Manyèl Enstriksyon Access Mini 10 Chif, Entèriptè Dip, Transmetè pou Ouvrè Pòtay Garaj ak Entèriptè ak Entèriptè 300 Frekans.

1. Entwodiksyon

This manual provides comprehensive instructions for the setup, operation, and maintenance of your Access Mini 10 Digit Codes Dip Switch Remote Garage Gate Opener Transmitter. Please read this manual thoroughly before using the device to ensure proper function and safety.

The Access Mini remote is designed to provide convenient and secure access to your garage or gate system operating on a 300 MHz frequency with 10-digit dip switch coding.

2. Enfòmasyon sou Sekirite

• Kenbe kontwòl remote la lwen timoun yo.
• Do not allow children to operate the gate or garage door opener.
• Operate the gate or garage door only when it is in full view epi san obstak.
• Sekirite batri: Ensure correct battery polarity during installation. Do not mix old and new batteries. Dispose of used batteries responsibly.
• This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

3. Pake kontni

Verifye ke tout atik yo prezan nan pakè ou a:

• Access Mini Remote Garage Gate Opener Transmitter
• Kle bag

4. Pwodwi souview

The Access Mini remote features a compact design with two primary buttons and an integrated flashlight.

Figi 1: Devan View of Access Mini Remote. This image displays the front of the remote control, showing the two oval-shaped buttons. The left button is labeled "DOOR" for gate/garage operation, and the right button is labeled "LIGHT" for activating the integrated flashlight. The model name "ACCESS-300" is printed below the buttons. A key ring is attached at the bottom.

Figi 2: Retounen View of Access Mini Remote. This image shows the rear side of the remote control. A white label with the FCC ID and compliance statement is visible. Two small screws are present, indicating how the casing can be opened for battery or dip switch access. A key ring is attached at the bottom.

Figi 3: Entèn View of Access Mini Remote. This image reveals the internal components of the remote control. The circuit board is visible, along with a 12V battery (GoldenPower brand). Crucially, a row of 10 small dip switches (labeled 1 through 10) is clearly shown, which are used for programming the remote's code. The flashlight LED is also visible on the left side.

5. Enstalasyon

5.1. Enstalasyon batri

1. Locate the two small screws on the back of the remote (refer to Figure 2).
2. Using a small Phillips head screwdriver, carefully remove the screws.
3. Gently separate the two halves of the remote casing.
4. Insert one 12V A23 battery into the battery compartment, ensuring correct polarity (+ and - terminals match the markings). Refer to Figure 3 for battery placement.
5. Carefully reassemble the remote casing and secure it with the two screws.

5.2. Dip Switch Programming

The Access Mini remote uses 10 dip switches to set its unique code. This code must match the code set on your existing garage door opener or gate receiver. You will need to access the dip switches on your existing opener/receiver to determine the correct settings.

Enpòtan: Before proceeding, ensure your existing opener/receiver is compatible with 300 MHz frequency and 10-digit dip switch coding.

1. Access Existing Opener/Receiver: Locate your existing garage door opener or gate receiver. Open its casing to expose the dip switches. Note the position of each of the 10 switches (ON/UP or OFF/DOWN). Some systems may use a third position (MIDDLE/NEUTRAL), which should be replicated if present.
2. Open Access Mini Remote: Follow steps 1-3 from "5.1. Battery Installation" to open your Access Mini remote and expose its internal dip switches (refer to Figure 3).
3. Match Dip Switch Settings: Carefully adjust the 10 dip switches on your Access Mini remote to exactly match the settings of your existing opener/receiver. Use a small, non-conductive tool (like a toothpick) to move the switches.
4. Reassemble Remote: Once the dip switches are set, carefully reassemble the remote casing and secure it with the two screws.

Your Access Mini remote is now programmed and ready for use.

6. Operasyon Enstriksyon

6.1. Opening/Closing Garage Door or Gate

Point the Access Mini remote towards your garage door or gate opener/receiver and press the button labeled PÒT (refer to Figure 1). The gate or garage door should activate.

6.2. Sèvi ak Flach la

To activate the integrated flashlight, press the button labeled LIMYÈ (refer to Figure 1). Press it again to turn the flashlight off.

7. Antretyen

7.1. Ranplasman batri

When the remote's range decreases significantly or the LED indicator (if present) becomes dim, it's time to replace the battery. Follow the "5.1. Battery Installation" steps to replace the 12V A23 battery.

7.2. Netwayaj

Wipe the remote with a soft, dry cloth. Do not use abrasive cleaners or allow moisture to enter the casing.

NAN. Depanaj

9. Espesifikasyon

• Mak: Aksè
• Frekans: 300 MHz
• Kodaj: 10-Digit Dip Switch
• Kalite batri: 1 x 12V A23 (Alkaline)
• Pwa atik: 1.48 ons (apeprè 42 gram)
• Dimansyon pake: 6.18 x 3.58 x 0.98 pous (apeprè 15.7 x 9.1 x 2.5 cm)
• Karakteristik espesyal: Ergonomic design, Integrated Flashlight
• Aparèy konpatib: Garage Door Openers, Gate Openers (with matching frequency and dip switch coding)

10. Garanti ak sipò

For warranty information or technical support, please refer to the documentation provided with your purchase or contact the retailer/manufacturer directly. Keep your proof of purchase for warranty claims.

Pou plis asistans, ou ka vizite Access Store on Amazon.