1. Pwodwi souview
The Ozito Air Spray Gun (Model: 4472350) is a versatile tool designed for efficient application of various coatings. Its suction-feed design and adjustable controls make it suitable for a wide range of painting tasks, from general-purpose spraying to applying specific finishes and sealants. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.
Figure 1: Ozito Air Spray Gun with attached 1000 ml paint pot.
2. Enfòmasyon sou Sekirite
Always observe basic safety precautions to reduce the risk of fire, electric shock, and personal injury when using this product.
- Li Manyèl la: Thoroughly read and understand all instructions before operating the spray gun.
- Ekipman Pwoteksyon Pèsonèl (PPE): Always wear appropriate eye protection (safety glasses/goggles), respiratory protection (respirator mask), and protective gloves.
- Vantilasyon: Use the spray gun in a well-ventilated area to avoid inhalation of fumes and to prevent the buildup of flammable vapors.
- Materyèl ki ka pran dife: Do not spray flammable or combustible materials near open flames, pilot lights, or other ignition sources.
- Sekirite elektrik: Ensure your air compressor and any extension cords are properly grounded and rated for the power requirements.
- Kenbe timoun yo lwen: Do not allow children or untrained persons to operate the spray gun.
- Koneksyon an sekirite: Ensure all air hose connections are secure before operation.
3. Konpozan ak pyès
The Ozito Air Spray Gun comes with the following main components:
- Suction Spray Gun Body
- 1.5 mm Nozzle (pre-installed or included)
- 1000 ml Paint Pot (Suction Cup)
- Fluid Adjustment Dial
- Fan Adjustment Dials
- Air Inlet Connector
Figi 2: Side view of the Ozito Air Spray Gun, showing the handle and air inlet.
4. Enstalasyon
- Dekonpoze: Retire tout konpozan yo nan anbalaj la avèk prekosyon. Enspekte pou wè si gen nenpòt domaj.
- Connect Air Compressor: Attach a suitable air hose (not included) from your air compressor to the air inlet connector on the spray gun. Ensure the compressor can provide a minimum flow rate of 85 liters per minute.
- Prepare materyèl: Prepare your paint, topcoat, or sealant according to the manufacturer's instructions. Ensure it is properly thinned for spraying consistency.
- Fill Paint Pot: Unscrew the paint pot from the spray gun body. Fill the pot with your prepared material, ensuring not to overfill. Reattach the paint pot securely to the spray gun.
- Ajisteman Inisyal yo: Before spraying, make initial adjustments to the fluid and fan pattern dials. Start with a moderate setting.
5. Operasyon Enstriksyon
- Power On Compressor: Turn on your air compressor and allow it to build up sufficient pressure.
- Tès modèl espre: Before spraying your actual workpiece, test the spray pattern on a piece of scrap material. Adjust the fluid adjustment dial to control the amount of material sprayed and the fan adjustment dials to change the spray pattern (e.g., from a round to a flat pattern).
- Teknik flite: Hold the spray gun perpendicular to the surface, maintaining a consistent distance (typically 6-10 inches). Use smooth, even strokes, overlapping each pass by about 50%. Release the trigger at the end of each stroke.
- Ranpli: If the paint pot runs low, turn off the air supply, unscrew the pot, refill, and reattach before resuming.
6. Antretyen
Proper cleaning and maintenance are crucial for the longevity and performance of your spray gun.
- Netwayaj Imedya: Clean the spray gun immediately after each use. Do not allow material to dry inside the gun.
- Demonte: Disassemble the paint pot, nozzle, and air cap.
- Konpozan netwayaj: Clean all components thoroughly with an appropriate cleaning solution (e.g., paint thinner for oil-based paints, water for water-based paints). Use a cleaning brush to remove any residue from the nozzle and internal passages.
- Reyasanblaj: Reassemble the spray gun once all parts are clean and dry.
- Depo: Store the spray gun in a clean, dry place, away from extreme temperatures and direct sunlight.
NAN. Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Pa gen espre oswa espre fèb | Clogged nozzle or air cap; insufficient air pressure; material too thick. | Clean nozzle and air cap; check compressor pressure; thin material. |
| Modèl espre inegal | Dirty air cap; damaged nozzle; incorrect fan adjustment. | Clean air cap; replace nozzle if damaged; adjust fan dials. |
| Material spitting | Material too thick; air leak; low material in pot. | Thin material; check connections for leaks; refill paint pot. |
8. Espesifikasyon
- Non modèl: ASG-SFEU; EX; UK
- Nimewo Modèl Atik: 4472350
- Mak: Ozito
- Gwosè bouch: 1.5 mm
- Paint Pot Capacity: 1000 ml
- Minimum Air Compressor Flow Rate: 85 lit pou chak minit
- Koulè: Gri
- Eleman ki enkli: 1 suction spray gun
- Dimansyon pake: 28.5 x 19 x 11 cm
- Pwa atik: 790 gram
- Manifakti: Einhell
9. Garanti ak sipò
For information regarding warranty coverage, spare parts availability, or technical support, please refer to the official Ozito website or contact Ozito customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.
Resous sou entènèt: Vizite www.ozito.com.au (or your regional Ozito website) for product registration, FAQs, and support contact details.
