1. Entwodiksyon
Thank you for choosing the AQQA Submersible Aquarium Water Pump. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your pump. Please read these instructions thoroughly before use and retain them for future reference.
This submersible pump is designed for various aquatic applications, including aquariums, fish tanks, ponds, and hydroponic systems. It features an adjustable flow rate, ultra-quiet operation, and a high lift capability.
2. Enstriksyon Sekirite Enpòtan
- Sekirite elektrik: Asire ekipman pou pouvwa a voltage matches the pump's specifications (110V). Always unplug the pump from the power outlet before performing any maintenance, installation, or when not in use. Do not operate the pump with a damaged cord or plug.
- Submersion: The pump must be completely immersed in water during operation to prevent dry burning, which can damage the motor and void the warranty.
- Tanperati: The pump is equipped with an automatic power-off feature if the water temperature exceeds 85°C (185°F) to prevent overheating.
- Plasman: Position the pump securely on a flat surface within the water body. Ensure it is not obstructed by debris.
- Timoun ak bèt kay: Kenbe ponp lan ak kòd elektrik li lwen timoun ak bèt kay.
- Itilizasyon entansyonèl: This pump is designed for water circulation in aquatic environments. Do not use it for flammable liquids, corrosive chemicals, or other non-water applications.
3. Pake kontni
Verifye ke tout atik ki nan lis anba a yo enkli nan pakè ou a:
- AQQA Submersible Water Pump (Model AQ009, 265GPH 15W)
- 1/2 inch (13mm) Nozzle
- 5/8 inch (16mm) Nozzle
- Manyèl itilizatè
Figure 3.1: AQQA Submersible Water Pump with included 13mm and 16mm nozzles.
Figure 3.2: Detailed diagram showing the water outlet, rotary adjustment button, protective water inlet cover, UL cable (6ft, 3-prong plug), handle, and shockproof rubber feet of the 15W pump.
4. Pwodwi Features
- Pousantaj koule reglabl: A rotary knob allows precise control over water flow.
- Operasyon ultra-trankil: Equipped with a pure copper motor and ceramic shaft impeller for minimal noise.
- Segondè kapasite leve: Capable of pumping water to a maximum height of 4.9 feet.
- Low Water Level Pumping: Designed to pump water down to 1 inch (approximately 1cm) from the bottom.
- 360° Bottom Suction: Efficiently removes dirt and impurities from the bottom of the tank.
- Karakteristik sekirite: IPX8 waterproof rating and automatic power-off protection against dry burning (if water temperature exceeds 85°C).
- Konstriksyon dirab: Made from Acrylonitrile Butadiene Styrene (ABS) with a durable pure copper motor.
- Manch entegre: A 90° rotating handle for convenient placement and removal.
Figi 4.1: Avantaj kletages of the pump, including a silent ceramic shaft, rubber damping anti-slip feet, high-quality motor with anti-dry burning protection (auto power off above 85°C), and a hidden handle for convenience.
Figure 4.2: Illustrates the pump's IPX8 waterproof rating and its durable pure copper motor, highlighting its robust construction.
Figure 4.3: Demonstrates the pump's ability to operate effectively at a low water level, down to approximately 1 cm (0.4 inches) from the bottom.
5. Enstriksyon Enstalasyon
- Chwazi bouch: Choose the appropriate nozzle (13mm or 16mm) for your application. The 13mm nozzle provides a narrower, stronger flow, while the 16mm nozzle offers a wider flow.
- Tache bouch: Securely screw the selected nozzle onto the pump's water outlet.
- Plasman: Place the pump completely submerged in the water body (aquarium, pond, etc.). Ensure the pump is stable and not resting on loose debris.
- Koneksyon pouvwa: Once the pump is fully submerged, plug the 6ft power cord into a standard 110V electrical outlet.
Figure 5.1: The AQQA pump installed in an aquarium, illustrating the connection of different nozzle sizes for varied water flow requirements.
