CAME 001ATPD4 4-Channel Dual Frequency Remote Control User Manual

1. Pwodwi souview

The CAME 001ATPD4 is a compact 4-channel remote control designed for operating CAME BROWN LINE automation systems, such as gate motors. This transmitter supports dual frequency operation without requiring modifications to the automation's frequency card, centralizing the management of your CAME equipment. It incorporates rolling code technology for enhanced security and features an LED indicator to signal low battery status.

Image showing the compact black CAME 4-channel remote control with four distinct buttons.

2. Karakteristik kle

• 4 chanèl: Allows control of up to four different automation functions or devices.
• Operasyon Doub Frekans: Compatible with CAME BROWN LINE automations operating on two different frequencies without requiring system adjustments.
• Rolling Code Technology: Enhances security by changing the transmission code each time the remote is used, preventing unauthorized duplication.
• Konsepsyon kontra enfòmèl ant: Ergonomic and easy to carry.
• Endikatè batri ki ba: An integrated LED warns when the battery level is low, indicating it's time for replacement.

3. Enstalasyon

3.1 Enstalasyon batri

The CAME 001ATPD4 remote control does not include batteries. To install or replace batteries:

1. Louvri kontwòl remote la avèk prekosyon casing. Refer to the diagram on the back of the remote for guidance on opening.
2. Insert the required battery type (refer to specifications) ensuring correct polarity (+/-).
3. Fèmen kontwòl remote la casing byen fèm.

3.2 Pairing with CAME Automation System

To enable the remote control to operate your CAME automation system, it must be paired with the receiver unit. The exact pairing procedure may vary slightly depending on your specific CAME automation model. Generally, the process involves:

1. Locate the receiver unit for your CAME gate motor or automation system. This is typically found within the control panel enclosure.
2. Access the programming button (often labeled 'PROG', 'MEM', or similar) on the receiver unit. You may need to consult your automation system's manual for its precise location and function.
3. Press and release the programming button on the receiver. An LED indicator on the receiver will usually light up or flash, indicating it is in programming mode.
4. Within a few seconds, press and hold the desired button on your new CAME 001ATPD4 remote control that you wish to assign to the automation function (e.g., gate open/close).
5. Keep the remote button pressed until the receiver's LED indicator changes (e.g., turns off, flashes rapidly, or lights solid), confirming successful pairing.
6. Lage bouton aleka a.
7. Test the remote control to ensure it operates the automation correctly.

If you encounter difficulties, refer to the specific instruction manual for your CAME automation system or contact CAME technical support.

4. Operasyon Enstriksyon

Once paired, operating the CAME 001ATPD4 remote control is straightforward:

• To Activate an Automation: Press the button on the remote control that has been programmed for the desired function (e.g., opening a gate, closing a barrier).
• Ranje: Ensure you are within the operational range of your CAME automation receiver. Obstacles and environmental factors can affect the range.
• Endikatè ki ap dirije: The remote control features an LED that illuminates when a button is pressed. If the LED is dim or does not light up, the battery may be low and require replacement.

5. Antretyen

5.1 Ranplasman batri

When the LED indicator on the remote control becomes dim or fails to light up during operation, it is time to replace the battery. Refer to section 3.1 for battery installation instructions.

5.2 Netwayaj

To clean the remote control, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the device.

5.3 Depo

Store the remote control in a dry place, away from direct sunlight, extreme temperatures, and corrosive substances. Avoid dropping the remote or subjecting it to strong impacts.

NAN. Depanaj

• Remote pa travay:
  • Check the battery. Replace if the LED is dim or off.
  • Ensure the remote is properly paired with the receiver (refer to Section 3.2).
  • Verify that the automation system itself is powered on and functioning correctly.
• Kout distans operasyon:
  • Replace the battery, even if the LED still lights up. A weak battery can reduce range.
  • Ensure there are no new obstructions between the remote and the receiver.
  • Check the antenna on the receiver unit for damage or obstruction.
• Endikatè ki ap dirije pa limen:
  • The battery is likely depleted. Replace it immediately.
  • Asire w ke pil la mete ak polarite ki kòrèk la.

If problems persist after attempting these troubleshooting steps, contact CAME technical support or a qualified technician.

7. Espesifikasyon

8. Garanti ak sipò

Specific warranty information for the CAME 001ATPD4 remote control is typically provided at the point of purchase or within the product packaging. Please retain your proof of purchase for warranty claims.

For technical support, further assistance with setup, or warranty inquiries, please contact your authorized CAME dealer or visit the official CAME websit pou jwenn enfòmasyon kontak nan rejyon ou an.