Manyèl Enstriksyon pou Bwat Odinatè Antec NX200 M Micro-ATX Mini-Tower

1. Pwodwi souview

The Antec NX200 M is a compact Micro-ATX mini-tower computer case designed for efficient component housing and effective cooling. It features a mesh front panel for optimal airflow and a tempered glass side panel to showcase internal components. This manual provides essential information for setting up, operating, and maintaining your computer case.

Figure 1: Antec NX200 M Micro-ATX Mini-Tower Computer Case, showcasing its sleek black design and tempered glass side panel.

Karakteristik kle:

• Sipò pou plak mèr: Up to Micro-ATX form factor.
• Opsyon Depo: Supports one 2.5" SSD and two convertible 3.5" HDD / 2.5" SSD bays.
• Graphics Card Clearance: Accommodates graphics cards up to 275 mm in length.
• CPU Cooler Wotè: Supports CPU coolers up to 150 mm in height.
• Power Supply Unit (PSU) Support: Compatible with PSUs up to 150 mm in length.
• Vantilatè pre-enstale: Includes one 120mm rear fan for immediate cooling.
• Mesh Front Panel: Designed for enhanced airflow and heat dissipation.

2. Enstalasyon ak Enstalasyon

Follow these steps to install your components into the Antec NX200 M case.

2.1 Prepare Ka a

Before installation, ensure the case is placed on a stable, flat surface. Carefully remove the tempered glass side panel by unscrewing the four thumb screws located at each corner. Set the panel aside in a safe place to prevent damage.

Figi 2: Entèn view of the Antec NX200 M case, illustrating the spacious layout for component installation and cable routing.

2.2 Enstalasyon mèr

1. Install the necessary motherboard standoffs into the motherboard tray according to your Micro-ATX motherboard's screw holes.
2. Mete kat manman ou a ak anpil atansyon sou distans yo, aliyen twou vis yo.
3. Sere kat manman an byen sere ak vis yo bay yo.

2.3 Enstalasyon Power Supply Unit (PSU).

1. The PSU mounts at the bottom rear of the case. Slide your PSU into the designated compartment.
2. Fikse PSU a nan bwat la avèk vis ki nan dèyè a.
3. Route the necessary power cables through the cable management cutouts to the motherboard and other components.

2.4 Enstalasyon Disk Depo

The case supports various storage configurations:

• One dedicated 2.5" SSD bay.
• Two convertible 3.5" HDD / 2.5" SSD bays.

Install your SSDs and HDDs into the appropriate bays and secure them with screws.

2.5 Enstalasyon Kat Grafik

The NX200 M supports graphics cards up to 275 mm in length.

1. Retire kouvèti fant PCI-E ki nesesè yo nan dèyè bwat la.
2. Insert your graphics card into the appropriate PCI-E slot on your motherboard.
3. Fikse kat grafik la ak vis.

Figure 3: Diagram illustrating maximum component clearances for CPU cooler (150mm), GPU (275mm), and PSU (150mm) within the Antec NX200 M case.

2.6 Enstalasyon Sistèm Refwadisman

The case offers flexible cooling options:

• Devan: Supports 2 x 120mm or 2 x 140mm fans, or a 240mm radiator.
• Top: Sipòte 2 fanatik 120mm.
• Dèyè: Includes 1 x 120mm fan (pre-installed), also supports a 120mm radiator.

Install additional fans or radiators as desired, ensuring proper airflow direction.

Figure 4: Diagram detailing the fan and radiator mounting options for the Antec NX200 M case, including front, top, and rear placements.

2.7 Jesyon kab

Utilize the cable routing cutouts and tie-down points behind the motherboard tray to organize cables. This improves airflow and maintains a clean aesthetic.

3. Operasyon

3.1 Limen/Etenyen

Connect your power cable to the PSU and a wall outlet. Press the power button located on the top front panel of the case to turn your system on or off.

3.2 Using Front Panel Ports

Panèl devan an bay aksè fasil pou:

• 1 x USB 3.0 pò
• 2 x pò USB 2.0
• Jack kas ekoutè
• Jack mikwofòn
• Bouton Reyajiste

Ensure all internal front panel connectors are correctly attached to your motherboard for full functionality.

Figi 5: Anwo-anba view of the Antec NX200 M case, highlighting the accessible front I/O panel with USB ports, audio jacks, and power/reset buttons.

4. Antretyen

4.1 Netwayaj

Netwaye deyò bwat la regilyèman avèk yon twal mou, damp cloth. Avoid abrasive cleaners. For internal cleaning, power off and unplug your PC. Use compressed air to remove dust from fans, heatsinks, and internal components. Ensure proper ventilation during cleaning.

4.2 Filtè Pousyè

The Antec NX200 M features dust filters on the mesh front panel and potentially other intake areas. Periodically remove and clean these filters to maintain optimal airflow and prevent dust buildup inside the case.

NAN. Depanaj

5.1 Pa gen pouvwa

• Check if the power cable is securely connected to both the PSU and the wall outlet.
• Ensure the PSU's power switch is in the 'ON' position.
• Verify that the front panel power button connector is correctly attached to the motherboard.

5.2 Overheating Issues

• Ensure all case fans are spinning correctly and are oriented for optimal airflow (intake at front/bottom, exhaust at rear/top).
• Clean any dust buildup from fans and dust filters.
• Verify that CPU cooler and GPU fans are functioning properly.

5.3 Component Fit Issues

• Refer to the specifications section for maximum clearances for CPU coolers (150mm) and graphics cards (275mm).
• Ensure your components do not exceed these dimensions.

6. Espesifikasyon

7. Garanti ak sipò

For warranty information, technical support, or further assistance, please refer to the official Antec websit la oubyen kontakte sèvis kliyan yo dirèkteman. Kenbe prèv acha ou pou reklamasyon garanti.