6. Operasyon Enstriksyon
- Pouvwa sou: After proper setup and submersion, plug in the pump to start operation.
- Ajiste To Debi a: Locate the 'FLOW VALVE' rotary knob on the side of the pump. Rotate the knob towards '+' to increase the water flow rate, or towards '-' to decrease it. Note that the flow cannot be completely turned off using this knob.
- Siveyans: Observe the water flow and adjust as needed for your specific application.
- Pouvwa Off: To stop the pump, unplug it from the electrical outlet. Always unplug before removing the pump from water.
Figi 6.1: Close-up view of the rotary switch (Flow Valve) on the pump, used to adjust the water flow rate from minimum to maximum.
7. Antretyen
Regular cleaning and maintenance will ensure the longevity and optimal performance of your AQQA water pump.
- Dekonekte pouvwa: Toujou debranche ponp lan nan sous kouran an anvan nenpòt antretyen.
- Remove from Water: Carefully remove the pump from the water body.
- Demonte: Gently twist and pull the base of the pump to detach it. This will expose the impeller assembly.
- Netwaye Enpèlè: Remove the impeller and clean it thoroughly with a soft brush and clean water to remove any accumulated debris, algae, or mineral deposits. Ensure the impeller shaft is also clean.
- Clean Inlet Cover: Clean the protective water inlet cover to ensure unrestricted water flow.
- Remonte: Reassemble the pump by carefully placing the impeller back and securing the base. Ensure all parts are fitted correctly.
- Frekans: Clean the pump regularly, especially if you notice a decrease in flow rate or increased noise.
Figure 7.1: Instructions for easy cleaning: regularly disassemble the base and clean the impeller to prevent blockages and maintain optimal performance.
Figure 7.2: The ceramic impeller, designed for durability and quiet operation in both fresh and saltwater environments.
NAN. Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Ponp pa kòmanse | Pa gen ekipman pou pouvwa Impeller bloke Pwoteksyon boule sèk aktive | Tcheke koneksyon kouran ak priz Unplug, disassemble, and clean impeller Ensure pump is fully submerged and water temperature is below 85°C |
| Koule dlo redwi | Clogged inlet or impeller Flow rate knob set too low Lè nan ponp lan | Unplug, disassemble, and clean pump components Adjust flow rate knob towards '+' Ensure pump is fully submerged and free of air pockets |
| Twòp bri oswa Vibration | Enpèlè bloke oswa domaje Pump not stable Kouri sèk | Unplug, inspect, and clean impeller. Replace if damaged. Ensure pump is placed on a flat, stable surface Ensure pump is fully submerged in water |
| Ponp sispann san atann | Overheating (dry burning protection) Entèripsyon pouvwa | Check water level and temperature. Allow pump to cool before restarting. Tcheke ekipman pou pouvwa |
9. Espesifikasyon
| Karakteristik | Detay |
|---|---|
| Modèl | AQ009 |
| Pouvwa | 15W |
| Voltage | 110V |
| Pousantaj maksimòm koule | 265 GPH (1000 L/H) |
| Maksimòm Leve Wotè | 4.9 pye |
| Dimansyon pwodwi (L x W x H) | 4" x 4" x 4" |
| Pwa atik | 0.56 kg (1.23 liv) |
| Materyèl | Akrilonitrile butadien stirèn (ABS) |
| Outlet Connection (Nozzles) | 1/2" (13mm), 5/8" (16mm) |
| Longè kòd pouvwa | 6 pye |
| Evalyasyon ki enpèmeyab | IPX8 |
Figure 9.1: Comprehensive table detailing product parameters including power, flow rate, head max, power cord length, outlet connections, and voltage for various pump models. This manual focuses on the 15W model.
10. Garanti ak sipò
For warranty information or technical support, please refer to the product packaging or contact AQQA customer service directly. Keep your purchase receipt as proof of purchase.
Pou plis asistans, ou ka vizite AQQA Store on Amazon.
