Trane VAL12000 OEM Thermostatic Expansion Valve

1. Pwodwi souview

The Trane VAL12000 / VAL-12000 is an Original Equipment Manufacturer (OEM) thermostatic expansion valve designed for use in various Trane chiller systems. This component plays a crucial role in the refrigeration cycle by controlling the amount of refrigerant flowing into the evaporator, ensuring efficient heat exchange and system performance.

It is a direct replacement for or supersedes models VAL-12000, VAL012000, VAL08573, VAL-8573, and VAL8573.

Figure 1: Illustrative stamp indicating Trane OEM Component. Actual product appearance may vary.

Commonly Used In:

• Various Trane Chillers: Rotary Chillers, RTAC Chillers, BCVC Chillers
• Specific Rotary Chiller Models: RTAC120, RTAC135, RTAC140, and others.

2. Espesifikasyon

Note: Specifications are subject to change without notice. Always refer to the product label for the most accurate information.

3. Gid enstalasyon yo

Installation of the Trane VAL12000 expansion valve should only be performed by qualified HVAC technicians. Improper installation can lead to system malfunction, refrigerant leaks, and potential safety hazards. Always follow industry best practices and local codes.

3.1 Prekosyon sekirite

• Ensure the system is de-energized and depressurized before beginning any work.
• Mete Ekipman Pwoteksyon Pèsonèl (EPI) ki apwopriye, tankou linèt sekirite ak gan.
• Handle refrigerants with care, following all safety guidelines.
• Asire bon vantilasyon nan zòn travay la.

3.2 Etap Enstalasyon (Jeneral)

1. Preparasyon sistèm: Isolate the section of the refrigeration system where the valve is to be installed. Recover any refrigerant according to environmental regulations.
2. Retire ansyen valv la: Carefully disconnect and remove the existing expansion valve, noting its orientation and connections.
3. Prepare Nouvo Valv la: Inspect the new VAL12000 valve for any damage. Ensure all connection points are clean and free of debris.
4. Konekte Valv la: Install the new valve, ensuring proper alignment and secure connections. Use appropriate brazing or flaring techniques as required by the system design. Pay close attention to the M12 input and ODS connections.
5. Thermal Bulb Placement: Securely attach the thermal bulb to the suction line in the correct location, typically just after the evaporator outlet, ensuring good thermal contact. Insulate the bulb to prevent ambient temperature interference.
6. Leak Tcheke: After installation, perform a thorough leak check using an appropriate leak detection method.
7. Evakyasyon ak Chaje: Evacuate the system to a deep vacuum to remove non-condensables and moisture. Recharge the system with the correct type and amount of refrigerant as specified by the chiller manufacturer.
8. Sistèm demaraj: Slowly bring the system back online and monitor its performance to ensure proper operation of the expansion valve.

For detailed, system-specific installation instructions, refer to the service manual of the Trane chiller unit in which this valve is being installed.

4. Operasyon

The Trane VAL12000 is a thermostatic expansion valve (TXV) that automatically regulates the flow of liquid refrigerant into the evaporator based on the superheat of the refrigerant vapor leaving the evaporator. Its primary function is to maintain a constant superheat, ensuring the evaporator is fully utilized without allowing liquid refrigerant to return to the compressor.

The thermal bulb, sensing the temperature of the suction line, transmits pressure to the diaphragm within the valve. This pressure, balanced against the evaporator pressure and spring pressure, modulates the valve's opening. This dynamic control optimizes system efficiency and protects the compressor from liquid slugging.

5. Antretyen

The Trane VAL12000 expansion valve is a robust component designed for long-term reliability. While it generally requires minimal direct maintenance, its optimal performance is dependent on the overall health and cleanliness of the refrigeration system.

5.1 Recommended Practices

• Netwaye sistèm: Ensure the refrigeration system remains free of contaminants (moisture, acids, debris) which can cause corrosion or blockages within the valve. Regular filter dryer replacement is crucial.
• Refrigerant Quality: Use only the specified type and quality of refrigerant.
• Siveyans pèfòmans: Periodically monitor system superheat and subcooling. Deviations can indicate issues with the expansion valve or other system components.
• Deteksyon koule: Regularly check for refrigerant leaks around valve connections.

Any adjustments or repairs to the expansion valve or refrigeration system should be performed by certified HVAC professionals.

NAN. Depanaj

Troubleshooting issues related to an expansion valve often involves diagnosing overall system performance. The following are common symptoms that might indicate an issue with the expansion valve, though they can also be caused by other system components.

Enpòtan: Troubleshooting refrigeration systems requires specialized knowledge and tools. Always consult with or hire a qualified HVAC technician for diagnosis and repair.

7. Garanti ak sipò

As an OEM component, the Trane VAL12000 expansion valve is typically covered under the warranty terms provided by Trane for their chiller systems or by the distributor from whom it was purchased. Specific warranty details, including duration and coverage, may vary.

For warranty claims, technical support, or to order replacement parts (such as MOD02686 for a stepper motor or MOD02688 for a cable, if applicable to your system), please contact your authorized Trane distributor or a certified HVAC service provider.

Manifakti: Trane

Kontakte: Refer to your local Trane representative or the official Trane website for service and support information.