1. Entwodiksyon
The STLINK-V3SET is a modular, stand-alone debugging and programming probe designed for use with STM8 and STM32 microcontrollers. This device consists of a main module and a complementary adapter board, providing comprehensive functionality for development and testing.
It facilitates communication with target microcontrollers via SWIM and JTAG/SWD interfaces. Additionally, the STLINK-V3SET offers a Virtual COM port for host PC communication through UART, and bridge interfaces (SPI, I2C, CAN, GPIOs) for programming via bootloader. Its modular design allows for feature expansion through additional modules, such as the adapter board.
2. Karakteristik kle
- Konsepsyon modilè: Stand-alone probe with support for modular extensions.
- Pwovizyon pou pouvwa: Self-powered via a USB connector (Micro-B).
- Entèfas USB: USB 2.0 high-speed compatible.
- Mizajou mikrolojisyèl: Direct firmware update (DFU) support.
- JTAG / SWD Debugging:
- Application voltage support: 3 V to 3.6 V.
- 5 V tolerant inputs.
- Flat cables: STDC14 to MIPI10 / STDC14 / MIPI20 (1.27 mm pitch connectors).
- JTAG communication support.
- SWD and Serial Wire Viewer (SWV) communication support.
- SWIM Features (with adapter board MB1440):
- Application voltage support: 1.65 V to 5.5 V.
- SWIM header (2.54 mm pitch).
- SWIM low-speed and high-speed modes support.
- Virtual COM Port (VCP):
- Application voltage support on UART: 3 V to 3.6 V.
- 5 V tolerant inputs.
- VCP frequency up to 15 MHz.
- Available on STDC14 debug connector (not on MIPI10).
- Multi-path Bridge (USB to SPI/UART/I2C/CAN/GPIOs):
- Application voltage support: 3 V to 3.6 V.
- 5 V tolerant inputs.
- Signals available on adapter board only (MB1440).
- Flash Programming: Drag-and-drop functionality.
- Endikatè ki ap dirije: Two color LEDs for communication and power status.
3. Enstriksyon Enstalasyon
3.1. Debale ak Idantifikasyon Konpozan
Lè w ap ouvri pake a, verifye si tout konpozan yo la:
- STLINK-V3SET Main Module
- Adapter Board (MB1440)
- USB Cable (Micro-B)
- Flat cables (STDC14 to MIPI10 / STDC14 / MIPI20)
Figi 1: STLINK-V3SET Main Module (left) and Adapter Board (right). The main module is a white and blue rectangular device, while the adapter board is a blue circuit board with various connectors and components.
3.2. Enstalasyon chofè
Before connecting the STLINK-V3SET to your computer, ensure that the necessary drivers are installed. These drivers are typically available on the official STMicroelectronics website. Download and install the latest ST-LINK drivers for your operating system.
3.3. Konekte Aparèy la
- Connect the STLINK-V3SET Main Module to your computer using the provided USB Micro-B cable. The device is self-powered via USB.
- If using the adapter board (MB1440) for SWIM or bridge interfaces, connect it to the main module as required.
- Connect the appropriate debug cable (e.g., STDC14, MIPI10, MIPI20) from the STLINK-V3SET to your target STM8 or STM32 application board. Ensure correct pin orientation.
- Verify that the power and communication LEDs on the STLINK-V3SET illuminate, indicating proper connection and power.
4. Operasyon Enstriksyon
4.1. Debugging STM32 Microcontrollers (JTAG/SWD)
- Ensure your development environment (e.g., STM32CubeIDE, Keil MDK, IAR Embedded Workbench) is configured to use ST-LINK/V3 as the debugger.
- Connect the STLINK-V3SET to your STM32 target board using a JTAG or SWD cable.
- In your IDE, initiate a debug session. The STLINK-V3SET will establish communication with the target microcontroller.
- You can now step through code, set breakpoints, inspect variables, and perform other debugging operations.
4.2. Programming STM8 Microcontrollers (SWIM)
For STM8 programming, the adapter board (MB1440) is required.
