Entwodiksyon
The Pro-Ject Automat A1 is a fully automatic turntable system designed to deliver high-fidelity audio. It features an 8.3-inch ultra-light aluminum tonearm, a damped metal platter, and comes pre-fitted with an Ortofon OM10 cartridge. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your turntable to ensure optimal performance and longevity.
Imaj: Anwo-anba view of the Pro-Ject Automat A1 turntable with a record on the platter.
Enfòmasyon sou Sekirite
Please read all safety instructions before operating the turntable. Keep this manual for future reference.
- Pa ekspoze aparèy la a lapli oswa imidite.
- Pa mete objè ki ranpli ak likid, tankou vaz, sou aparèy la.
- Pa mete sous flanm dife, tankou bouji limen, sou aparèy la.
- Asire bon vantilasyon. Pa bloke okenn ouvèti vantilasyon.
- Use only the power supply provided by the manufacturer.
- Dekonekte ploge kouran an nan priz miray la si ou pa pral itilize aparèy la pou yon bon bout tan.
- Refere tout sèvis yo bay pèsonèl sèvis kalifye.
Ki sa ki nan bwat la
Lè w ap debale, tanpri asire w ke tout atik ki nan lis anba a yo la epi yo an bon kondisyon:
- Pro-Ject Automat A1 Turntable
- Pwovizyon pou pouvwa
- Kouvèti Pousyè
- 7-inch Single Adapter
- Connect-IT E Phono Cable (pre-fixed)
- Te santi Mat
- Multilingual Setup Guide (this manual)
Enstalasyon
1. Plasman
Place the turntable on a stable, level surface away from direct sunlight, heat sources, and excessive vibration. Ensure there is enough space around the unit for ventilation and operation.
Imaj: Bò kote view of the Pro-Ject Automat A1 turntable, illustrating its compact design on a flat surface.
2. Debalaj ak Asanble
- Retire platin an nan anbalaj li avèk prekosyon.
- Place the felt mat onto the platter.
- Install the dust cover by aligning its hinges with the slots at the rear of the turntable.
- The Ortofon OM10 cartridge is pre-mounted and adjusted. No further cartridge alignment is typically required.
Imaj: Gwo plan view of the Ortofon OM10 cartridge, highlighting its elliptical stylus profile.
3. Koneksyon
- Connect the pre-fixed Connect-IT E Phono Cable to your amplifier's phono input. Ensure the ground wire is also connected to the amptèminal tè lifter la pou minimize ronfleman.
- Si ou amplifier does not have a dedicated phono input, you can use the turntable's built-in switchable Moving Magnet (MM) phono stage. Locate the phono stage switch (usually on the rear or underside) and set it to "Line" or "On" to use the internal preamp, then connect to any standard auxiliary input on your amplifier. Si ou amplifier has a phono input, set the switch to "Phono" or "Off" and use the amplifier's phono stage.
- Connect the power supply to the turntable and then plug it into a wall outlet.
Imaj: Dèyè view of the Pro-Ject Automat A1, showing the RCA output connectors and power input.
Image: Close-up of the gold-plated RCA output connectors and ground wire.
Enstriksyon Operasyon
1. Jwe yon Dosye
- Place a record on the platter, ensuring it is centered. If playing a 7-inch single, use the provided adapter.
- Select the correct speed (33 or 45 RPM) using the speed selector switch.
- Peze a KÒMANSE button. The tonearm will automatically move to the lead-in groove of the record and lower gently.
Image: Close-up of the control panel, showing the speed selector switch (33/45 RPM), tonearm lift lever, and START/STOP buttons.
2. Sispann Lektur
Pou sispann lèktur, peze la SISPANN bouton. Bra a ap leve otomatikman, li retounen nan repo li, epi plato a ap sispann vire.
3. Manual Tonearm Operation (Optional)
While the A1 is fully automatic, you can manually cue the tonearm using the lift lever. Move the lift lever up to raise the tonearm, position it over the desired track, then move the lever down to gently lower the tonearm onto the record.
Antretyen
1. Netwaye Stylus la
The stylus (needle) should be cleaned regularly to ensure optimal sound quality and prevent damage to your records. Use a soft brush designed for stylus cleaning, brushing gently from back to front (from the pivot point towards the stylus tip).
Imaj: Gwo plan view of a turntable stylus, emphasizing the delicate nature of the component.
2. Netwaye platin an
Wipe the turntable chassis and dust cover with a soft, dry, lint-free cloth. For stubborn marks, a slightly damp cloth can be used, followed by a dry cloth. Avoid using abrasive cleaners or solvents.
3. Platter and Belt
Periodically check the drive belt for wear or stretching. If the belt appears loose or cracked, it may need replacement to maintain accurate playback speed. The damped metal platter can be cleaned with a soft, dry cloth.
Imaj: Anba view of the turntable's damped metal platter, showing its construction.
Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Pa gen son oswa son an trè ba | Incorrect phono stage setting; cables not connected properly; amppwoblèm antre lifyè. | Check the phono stage switch on the turntable. Ensure all audio cables are securely connected to the correct inputs on your amplifier. Verifye ampseleksyon antre lifyè. |
| Chanson bri | Ground wire not connected; interference; faulty cable. | Ensure the ground wire from the turntable is securely connected to your amplifier's ground terminal. Try moving the turntable away from other electronic devices. Check cable integrity. |
| Anrejistreman an ap jwe twò vit/dousman | Incorrect speed selection; worn drive belt. | Verify the speed selector switch is set to the correct RPM (33 or 45). Inspect the drive belt for wear and replace if necessary. |
| Tonearm does not move or drop automatically | Turntable not powered; mechanism obstruction. | Ensure the turntable is powered on. Check for any obstructions preventing the tonearm's movement. If issues persist, contact support. |
Espesifikasyon
| Karakteristik | Detay |
|---|---|
| Non modèl | Automat A1 |
| Dimansyon pwodwi | 14.37 x 16.93 x 5.12 pous |
| Pwa atik | 12.32 liv (5.6 kilogram) |
| Mak | Pro-Ject |
| Koneksyon Teknoloji | Oksilyè |
| Maksimòm vitès wotasyon | 45 RPM (supports 33/45 RPM) |
| Konpozan ki enkli | Turntable, power supply, dust cover, 7'' single adapter, Connect-IT E Phono Cable (pre-fixed), Felt Mat, Multilingual setup guide |
| Karakteristik espesyal | Adjustable Speed 33/45, Included Dust Cover, Included Power Cable, Included RCA Phono Interconnects |
| Materyèl | Aluminum (Tonearm), Wood (Chassis) |
| Koulè | Nwa |
| Manifakti | Sistèm Audio Pro-Ject |
| Dat Premye Disponib | 21 avril 2022 |
Garanti ak sipò
Pro-Ject Audio Systems products are manufactured to the highest standards and undergo strict quality control. This product is covered by a manufacturer's warranty. Please refer to the warranty card included in your packaging for specific terms and conditions.
For technical support, service, or warranty claims, please contact your authorized Pro-Ject dealer or visit the official Pro-Ject Audio Systems websit pou enfòmasyon kontak.
