Entwodiksyon
This manual provides essential instructions for the safe and efficient operation, maintenance, and troubleshooting of your Truper ENNE-160 16 Gauge Pneumatic Stapler. Please read this manual thoroughly before using the tool to ensure proper handling and to prevent injury or damage.
Figure 1: Truper ENNE-160 16 Gauge Pneumatic Stapler, side view.
Enfòmasyon sou Sekirite
Toujou swiv prekosyon sekirite debaz yo lè w ap itilize zouti elektrik pou diminye risk dife, chòk elektrik, ak aksidan pèsonèl. Kenbe manyèl sa a pou referans pita.
- Mete pwoteksyon pou je: Toujou mete linèt sekirite oswa pwoteksyon pou pwoteje tèt ou kont debri k ap vole.
- Mete pwoteksyon pou tande: Prolonged exposure to noise from pneumatic tools can cause hearing damage.
- Dekonekte ekipman pou lè a: Always disconnect the air supply before making adjustments, clearing jams, or performing maintenance.
- Kenbe Zòn Travay la Apwòp: Asire w ke zòn travay ou a byen limen epi li pa gen dezòd.
- An sekirite pou pyès travay la: Always secure the material you are working on to prevent movement.
- Pa janm montre moun ak dwèt ou: Never point the tool at yourself or others, even if it is not connected to an air supply.
- Sèvi ak presyon lè ki kòrèk la: Operate the tool within the specified air pressure range (75-110 PSI).
- Enspekte zouti a anvan ou itilize li: Check for damaged parts, loose fasteners, or any other condition that may affect safe operation.
Karakteristik pwodwi
The Truper ENNE-160 Pneumatic Stapler is designed for efficiency and user comfort. Key features include:
- Lojman aliminyòm: Durable and lightweight construction for extended use.
- Manch ergonomic: Designed for operator comfort and reduced fatigue.
- Sistèm degaje rapid: Facilitates easy clearing of jammed staples.
- Adjustable Depth Control: Allows precise control over staple depth.
- Metallic Contact Safety: Ensures staples are only fired when the tool is pressed against the workpiece.
- 360° Rotatable Air Exhaust Valve: Directs exhaust air away from the operator for improved comfort.
- Staple konpatibilite: Uses staples from 3/4" to 2" in length.
- Presyon travay: Operates efficiently between 75 and 110 PSI.
- Kapasite katouch: Holds up to 100 staples.
Figure 2: Key features and components of the Truper ENNE-160 Pneumatic Stapler.
Espesifikasyon
| Atribi | Valè |
|---|---|
| Nimewo Modèl | ENNE-160 |
| Staple Gauge | 16 Calibri |
| Materyèl | Aliminyòm |
| Travay presyon | 75 - 110 PSI (517 - 758 kPa) |
| Staple Lengths | 3/4", 1", 1 1/4", 1 1/2", 1 3/4", 2" |
| Kapasite katouch | 100 Staples |
| Konsomasyon lè | 8.9 CFM @ 90 PSI (252 L/min @ 620 kPa) |
| Dimansyon pwodwi | 11 x 36 x 31 cm (apeprè 4.3 x 14.2 x 12.2 pous) |
| Pwa pwodwi | 3.6 kg (apeprè 7.9 liv) |
Figure 3: Dimensions of the Truper ENNE-160 Pneumatic Stapler.
Enstalasyon
- Konekte ekipman pou lè a:
- Ensure the air compressor is off and depressurized.
- Connect a 1/4" NPT quick-change connector to the air inlet of the stapler.
- Attach the air hose from your compressor to the stapler's connector.
- Set the air compressor pressure regulator to the recommended operating range of 75-110 PSI. Do not exceed 110 PSI.
- Chaje Staples:
- Disconnect the air supply before loading staples.
- Locate the staple magazine release latch, typically at the rear of the magazine.
- Pull the magazine open or slide it back.
- Insert a strip of 16 gauge staples (3/4" to 2" length) into the magazine with the points facing down.
- Close the magazine securely until it latches.
- Adjust Depth Control:
- The stapler features an adjustable depth control mechanism.
- Rotate the depth adjustment knob or lever (refer to Figure 2 for location) to set the desired staple depth. Test on a scrap piece of material first.
Enstriksyon Operasyon
- Prepare pyès travay la: Ensure the material is clean, dry, and free of obstructions. Secure the workpiece if necessary.
- Connect Air: Reconnect the air supply to the stapler.
- Zouti Pozisyon: Place the nose of the stapler firmly against the workpiece where you want to drive a staple. The metallic contact safety mechanism requires pressure against the surface to allow firing.
- Fire Staple: Squeeze the trigger to drive a staple. Release the trigger after each staple.
- Continuous Operation (if applicable): Some models allow for bump firing. If your model supports this, hold the trigger and bump the nose of the tool against the workpiece to drive staples rapidly. Always exercise caution with this mode.
- Efase blokaj: If a staple jam occurs, immediately disconnect the air supply. Use the quick-release system to open the magazine and carefully remove the jammed staple. Reconnect air only after the jam is cleared and the magazine is closed.
- Adjust Air Exhaust: The 360° rotatable air exhaust valve can be adjusted to direct exhaust air away from your face or the workpiece.
Antretyen
Regular maintenance ensures the longevity and optimal performance of your pneumatic stapler. Always disconnect the air supply before performing any maintenance.
- Lubrifikasyon: Apply a few drops of pneumatic tool oil into the air inlet daily or before each use. This lubricates internal components. Do not use detergent oil or automotive oil.
- Netwayaj: Keep the tool clean and free of debris. Wipe down the exterior with a clean cloth. Periodically clean the magazine and nose area to prevent staple jams.
- Filtè lè: Si konpresè lè ou a gen yon filtè lè anndan zouti a, asire w ou netwaye oswa ranplase li regilyèman pou anpeche kontaminan antre nan zouti a.
- Enspekte tiyo ak ekipman yo: Regularly check air hoses and fittings for wear, leaks, or damage. Replace any damaged components immediately.
- Depo: Store the stapler in a dry, clean environment when not in use. Disconnect it from the air supply.
Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Zouti pa tire | No air supply; Low air pressure; Safety contact not engaged; Jammed staples; Trigger mechanism fault. | Check air connection and compressor pressure; Ensure tool nose is firmly pressed against workpiece; Disconnect air and clear jam; Contact service if trigger fault. |
| Staples not driven fully | Low air pressure; Depth control set too shallow; Incorrect staple length for material. | Increase air pressure (within limits); Adjust depth control deeper; Use appropriate staple length. |
| Agraf yo bloke souvan | Damaged staples; Incorrect staple size; Dirty magazine; Worn driver blade. | Use new, correct staples; Clean magazine; Inspect and replace driver blade if worn. |
| Air leaks from tool | Ekipman ki lach; Bag O-ring oswa sele ki ize. | Tighten fittings; Lubricate tool; If leaks persist, contact service for seal replacement. |
Garanti ak sipò
TRUPER products are manufactured to high-quality standards. For warranty information, service, or technical support, please refer to the warranty card included with your product or visit the official TRUPER websit la. Kenbe resi acha ou kòm prèv acha pou reklamasyon garanti.
Manifakti: Truper SA de CV
