1. Pwodwi souview
The AMT 368C-95 is a .75" x .5" Cast Iron Straight Centrifugal Pump, featuring a Buna-N Seal and a 1/2hp 3 Phase Motor. It is designed for continuous-duty low pressure OEM, industrial/commercial, and general service applications.
Karakteristik kle yo enkli:
- Designed for continuous-duty low pressure OEM, Industrial/Commercial & General Service Applications
- Applications including circulation, chemical processing, liquid transfer, dirty water and cooling
- Pull-from-rear design for easy service without disturbing any piping; Self-Cleaning Impeller
- Pumps are close coupled to TEFC motors; Pumps are NOT self-priming & require flooded suction
- Cast Iron with SS, Self-Cleaning Impeller; Discharge Rotates in 90 Degree Increments
Figure 1: The AMT 368C-95 Cast Iron Straight Centrifugal Pump. This image shows the pump assembly with its motor, cast iron housing, and the inlet/outlet ports.
2. Enfòmasyon sou Sekirite
Limit responsabilite nou legal:
This item, component, package or system is intended for professional use only, by persons knowledgeable of how to determine if it is chemically compatible with the liquid(s) to be pumped, the safe installation, use and maintenance of pressure-generating and pressure-containing devices and the safe installation, use and maintenance of electrically, pneumatically and hydraulically powered equipment.
Always ensure proper electrical grounding and adhere to local electrical codes. Disconnect power before performing any maintenance or service.
3. Enstalasyon ak Enstalasyon
3.1. Preparasyon sit
Ensure the installation site is stable, level, and capable of supporting the pump's weight (approximately 31 pounds). Provide adequate ventilation for the motor.
3.2. Piping Connections
The pump features a .75" x .5" connection. Ensure all piping is properly sized and supported to prevent strain on the pump. The discharge can rotate in 90-degree increments for flexible installation.
3.3. Koneksyon elektrik
This pump is equipped with a 1/2hp 3 Phase Motor, 230/460 VAC/60 Hz. Electric supply for ALL motors must be within +/-10% of nameplate voltage rating (e.g., 230V +/-10% = 207 to 253). Consult a qualified electrician for wiring. Ensure proper grounding.
3.4. Priming
Enpòtan: This pump is NOT self-priming and requires flooded suction. Ensure the pump casing and suction line are completely filled with liquid before starting the pump to prevent damage.
4. Operasyon Enstriksyon
4.1. Tcheke Pre-Operasyon
- Verifye tout koneksyon an sekirite epi san koule.
- Confirm the pump is properly primed (flooded suction).
- Ensure the power supply matches the motor's requirements.
4.2. Kòmanse ponp lan
Once all pre-operation checks are complete, apply power to the motor. The pump is designed for continuous-duty operation.
4.3. Aplikasyon
This pump is suitable for various applications including circulation, chemical processing, liquid transfer, dirty water, and cooling. The self-cleaning, semi-open, stainless steel impeller can handle solids up to 1/8" diameter.
Figure 2: Performance curves for various straight centrifugal pumps, including the 368 series. This chart illustrates the relationship between total head (pressure) and capacity (flow rate) at 3450 RPM (60 Hz), along with Net Positive Suction Head Required (NPSHr) values.
5. Antretyen
5.1. Verifikasyon woutin
- Regularly inspect for leaks around seals and connections.
- Monitor motor temperature and unusual noises.
- Check for any obstructions in the suction or discharge lines.
5.2. Impeller and Seal Service
The pump features a "pull-from-rear" design, allowing for easy service of the impeller and mechanical seal without disturbing the piping. The self-cleaning impeller helps prevent clogging, but periodic inspection for debris is recommended, especially when pumping dirty water.
The pump uses a Buna-N Mechanical Seal and O-ring. Optional Silicon Carbide Mechanical Seals are available for different applications.
5.3. Preparasyon pou ivè (si sa aplikab)
If the pump is exposed to freezing temperatures, drain all liquid from the pump casing using the front drain plug to prevent damage from ice expansion.
NAN. Depanaj
Seksyon sa a bay konsèy jeneral pou pwoblèm komen. Pou pwoblèm konplèks, konsilte yon teknisyen kalifye.
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Ponp pa kòmanse | No power, incorrect wiring, motor issue | Check power supply, verify wiring, consult electrician |
| Ti koule oswa pa gen koule | Pump not primed, clogged impeller/lines, air leak in suction | Ensure flooded suction, clear clogs, check suction line for leaks |
| Twòp bri oswa Vibration | Cavitation, bearing wear, misalignment, foreign object in pump | Ensure proper priming, inspect bearings, check alignment, clear pump |
| Leaking from seal | Worn mechanical seal, improper installation | Replace mechanical seal, ensure correct installation |
7. Espesifikasyon
| Atribi | Valè |
|---|---|
| Modèl | 368C-95 |
| Dimansyon pwodwi | 12.4 x 8.3 x 7.2 pous |
| Pwa atik | 31 liv |
| Manifakti | American Machine and Tool Company |
| Mak | Enkoni |
| Materyèl | Jete Iron |
| Kalite sele | Buna-N Mechanical Seal and O-ring |
| Motè | 1/2hp 3 Phase TEFC |
| Voltage | 230/460 VAC/60 Hz |
| Pousantaj maksimòm koule | 90 GPM (143.83 Lit Pa Minit) |
| Maksimòm tèt | 65 pye |
| Maksimòm Presyon Travay | 75 psi |
| Tanperati maksimòm | 180 F |
| Manyen solid | Up to 1/8" diameter |
Figure 3: Detailed dimensional drawing of the pump and motor assembly, along with a table providing specific measurements (A, B, C, E, L, W, H) and weight for various AMT pump models, including the 368 series.
8. Garanti ak sipò
For warranty information and technical support, please contact the manufacturer, American Machine and Tool Company, or your authorized distributor. Keep your purchase receipt and product model number (368C-95) handy when contacting support.
Refer to the official product page or manufacturer's website for the most current warranty terms and contact details.
