Greenlee 14722 Knockout Punch Die Instruction Manual

1. Entwodiksyon

This manual provides essential instructions for the safe and effective use, setup, operation, and maintenance of the Greenlee 14722 Knockout Punch Die. Please read this manual thoroughly before operating the tool to ensure proper function and user safety. The Greenlee 14722 is designed for creating clean, accurate holes in metal materials.

2. Enfòmasyon sou Sekirite

AVÈTISMAN: Si ou pa swiv enstriksyon sekirite sa yo, ou ka blese gravman oswa domaje materyèlman.

• Always wear appropriate personal protective equipment (PPE), including safety glasses, gloves, and hearing protection, when operating knockout punches.
• Asire w ke pyès travay la byen klèamped before punching to prevent movement and potential injury.
• Never operate the punch near flammable materials or in explosive atmospheres.
• Kenbe men ak dwèt yo lwen zòn pwenson an ak mwazi a pandan w ap opere.
• Use only Greenlee-approved punches, dies, and draw studs that are compatible with your driver.
• Inspect the punch and die for damage or wear before each use. Do not use damaged equipment.
• Kenbe timoun yo ak moun ki t ap gade yo lwen zòn travay la.

3. Pwodwi souview

The Greenlee 14722 is a standard replacement die designed for use with Greenlee knockout punches. It is part of a complete unit that includes a punch, die, and draw stud, all necessary for creating precise holes in various metal materials. This die is specifically designed for 1/2 inch conduit/pipe size applications.

Karakteristik kle:

• Designed for use with battery-powered, hydraulic, ratchet, or manual drivers.
• Facilitates clean, fast, and accurate holes when properly assembled through pilot holes.
• Suitable for use on mild steel up to 10 gauge (check specific punch specifications for exact capacity).
• Slug-Buster compatible for efficient slug removal.

Figi 1: Top view of the Greenlee 14722 Knockout Punch Die, showing the internal cutting edge.

Figi 2: Side view of the Greenlee 14722 Knockout Punch Die, displaying the Greenlee logo and model number.

4. Enstalasyon

1. Select Components: Ensure you have the correct Greenlee punch and draw stud that match the 14722 die for the desired hole size.
2. Prepare pyès travay la: Mark the center of the desired hole location on the metal material. Drill a pilot hole at this mark. The pilot hole size must be appropriate for the draw stud being used.
3. Asanble Pwenson an ak Moul la:
   • Insert the draw stud through the pilot hole from the side of the material where the punch will be placed.
   • Thread the punch onto the draw stud on one side of the material.
   • Thread the 14722 die onto the draw stud on the opposite side of the material, ensuring the cutting edge faces the material.
4. Connect Driver: Attach your chosen driver (manual, ratchet, hydraulic, or battery-powered) to the draw stud.

5. Operasyon Enstriksyon

1. An sekirite pou pyès travay la: Ensure the material is firmly held in place to prevent shifting during the punching process.
2. Aliyen Konpozan yo: Verify that the punch, die, and draw stud are correctly aligned and centered over the pilot hole.
3. Angaje Chofè a: Operate the driver according to its specific instructions. Apply steady, even pressure to draw the punch through the material.
4. Complete Punch: Continue operating the driver until the punch fully cuts through the material and the slug falls into the die.
5. Remove Slug: Once the hole is cut, loosen the draw stud and remove the punch and die. The slug will typically fall free from the die with a quick tip.
6. Inspect Hole: Check the newly punched hole for cleanliness and accuracy.

6. Antretyen

• Netwayaj: After each use, clean the die and punch to remove any metal shavings or debris. A stiff brush or compressed air can be used.
• Lubrifikasyon: Apply a light coat of oil to the cutting edges of the die and punch to prevent rust and ensure smooth operation.
• Enspeksyon: Regularly inspect the die for signs of wear, dullness, or damage to the cutting edge. A dull die can lead to poor cuts and increased effort.
• Depo: Store the die in a clean, dry place to protect it from moisture and corrosion.

NAN. Depanaj

Pwoblèm komen ak solisyon:

• Poor Cut Quality / Burrs:
  • Ensure the punch and die are correctly aligned and tightened.
  • Check if the die or punch is dull or damaged; replace if necessary.
  • Verify the material thickness is within the tool's specified capacity.
• Difficulty Clearing Slugs:
  • Ensure the slug falls freely into the die. If using a Slug-Buster system, verify its proper function.
  • Clean any debris from the die cavity.
• Fòs twòp ki nesesè:
  • Lubricate the draw stud threads.
  • Check for dullness or damage to the punch and die.
  • Confirm the material thickness is not exceeding the tool's capacity.

8. Espesifikasyon

9. Enfòmasyon sou Garanti

Goods manufactured by Greenlee Textron are warranted to be free from defects in workmanship and material for a period of one year from the date of user purchase. This warranty is valid provided such goods are installed, operated, used, and maintained in accordance with Greenlee's written instructions. For specific warranty claims or details, please refer to the official Greenlee warranty policy or contact Greenlee customer support.

10. Sipò

For further assistance, technical support, or inquiries regarding the Greenlee 14722 Knockout Punch Die, please visit the official Greenlee website or contact their customer service department. Always refer to the model number (14722) when seeking support.