1. Pwodwi souview
This manual provides essential information for the safe and efficient operation of your KATOOL KT-T900 Automatic Hydraulic Tire Changer and KT-B750 Automatic Measurement Ruler Wheel Balancer Combo. Please read all instructions carefully before use.
Figure 1: KATOOL KT-T900 Tire Changer and KT-B750 Wheel Balancer Combo.
Karakteristik kle:
- KT-T900 Tire Changer: Fully hydraulic power system, built-in top assist arm, leverless design, stainless steel mounting head with plastic cover, assist wheel lift device, high-quality motor with pure copper winding.
- KT-B750 Wheel Balancer: Automatic measurement ruler for A and D values, robust 3mm thick steel body, all-in-one pressure sensor support design, top-level motor with pure copper winding, φ36mm shaft thread with quenching treatment, advanced welding technology computer board, various balance modes, built-in fault diagnosis and self-calibration, unit selection (Ounce/Gram, MM/Inch).
2. Enstalasyon
2.1 Debalaj ak enspeksyon
Carefully unpack all components. Inspect for any shipping damage. Report any damage to the carrier immediately.
2.2 Asanble
While the wheel balancer requires minimal assembly, ensure all components are securely fastened. The tire changer requires assembly of its various arms and components. Refer to the included assembly diagrams for detailed steps.
2.3 Koneksyon kouran ak lè
- KT-T900 Tire Changer: Connect to a 110V / 1PH / 60HZ power supply. Connect to an air compressor providing 0.8-1.0Mpa (116-145psi) air pressure.
- KT-B750 Wheel Balancer: Connect to a 120V 1PH power supply.
- Ensure all air hoses are securely connected and free of leaks. It is recommended to replace standard hose clamps with more robust alternatives if necessary to prevent leaks under pressure.
2.4 Placement and Securing
Position both machines on a level, stable surface. For optimal performance and safety, the KT-B750 Wheel Balancer should be bolted to the floor to prevent movement and ensure accurate measurements during operation.
3. Operating Instructions - KATOOL KT-T900 Tire Changer
The KT-T900 is designed for efficient and safe tire changing with its automatic hydraulic system.
Figure 2: KT-T900 Tire Changer demonstrating hydraulic arm movement.
3.1 Mounting and Demounting Tires
- Pozisyonman wou a: Place the wheel onto the turntable. The wheel clamp can accommodate sizes from 12" to 30".
- Clampap vire wou a: Use the foot pedals to activate the rim clamps, byen fikse volan an nan platin lan.
- Kase pèl: Utilize the bead breaker arm to separate the tire beads from the rim. The hydraulic system ensures powerful and controlled operation.
- Mounting/Demounting Head: Position the stainless steel mounting head (with plastic cover to protect rims) at the edge of the tire. The leverless design simplifies the process.
- Using the Assist Arm: For difficult tires, such as run-flat or low-profile, engage the built-in top assist arm to help hold the tire bead in place.
- Wotasyon: Use the foot pedal to rotate the turntable, allowing the mounting head to smoothly remove or install the tire.
- Inflation (Bead Blaster): For stubborn beads, the integrated bead blaster can be used to quickly seat the tire. Ensure proper safety precautions are followed.
Video 1: KATOOL AK-T900 Tire Changer in operation.
Video 2: Demonstration of a similar tire changer's bead blaster functionality.
4. Operating Instructions - KATOOL KT-B750 Wheel Balancer
The KT-B750 provides precise wheel balancing with its automatic measurement ruler and various balancing modes.
Figure 3: KT-B750 Wheel Balancer control panel and wheel mounting.
4.1 Monte wou a
- Ensure the balancer is powered on.
- Mount the wheel securely onto the balancer's shaft. Use appropriate cones and a quick-release nut to center and hold the wheel.
4.2 Inputting Wheel Dimensions
- Use the automatic measurement ruler to input the 'A' (distance from machine to rim) and 'D' (rim diameter) values. The ruler will automatically detect and display these values on the control panel.
- Manually input the 'W' (wheel width) value using the control panel buttons.
