Entwodiksyon
Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.
Enfòmasyon enpòtan sou sekirite
Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.
- Verify that your monitor's weight and VESA pattern are within the specified limits.
- Do not exceed the maximum load capacity of 26.5 lbs per arm.
- Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
- Use only the provided hardware.
- Kenbe ti pati yo lwen timoun yo.
Espesifikasyon
- Modèl: EGCM13B
- Konpatibilite gwosè ekran: 13 a 34 pous
- Weight Capacity (per arm): Jiska 26.5 liv
- VESA konpatibilite: 75x75 milimèt, 100x100 milimèt
- Arm Span: 33 pous
- Wotè poto: 16.3 pous
- Kalite mouvman: Tilt, Swivel, Rotation, Articulating
- Maksimòm ang enklinezon: 90 Degre
- Materyèl: Alloy Steel
- Koulè: Nwa
- Kalite montaj: Mòn tab (C-Cl)amp oswa Grommet)
- C-Clamp Epesè biwo: 0.39" - 3.15"
- Grommet Mount Desk Thickness: 0.39" - 2.17"
- Dyamèt twou Grommet: 0.47" - 0.79"
Kontni pake
Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.
- Poto prensipal ak biwo Clamp/Grommet Base
- Doub monitè bra
- VESA Plates (2x)
- Mounting Hardware (screws, washers, tools)
- Klip Jesyon Kab
- Manyèl Enstriksyon
Enstalasyon ak Enstalasyon
1. Verifikasyon Konpatibilite Biwo a
Before installation, ensure your desk meets the following criteria:
- Materyèl: Recommended for wooden tables.
- Anba: Preferably free of beams or panels that may interfere with installation.
- C-Clamp Epesè: 0.39" - 3.15"
- Grommet Mount Thickness: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")
2. Monitor Compatibility Check
Each monitor must meet these conditions:
- Gwosè ekran: 13 a 34 pous
- Pwa: Jiska 26.5 liv
- Twou Montaj VESA: 75x75 mm or 100x100 mm apart on the back of the monitor.
3. Assemble the Pole with Clamp Sipò
Choose either C-Clamp or Grommet installation based on your desk type.
Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.
4. Assemble the Arm and Pole Wire Clips
Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.
5. Assemble VESA Plate and Monitor
Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.
6. Install the Monitor to the Swivel Arm
Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).
Operasyon ak Ajisteman
The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewkonfò:
- Ajisteman wotè: Dekole cl laamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp an sekirite.
- Enklinezon: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
- Swivel: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewsoti nan diferan ang.
- Wotasyon: Vire monitè a 360 degre pou chanje ant oryantasyon peyizaj ak pòtrè.
- Arm Extension/Retraction: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.
Antretyen
- Tcheke tout vis ak koneksyon yo detanzantan pou asire yo rete sere epi byen fèm.
- Netwaye montaj la ak yon twal mou.amp twal. Evite pwodui netwayaj abrazif.
- Do not disassemble the mount unless instructed to do so.
Depanaj
- Monitè yo pa nivo: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
- Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
- Mòn nan santi l enstab: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.
Garanti ak sipò
For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.
