Entwodiksyon
Thank you for choosing the Fockety Paraffin Wax Machine. This device is designed to provide a soothing and moisturizing paraffin wax treatment for your hands, feet, and elbows. Regular use can help soften dry skin and provide relaxation. Please read this manual thoroughly before operating the machine to ensure safe and effective use.
Prekosyon Sekirite Enpòtan
- Always unplug the machine from the power outlet when not in use, before cleaning, or before adding/removing wax.
- Pa plonje machin nan nan dlo oswa nan nenpòt lòt likid.
- Kenbe soti nan atenn timoun yo.
- Pa sèvi ak machin nan si kòd kouran an oswa ploge a domaje.
- Asire w ke machin nan mete sou yon sifas ki estab e ki reziste chalè.
- Do not add water or other liquids to the wax pot. Only use paraffin wax specifically designed for paraffin baths.
- The wax will be hot. Always check the wax temperature before dipping hands or feet to avoid burns. The melting temperature of the wax is around 70 to 80℃. Allow it to cool to a comfortable temperature before use.
- Do not use on broken, irritated, or sensitive skin. Consult a doctor if you have any skin conditions or circulatory problems.
- Use the provided heat insulation board to prevent direct contact with the hot bottom of the pot.
Kontni pake
Tanpri verifye pake a pou asire w ke tout atik yo la:
- 1 x Paraffin Wax Machine Host
- 1 x kouvèti
- 1 x manyèl itilizatè
- 1 x Heat Insulation Board
Pwodwi souview
Familiarize yourself with the components of your Fockety Paraffin Wax Machine:
- Maritim: The internal aluminum alloy pot where the paraffin wax is melted. Designed for constant temperature melting.
- Kouvèti: Covers the wax pot to retain heat and prevent contamination.
- Kòd pouvwa: Connects the machine to the electrical outlet.
- Limyè Endikatè: Illuminates to show the machine's operational status.
- Bouton Chanjman: Controls the power (On/Off) and heating settings.
- Heat Insulation Board: A separate board placed at the bottom of the wax pot to prevent direct contact with the hot surface and provide anti-scalding protection.
Enstalasyon
- Plasman: Place the paraffin wax machine on a flat, stable, and heat-resistant surface. Ensure it is away from water sources and flammable materials.
- Insert Heat Insulation Board: Place the heat insulation board at the bottom of the aluminum alloy liner inside the machine. This is crucial for safety.
- Add Paraffin Wax: Cut the paraffin wax block into small pieces or break it into smaller chunks. Place the wax into the aluminum alloy liner. Do not add water.
- Wax Level: Ensure the wax level is between the "Highest wax level" and "Lowest wax level" marks indicated inside the liner.
- Konekte pouvwa: Plug the power cord into a standard 110V US electrical outlet.
Enstriksyon Operasyon
Follow these steps for a safe and effective paraffin wax treatment:
- Limen: Rotate the switch knob from '0' (Off state) to '1' (On state). The indicator light will illuminate, signifying that the machine is heating.
- Fonn sir: Allow approximately 10 minutes for the wax to fully melt. You may add a few drops of essential oil to the melted wax to increase lubricity, if desired.
- Dekonekte epi refwadi: Once the wax is completely melted, unplug the power supply. This allows the wax to cool slightly to a safe and comfortable temperature for dipping. Ensure the heat insulation board is in place to prevent burns from the bottom of the pot.
- Tcheke Tanperati: Before dipping, test the wax temperature on a small area of your skin (e.g., wrist) to ensure it is comfortable and not too hot.
- Dip Hands/Feet: When the temperature is suitable, slowly dip your hand or foot into the wax for about 5 seconds. Remove and allow the wax to solidify slightly. Repeat this process approximately 5 times to build up a thick layer of wax. If you cannot soak, you can use a brush to apply the wax.
- Gloves (Optional): For easier peeling, you may put on disposable gloves or cotton gloves over the waxed area.
- Rilaks: Allow the wax to remain on your skin for about 10 minutes to maximize moisturizing and softening effects.
- Remove Wax: Gently peel off the wax. The removed wax can be placed back into the pot for reuse (can be used repeatedly 25-30 times).
Antretyen
- Netwayaj: After use, allow the remaining wax to cool and solidify. Once solid, you can usually lift the entire block of wax out of the liner. If necessary, gently scrape any remaining wax from the liner using a non-abrasive tool.
- Netwayaj eksteryè: Siye eksteryè machin nan ak yon mou, damp twal. Pa sèvi ak pwodui netwayaj abrazif oswa plonje aparèy la nan dlo.
- Depo: Sere machin nan yon kote ki fre, sèk lè li pa itilize.
Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Machin pa vire sou. | Pa branche; switch kouran an etenn; kouran koupetage. | Ensure the power cord is securely plugged into a working outlet. Turn the switch knob to '1'. Check your household's power supply. |
| Wax is not melting. | Machine not on; insufficient heating time. | Confirm the machine is turned on and the indicator light is active. Allow sufficient time (approx. 10 minutes) for the wax to melt completely. |
| Wax is too hot. | Insufficient cooling time after melting. | Unplug the machine and allow the wax to cool down to a comfortable temperature before use. Always test the temperature before dipping. |
Espesifikasyon
- Mak: Fockety
- Modèl: Focketyk7v02eib84-11
- Materyèl: ABS (body), Aluminum Alloy (liner)
- Koulè: White (machine body), Purple (lid)
- Kapasite: 2.3 lit
- Antre Voltage: 110V (US Plug)
- Tanperati k ap fonn: Approximately 70-80℃ (after heating)
- Dimansyon pake: 15.2 x 10.8 x 8.1 pous
- Pwa atik: 2.35 liv
Garanti ak sipò
For any questions, concerns, or support regarding your Fockety Paraffin Wax Machine, please contact the manufacturer or your retailer. Refer to your purchase documentation for specific warranty details and contact information.
