Entwodiksyon
This user manual provides comprehensive instructions for the installation, operation, and maintenance of your InSinkErator FHC3010 Modern Hot and Cold Water Dispenser. Please read this manual thoroughly before installation and use to ensure safe and efficient operation of your appliance. Keep this manual for future reference.
Pwodwi souview
The InSinkErator FHC3010 is a modern hot and cold water dispenser designed for convenience and efficiency in your kitchen. It provides instant access to near-boiling water and filtered cold water directly from your sink.
Figure 1: InSinkErator FHC3010 Hot and Cold Water Dispenser in Matte Black finish.
Karakteristik kle:
- Modern design with Matte Black finish.
- Dedicated faucet for instant hot and cold water.
- Provides near-boiling water (up to 200°F) for hot beverages and cooking.
- Delivers filtered cold water.
- Easy-to-use dual handles for precise temperature control.
- Under-sink installation for a clean countertop appearance.
Enstalasyon
Proper installation is crucial for the performance and safety of your water dispenser. It is recommended that installation be performed by a qualified plumber.
Anvan ou kòmanse:
- Ensure you have all necessary tools and components as listed in the packaging.
- Verify that your electrical outlet meets the product's power requirements (Corded Electric).
- Confirm adequate space under the sink for the dispenser tank and connections.
- Fèmen prensipal ekipman pou dlo ki mennen nan lavabo kwizin ou an.
Etap enstalasyon:
- Prepare the Sink Hole: If a hole is not pre-drilled, create a 1-3/8 inch (3.5 cm) diameter hole in your sink or countertop.
- Monte tiyo a: Insert the faucet shank through the sink hole. Secure it from underneath with the provided mounting hardware.
- Konekte Tiyo Dlo yo: Connect the hot and cold water supply lines to the appropriate inlets on the dispenser faucet. Ensure all connections are tight to prevent leaks.
- Install the Tank: Position the hot water tank securely under the sink. Connect the tank's outlet to the faucet's hot water inlet.
- Koneksyon elektrik: Plug the dispenser's power cord into a grounded electrical outlet.
- Netwaye sistèm nan: Before heating, open the hot water handle on the dispenser and allow water to flow until it runs smoothly, removing any air from the system.
- Aktive chofaj: Once flushed, turn on the power to the hot water tank. Allow approximately 15-20 minutes for the water to reach its set temperature.
Enstriksyon Operasyon
Your InSinkErator FHC3010 dispenser is designed for simple and intuitive operation.
Distribisyon dlo cho:
- Locate the hot water handle (typically on the left side).
- Push the handle back and hold it to dispense near-boiling water. Release the handle to stop the flow.
- Atansyon: Hot water can cause burns. Always use care when dispensing hot water.
Distribisyon dlo frèt:
- Locate the cold water handle (typically on the right side).
- Pull the handle forward and hold it to dispense filtered cold water. Release the handle to stop the flow.
Antretyen
Antretyen regilye asire lonjevite ak pèfòmans optimal dispansè ou a.
Netwayaj:
- Clean the exterior of the faucet with a soft, damp twal ak savon dou. Evite pwodui netwayaj abrazif oswa pwodui chimik ki agresif.
- For the Matte Black finish, use non-abrasive cleaning products specifically designed for matte surfaces to prevent damage.
Ranplasman filtè:
- The water filter (if installed) should be replaced every 6 months or as indicated by reduced water flow.
- Refer to your filter's specific instructions for replacement procedures.
Descaling (for Hot Water Tank):
- In areas with hard water, mineral deposits may accumulate in the hot water tank.
- Consult a qualified technician for descaling procedures if you notice a significant decrease in hot water flow or temperature.
Depanaj
If you encounter issues with your dispenser, refer to the following common problems and solutions:
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Pa gen dlo cho | Power not connected or tripped breaker. Tank not filled. | Check power connection and circuit breaker. Ensure water flows from the hot side before turning on power. |
| Koule dlo ki ba | Clogged filter. Kinked water line. | Replace water filter. Check water lines for kinks or obstructions. |
| Leaking from faucet | Loose connections. Damaged O-rings. | Tighten connections. Contact customer support for replacement parts or service. |
| Dlo pa cho ase | Temperature setting too low. Mineral buildup. | Adjust temperature setting on the tank (if applicable). Consider descaling. |
If the problem persists, please contact InSinkErator customer support.
Espesifikasyon
| Atribi | Detay |
|---|---|
| Mak | InSinkErator |
| Nimewo Modèl | 45394Y-ISE (FHC3010) |
| Koulè | Mat Nwa |
| Style | Modèn |
| Kalite enstalasyon | Anba koule |
| Kantite Anviwònman | 2 (Cho, Fwad) |
| Evalyasyon Tanperati Upper | 200 degre Fahrenheit |
| Sous pouvwa | Fil elektrik |
| Dimansyon pwodwi | 5.21 x 6 x 9 pous |
| Pwa atik | 4.3 liv |
Garanti ak sipò
InSinkErator products are built with quality and durability in mind. For specific warranty information, please refer to the warranty card included with your product or visit the official InSinkErator website. For technical support, replacement parts, or service inquiries, please contact InSinkErator customer service.
Ou ka jwenn plis enfòmasyon ak enfòmasyon pou kontakte yo sou Magazen InSinkErator sou Amazon.
