Philips 24675-1 40W Fliyoresan Lamp Manyèl Enstriksyon

Enfòmasyon enpòtan sou sekirite

Read all instructions carefully before installing or using the Philips 24675-1 fluorescent lamp. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• AVÈTISMAN: Risk pou chòk elektrik. Dekonekte kouran an anvan enstalasyon oswa antretyen.
• Asire lamp is compatible with your fixture's ballast and voltagkondisyon e (50 Vòlt).
• Do not use with dimmers unless specifically rated for fluorescent lamps and compatible with the ballast.
• Manch lamps carefully. Avoid dropping or subjecting them to impact.
• Dispose of fluorescent lamps according to local regulations, as they contain mercury.
• Do not operate in wet locations or where directly exposed to water.

Enstalasyon ak Enstalasyon

This section provides instructions for safely installing your Philips 24675-1 fluorescent lamp.

Zouti ak materyèl ki obligatwa:

• Philips 24675-1 Fluorescent Lamp
• Compatible fluorescent fixture
• Stepladder (if necessary)
• Safety gloves and eye protection

Etap enstalasyon:

1. Etap 1: Dekonekte kouran an. Locate the circuit breaker or fuse box that controls the power to the light fixture. Turn off the power completely. Verify power is off using a voltagyon aparèy pou fè tès elektwonik si li disponib.
2. Step 2: Remove Old Lamp (si sa aplikab). Si w ap ranplase yon l ki deja egzisteamp, carefully twist the old fluorescent tube 90 degrees and gently pull it out of the lampholders. Dispose of the old lamp byen.
3. Step 3: Insert New Lamp. Align the pins on both ends of the Philips 24675-1 fluorescent lamp with the slots in the lampholders of your fixture. Gently push the lamp nan lampsipò yo jiskaske peny yo byen chita.
4. Step 4: Rotate Lamp. Once seated, rotate the lamp 90 degrees until it locks securely into place. Ensure both ends are firmly connected and the lamp se ki estab.
5. Etap 5: Retabli kouran an. Yon fwa ke lamp is securely installed, restore power to the fixture from the circuit breaker or fuse box.
6. Step 6: Test Operation. Turn on the light switch to confirm the lamp eklere.

Figure 1: Philips 24675-1 40W Fluorescent Lamp. This image shows the tubular shape and standard pins of the fluorescent lamp, ready for installation into a compatible fixture.

Enstriksyon Operasyon

The Philips 24675-1 fluorescent lamp is designed for straightforward operation within a compatible fixture.

1. Limen/Etenyen: Use the wall switch or fixture switch to turn the lamp sou oswa koupe.
2. Tan chofe: Fluoresan lamps may require a brief warm-up period (a few seconds) to reach full brightness, especially in colder environments.
3. Operasyon nòmal: L laamp will provide consistent illumination once fully warmed up.

Note: Frequent switching on and off can reduce the lifespan of fluorescent lamps. For optimal longevity, avoid rapid cycling.

Antretyen

Proper maintenance ensures optimal performance and extends the life of your Philips 24675-1 fluorescent lamp.

• Netwayaj: Ensure power is off before cleaning. Gently wipe the lamp with a soft, dry, lint-free cloth. Do not use liquid cleaners or abrasive materials.
• Enspeksyon: Detanzantan enspekte lamp and fixture for any signs of damage, loose connections, or discoloration. If any issues are found, disconnect power and consult a qualified electrician.
• Ranplasman: Ranplase lamp when it reaches the end of its average rated life (2000 hours) or if it begins to flicker excessively, dims significantly, or fails to illuminate.
• Dispozisyon: Fluoresan lamps contain small amounts of mercury. Do not dispose of them in regular household trash. Consult your local waste management authority for proper recycling or disposal procedures.

Depanaj

If you experience issues with your Philips 24675-1 fluorescent lamp, gade pwoblèm ak solisyon komen sa yo:

Espesifikasyon pwodwi

Detailed technical specifications for the Philips 24675-1 40W Fluorescent Lamp.

• Nimewo Modèl: 24675-1
• Mak: Philips
• Kalite limyè: Fluoresan
• Wattage: 40 Watts
• Voltage: 50 Volts
• Fòm: Echafodaj (T)
• Klate: 140 Lumen
• Tanperati koulè: 2700 Kelvin
• Endèks rann koulè (CRI): 80
• Mwayèn lavi: 2000 èdtan
• Dimansyon pwodwi: 1.75 x 1.75 x 24.5 pous
• Pwa atik: 6.4 ons
• Itilizasyon espesifik: Lamp

Garanti ak sipò

For warranty information or technical support regarding your Philips 24675-1 fluorescent lamp, please refer to the official Philips websit la oubyen kontakte sèvis kliyan yo dirèkteman.

Note: Warranty terms and conditions may vary by region and retailer. Keep your purchase receipt for warranty claims.