Manyèl Itilizatè Transmetè Kontwòl Remot BENINCA TO.GO 2WV

Entwodiksyon

This manual provides instructions for the BENINCA TO.GO 2WV remote control transmitter. This device is designed for controlling compatible BENINCA gate or garage door openers. Please read this manual thoroughly before use to ensure proper operation and safety.

Enfòmasyon sou Sekirite

• Kenbe kontwòl remote la lwen timoun yo pou anpeche li fonksyone aksidantèlman.
• Pa ekspoze aparèy la nan dlo, imidite twòp, oswa tanperati ekstrèm.
• Jete pil itilize yo byen selon règleman lokal yo.
• Always ensure the area around the gate or garage door is clear of people, pets, and obstructions before operating the system.

Pwodwi souview

The BENINCA TO.GO 2WV is a compact 433.92Mhz rolling code keyfob equipped with two buttons, allowing control over two distinct functions of your BENINCA automated system. Its design prioritizes ease of use and portability.

Image: The BENINCA TO.GO 2WV remote control, featuring a black casing and two prominent white control buttons. The 'TO.GO' branding is visible below the buttons.

Enstalasyon ak pwogramasyon

The BENINCA TO.GO 2WV remote control utilizes a rolling code system and must be programmed directly to your BENINCA receiver unit or control board. The specific programming procedure varies depending on your BENINCA gate or garage door opener model.

General Programming Steps (Consult your receiver's manual for exact instructions):

1. Access the Receiver: Locate the programming button or menu on your BENINCA gate/garage door opener's control board. This may require opening the control unit casing.
2. Aktive mòd pwogramasyon: Press and hold the programming button on the receiver until an indicator light (LED) changes state (e.g., starts flashing).
3. Transmit Code: While the receiver is in programming mode, press and hold the desired button on your new BENINCA TO.GO 2WV remote control for a few seconds.
4. Konfime Pwogramasyon an: The receiver's indicator light should change again (e.g., turn solid or flash rapidly) to confirm successful programming.
5. Operasyon tès: Once programmed, test the remote control to ensure it operates the gate or garage door correctly.
6. Program Additional Remotes: Repete pwosesis la pou nenpòt lòt kontwòl remote.

Important: Always refer to the specific instruction manual for your BENINCA gate or garage door opener's receiver for detailed and accurate programming steps.

Operasyon

To operate your BENINCA TO.GO 2WV remote control, simply press the programmed button corresponding to the desired function (e.g., open/close gate, open/close garage door). Ensure you are within the operational range of the receiver for reliable communication.

Antretyen

Ranplasman batri:

The remote control is powered by a standard coin cell battery. When the remote's operational range decreases or the indicator light (if present) fails to illuminate upon button press, the battery may need replacement.

1. Louvri kontwòl remote la avèk prekosyon casing, typically by prying it apart at a seam using a small flat-head screwdriver.
2. Note the orientation of the existing battery before removal.
3. Remove the old battery and insert a new one of the same type (e.g., CR2032), ensuring correct polarity (+ side up).
4. Fèmen kontwòl remote la casinbyen fèm jiskaske li tande yon klik nan plas li.

Netwayaj:

Wipe the remote control with a soft, dry cloth to remove dust or smudges. Do not use abrasive cleaners, solvents, or immerse the device in liquids, as this can damage the electronics.

Depanaj

• Remote pa travay: Verify the battery is correctly installed and charged. Ensure the remote is properly programmed to your receiver. Check if the receiver unit has power and is functioning correctly.
• Ranje redwi: This often indicates a low battery. Replace the battery. Ensure there are no significant physical obstructions (e.g., thick walls, metal structures) between the remote and the receiver.
• Entèferans: Other radio frequency devices in the vicinity might cause interference. Try operating the remote from a slightly different position or distance.
• Operasyon ki pa kòrèk: If the remote activates the wrong function or behaves erratically, re-program the remote control following the detailed steps in your receiver's manual.

Espesifikasyon

Garanti ak sipò

For specific warranty information, technical assistance, or to purchase replacement parts, please contact your authorized BENINCA product supplier or refer to the documentation originally provided with your BENINCA gate or garage door opener system. It is advisable to retain your purchase receipt for any warranty claims.