- Connect the adapter board (MB1440) to the STLINK-V3SET Main Module.
- Connect the SWIM header from the adapter board to your STM8 target board.
- Use the appropriate programming software (e.g., STVP) to load your firmware onto the STM8 microcontroller.
4.3. Virtual COM Port (VCP) Usage
The VCP feature allows your host PC to communicate with the target microcontroller via UART.
- Ensure the STLINK-V3SET is connected to the target via the STDC14 debug connector.
- On your PC, identify the assigned COM port for the STLINK-V3SET VCP.
- Use a terminal emulator program (e.g., PuTTY, Tera Term) to open a connection to this COM port with the correct baud rate and settings.
- Data sent from your PC will be relayed to the target microcontroller's UART, and vice-versa.
4.4. Multi-path Bridge Interfaces (SPI, I2C, CAN, GPIOs)
These interfaces are available on the adapter board (MB1440) and allow for direct communication with peripherals on your target board.
- Connect the adapter board (MB1440) to the STLINK-V3SET Main Module.
- Wire the specific SPI, I2C, CAN, or GPIO pins from the adapter board to your target device.
- Utilize the ST-LINK utility software or custom applications to interact with these bridge interfaces.
4.5. Drag-and-Drop Flash Programming
The STLINK-V3SET supports convenient drag-and-drop programming for compatible microcontrollers.
- Connect the STLINK-V3SET to your target board.
- The target microcontroller may appear as a removable drive on your computer.
- Drag and drop your compiled firmware file (e.g., .hex, .bin) onto this drive to program the microcontroller.
5. Antretyen
5.1. Netwayaj
Keep the STLINK-V3SET and its adapter board clean and free from dust. Use a soft, dry cloth for cleaning. Avoid using liquid cleaners or solvents, as these can damage the electronic components.
5.2. Mizajou Firmware
Regularly check the STMicroelectronics website for firmware updates for your STLINK-V3SET. Firmware updates can provide new features, performance improvements, and bug fixes. Use the official ST-LINK utility software to perform firmware updates.
Procedure for Firmware Update:
- Download the latest ST-LINK utility from the STMicroelectronics websit.
- Connect the STLINK-V3SET to your computer via USB.
- Launch the ST-LINK utility.
- Navigate to the firmware update section within the utility and follow the on-screen instructions to update the device firmware.
NAN. Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Aparèy pa rekonèt pa PC |
|
|
| Cannot connect to target microcontroller |
|
|
| Mizajou mikrolojisyèl la echwe |
|
|
7. Espesifikasyon
| Karakteristik | Detay |
|---|---|
| Non modèl | STLINK-V3SET |
| Mak | STMicroelectronics |
| Koneksyon Teknoloji | I2C, USB |
| Konpozan ki enkli | Main module, Adapter board (MB1440) |
| Dimansyon pwodwi | 4 x 3 x 1 pous |
| Pwa | 4 ons |
| JTAG/SWD Application Voltage | 3 V to 3.6 V (5 V tolerant inputs) |
| SWIM Application Voltage | 1.65 V to 5.5 V (with adapter board MB1440) |
| VCP Application Voltage | 3 V to 3.6 V (5 V tolerant inputs) |
| VCP Frequency | Jiska 15 MHz |
| Entèfas USB | USB 2.0 high-speed (Micro-B connector) |
8. Enfòmasyon sou Garanti
For detailed warranty information regarding the STLINK-V3SET, please refer to the official STMicroelectronics websit la oswa dokiman ki vini ak acha ou a. Tèm garanti yo anjeneral kouvri domaj fabrikasyon pou yon peryòd espesifik apati dat acha a.
Protection plans may be available from third-party providers. For example, 2-Year and 3-Year Protection Plans are offered, as well as a Complete Protect plan. These are separate from the manufacturer's warranty.
9. Sipò teknik
For technical assistance, documentation, software downloads, and community forums, please visit the official STMicroelectronics support website. You can find resources related to the STLINK-V3SET, STM8, and STM32 microcontrollers.
STMicroelectronics Official Websit: www.st.com