- Select the desired balancing mode (e.g., Dynamic for clip-on weights on both sides, Static for single-plane balancing) using the control panel.
4.3 Balancing Process
- Close the wheel guard (if equipped) and press the START button. The machine will spin the wheel to measure imbalance.
- The display will show the required weight amounts and their positions (indicated by the laser pointer).
- Apply the indicated weights to the inner and/or outer edges of the rim as directed.
- Spin the wheel again to verify the balance. Repeat the process if necessary until the display shows zero or minimal imbalance.
Video 3: Demonstration of a similar wheel balancer's operation.
5. Antretyen
Antretyen regilye asire lonjevite ak pèfòmans optimal ekipman KATOOL ou a.
5.1 Netwayaj jeneral
- Keep both machines clean and free of dirt, dust, and tire debris.
- Siye sifas ak anonsamp cloth. Avoid using harsh chemicals that may damage finishes or electronic components.
5.2 Lubrification
- Tire Changer: Periodically lubricate moving parts, such as the assist arm joints and clamping mechanisms, according to the manufacturer's recommendations.
- Sistèm lè: Ensure the air filter/regulator unit (if present) is regularly oiled. The instruction label on the unit advises frequent oiling to the oil cup and to release water.
5.3 Air System Inspection
- Regularly check all air hoses and connections for leaks. Replace any worn or damaged hoses and ensure clamps yo an sekirite.
- Monitor the air pressure gauge to ensure it operates within the specified range.
NAN. Depanaj
Seksyon sa a adrese pwoblèm komen ou ka rankontre.
6.1 Tire Changer Issues
- Difficulty with Bead Breaking/Mounting: Ensure proper lubrication of tire beads. Verify adequate air pressure to the machine. Utilize the assist arm for low-profile or stiff tires.
- Fuite lè: Inspect all pneumatic connections, especially hose clamps. Replace any damaged hoses or fittings.
6.2 Wheel Balancer Issues
- Lekti ki pa kòrèk: Ensure the machine is bolted securely to a level floor. Verify correct input of wheel dimensions (A, D, W). Perform the self-calibration program if readings are consistently off.
- Machin nan pa kòmanse: Check power connections and ensure the power switch is on.
7. Espesifikasyon
KATOOL KT-T900 Automatic Hydraulic Tire Changer
| Spesifikasyon | Valè |
|---|---|
| Dyamèt maksimòm wou | 47" / 1200 milimèt |
| Max Wheel Width | 16" / 406 milimèt |
| Rou Clamp | 12"-30" |
| Pwovizyon pou pouvwa | 110V / 1PH / 60HZ |
| Gear Box Motor Power | 1.5KW / 2HP |
| Pouvwa idwolik | 1.1KW / 1.5HP |
| Vitès wotasyon | 6.8 r / min |
| Presyon lè | 0.8-1.0Mpa (116-145psi) |
| Pwa nèt | 188KG / 414 lbs |
KATOOL KT-B750 Automatic Measurement Ruler Wheel Balancer
| Spesifikasyon | Valè |
|---|---|
| Dyamèt Rim | <30" |
| Lajè wou | 3"-12" |
| Dyamèt wou | <880mm |
| Balanse vitès | 180rpm |
| Pwovizyon pou pouvwa | 120V 1PH |
| Pouvwa motè | 0.25KW |
| Rim Center Hole Dia. | <135mm |
| Pwa wou | <65KG |
| Balancing Accuracy | ± 1g |
| Mezire tan | 7S |
Enfòmasyon jeneral sou pwodwi
- Manifakti: KATOOL
- Modèl: KT-T900+KT-B750
- Pwa atik: 622 liv
- Dimansyon pwodwi: 53 x 36 x 60 pous
8. Garanti ak sipò
Your KATOOL product is supported by the manufacturer and seller.
- Règleman retounen: This product is returnable until January 31, 2026.
- Sipò Kliyan: Pou nenpòt kesyon oswa asistans, tanpri kontakte sèvis kliyan.
- Manifakti: KATOOL
- Vandè: Rainier Engineering, LTD
