Manyèl Enstriksyon pou Bwat PC ATX AeroCool Miragebk

Entwodiksyon

This manual provides comprehensive instructions for the installation, operation, and maintenance of your AeroCool Miragebk ATX PC Case. The Miragebk features an ARGB LED strip on the front panel, a hinged tempered glass side panel, and a 12 cm ARGB fan, designed for optimal component visibility and cooling performance.

Kontni pake

• AeroCool Miragebk ATX PC Case
• Accessory kit (screws, standoffs, cable ties)
• Manyèl Itilizatè (dokiman sa a)

Enfòmasyon sou Sekirite

Please read and understand all safety instructions before installing or operating this product. Failure to do so may result in injury or damage to the product.

• Always disconnect the power supply from the wall outlet before performing any installation or maintenance.
• Avoid placing the case in direct sunlight or near heat sources.
• Keep the case away from water and excessive humidity.
• Handle the tempered glass panel with care to prevent breakage.
• Asire bon baz pou anpeche danje elektrik.

Enstalasyon ak Enstalasyon

Follow these steps to set up your AeroCool Miragebk PC case and install components.

1. Prepare Ka a

1. Mete bwat la sou yon sifas ki plat e ki estab.
2. Carefully open the hinged tempered glass side panel. This panel provides full access to the interior.
3. Remove any protective films from the glass and other surfaces.

Figi 1: Devan view of the AeroCool Miragebk PC case, showcasing the ARGB LED strip and tempered glass panel.

2. Enstalasyon mèr

1. Install the I/O shield into the rear opening of the case.
2. Align your ATX, Micro ATX, or Mini ITX motherboard with the standoffs inside the case.
3. Secure the motherboard using the provided screws.

3. Enstalasyon ekipman pou pouvwa

1. Install the power supply unit (PSU) into the dedicated compartment at the bottom of the case.
2. Fikse PSU a ak vis nan dèyè bwat la.

4. Storage Drive Installation (HDDs/SSDs)

The case supports up to 7 HDDs and SSDs.

1. Locate the drive bays or mounting points.
2. Mount your 2.5" SSDs or 3.5" HDDs using the appropriate screws.

5. Enstalasyon Kat Grafik (GPU)

Bwat la sipòte kat grafik ki rive jiska 356mm longè.

1. Retire kouvèti fant ekspansyon ki nesesè yo nan dèyè bwat la.
2. Insert your graphics card into the PCIe slot on the motherboard.
3. Fikse kat grafik la ak vis.

6. Cooling System Installation (Fans/Liquid Cooling)

The case supports up to 8 fans and liquid cooling on the front, top, and rear.

• Install additional fans as needed for optimal airflow.
• For liquid cooling, mount radiators to the designated areas (front, top, or rear).
• The case includes one 12 cm ARGB fan.

Figi 2: Angle view of the AeroCool Miragebk PC case, highlighting the top mesh for ventilation and the front panel design.

7. Jesyon kab

Utilize the cable routing cutouts and tie-down points behind the motherboard tray to manage cables for improved airflow and aesthetics.

8. Closing the Case

Once all components are installed and cables are managed, close the tempered glass side panel and secure it.

Enstriksyon Operasyon

Front Panel I / O

The top panel of the AeroCool Miragebk provides convenient access to essential ports and controls:

• Bouton pouvwa: Limen/etenn òdinatè a.
• Bouton Reyajiste: Restarts the PC.
• Bouton kontwòl LED: Cycles through ARGB lighting modes or syncs with the motherboard.
• Pò USB 3.0 (x2): Pou transfè done gwo vitès.
• Pò USB 2.0 (x1): Pou aparèy USB estanda yo.
• HD Audio & Microphone Jacks: Pou antre ak sòti odyo.

Kontwòl ekleraj ARGB

The ARGB lighting on the front panel and included fan can be controlled in two ways:

• Bouton kontwòl LED: Press the dedicated LED button on the top panel to cycle through various pre-set ARGB lighting effects.
• Senkronizasyon plak mèr: Connect the ARGB lighting to a compatible 3-pin +5V ARGB header on your motherboard. This allows software control of 16.8 million colors and synchronization with other ARGB components. The Mirage control hub supports up to 6 ARGB fans and 2 additional 3-pin ARGB accessories.

Antretyen

Antretyen regilye ede asire pèfòmans optimal ak lonjevite bwat PC ou a.

• Filtè Pousyè: Periodically remove and clean the dust filters (if present) to maintain good airflow and prevent dust buildup inside the case.
• Netwayaj eksteryè: Siye sifas eksteryè yo ak yon mou, damp twal. Evite pwodui netwayaj abrazif oswa solvan.
• Netwayaj enteryè: Use compressed air to remove dust from internal components and fans. Ensure the PC is powered off and unplugged before cleaning.
• Tanpered Glass: Netwaye panèl an vè apeze a avèk yon twal mikwofib ak yon pwodui netwayaj vit ki fèt pou aparèy elektwonik.

Depanaj

If you encounter issues with your AeroCool Miragebk case, refer to the following common solutions:

• Odinatè a pa limen:
  • Ensure the power supply is properly connected to the wall outlet and switched on.
  • Verify all internal power cables (24-pin ATX, CPU, GPU) are securely connected.
  • Check that the front panel power switch cable is correctly connected to the motherboard.
• Ekleraj ARGB pa fonksyone:
  • Confirm the ARGB cables are correctly connected to the motherboard's 3-pin +5V ARGB header or the internal control hub.
  • If using motherboard sync, ensure the motherboard's ARGB software is installed and configured correctly.
  • Try pressing the LED control button on the top panel to see if pre-set modes function.
• Move sikilasyon lè/Twòp chalè:
  • Check if all installed fans are spinning correctly.
  • Clean any dust filters and internal components.
  • Ensure proper fan orientation (intake/exhaust) for optimal airflow.

Espesifikasyon

Garanti ak sipò

For warranty information or technical support, please refer to the official AeroCool websit la oubyen kontakte depatman sèvis kliyan yo. Kenbe prèv acha ou pou reklamasyon garanti.