into place. Inspect for damage and replace if needed. |
| Trim kit does not fit the existing drain. | Incompatible drain body; incorrect model purchased. | Verify that your existing drain body is an Olympia D-820R-PVC or D-820RS-PVC. This trim kit is designed specifically for these models. Contact Olympia support for compatibility questions. |
Espesifikasyon
- Modèl: D-820T
- Mak: Olympia
- Materyèl: Metal
- Koulè: Chrome
- Pwa atik: 6.7 ons
- Dimansyon pake: 4.53 x 4.21 x 3.23 pous
- Konpatibilite: Designed for Olympia D-820R-PVC & D-820RS-PVC drain bodies.
Garanti ak sipò
For warranty information or technical support regarding your Olympia D-820T Overflow and Waste Drain Trim Kit, please refer to the official Olympia websit la oubyen kontakte depatman sèvis kliyan yo. Kenbe resi acha w la pou reklamasyon garanti.
Olympia Customer Service: Tanpri vizite the Olympia Store on Amazon or the official Olympia websit pou detay kontak.
