1. Entwodiksyon
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Philips HF-R 258 TL-D EII Electronic Ballast. This electronic ballast is designed for use with 58 Watt TL-D fluorescent lamps, operating on 220-240V, 50/60Hz electrical systems.
Tanpri li manyèl sa a byen anvan enstalasyon an epi konsève li pou referans pita.
2. Enfòmasyon sou Sekirite
Toujou obsève prekosyon sekirite sa yo:
- Danje elektrik: Installation and maintenance should only be performed by a qualified electrician. Ensure power is disconnected at the circuit breaker before any installation or servicing.
- Voltage konpatibilite: Verifye ke rezèv la voltage (220-240V, 50/60Hz) matches the ballast's requirements.
- Bon baz: Ensure the ballast is properly grounded to prevent electrical shock.
- Lamp Konpatibilite: Use only with compatible 58 Watt TL-D fluorescent lamps.
- Kondisyon anviwònman: Do not expose the ballast to excessive moisture or extreme temperatures.
3. Enstalasyon ak Enstalasyon
The Philips HF-R 258 TL-D EII electronic ballast is designed for easy integration into lighting fixtures. Follow the steps below for proper installation.
3.1. Dyagram fil elektrik
Gade dyagram sa a pou koneksyon elektrik ki kòrèk yo. Asire w tout koneksyon yo byen fèm epi yo konfòm ak kòd elektrik lokal yo.
Figi 3.1: Wiring diagram for the Philips HF-R 258 TL-D EII electronic ballast. This diagram illustrates the connections for the DC input (terminals 13, 14), AC input (terminals 8, 9), ground (terminal 10), and the lamp connections (terminals 1-7) for two TL-D lamps.
3.2. MCB Compatibility
The number of ballasts that can be connected to a Miniature Circuit Breaker (MCB) depends on the MCB type and rating. Consult the table below for guidance.
Figi 3.2: MCB compatibility table. This table provides information on the maximum number of ballasts relative to different MCB types (B, C, L, I, G, U, II, K, III) and their respective ratings (10A, 16A).
| Kalite MCB | Rating | Rating Relative Number of Ballasts |
|---|---|---|
| B | 16A | 100% |
| B | 10A | 63% |
| C | 16A | 170% |
| C | 10A | 104% |
| L, mwen | 16A | 108% |
| L, mwen | 10A | 65% |
| G, U, II | 16A | 212% |
| G, U, II | 10A | 127% |
| K, III | 16A | 254% |
| K, III | 10A | 154% |
4. Operasyon Enstriksyon
Once properly installed, the Philips HF-R 258 TL-D EII electronic ballast operates automatically to power compatible fluorescent lamps.
- Pouvwa sou: Apply power to the circuit. The ballast will initiate the lamps.
- Fonksyon gradyasyon: This ballast supports 1-10V dimming. Connect a compatible 1-10V dimmer to the designated dimming terminals (DC input terminals 13 and 14 as shown in the wiring diagram) to control the light output.
- Kòmanse instant: Electronic ballasts provide instant, flicker-free starting for fluorescent lamps.
5. Antretyen
The Philips HF-R 258 TL-D EII electronic ballast is designed for long-term, maintenance-free operation. However, general care and proper disposal are important.
- Netwayaj: If cleaning is necessary, disconnect power and wipe the ballast with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Lamp Ranplasman: Lè w ap ranplase lamps, ensure power is off. Replace with compatible 58 Watt TL-D fluorescent lamps.
- Resiklaj: Electronic ballasts and fluorescent lamps contain materials that should be recycled responsibly. Consult local regulations for proper disposal and recycling procedures.
For more information on recycling and cleaning, please refer to the manufacturer's guidelines or local waste management services.
NAN. Depanaj
If you experience issues with your Philips HF-R 258 TL-D EII electronic ballast, consider the following common problems and solutions:
- Lamps Not Lighting:
- Check the power supply to the ballast.
- Verifye ke lamps are correctly installed and are not faulty.
- Enspekte tout koneksyon fil elektrik yo pou wè si yo lach oswa domaje.
- Flickering Lamps:
- Asire lamps are fully seated in their sockets.
- Tcheke pou bon voltagekipman pou.
- Lamps may be at the end of their lifespan and require replacement.
- Fonksyon gradyasyon pa travay:
- Verify the 1-10V dimmer is compatible and correctly wired to the ballast's dimming terminals.
- Check the dimmer's power supply and functionality.
If problems persist, contact a qualified electrician or Philips Lighting customer support.
7. Espesifikasyon
Key technical specifications for the Philips HF-R 258 TL-D EII Electronic Ballast:
| Atribi | Valè |
|---|---|
| Mak | Philips Lighting |
| Manifakti | Philips |
| Nimewo Modèl | 91019630 |
| Dimansyon pwodwi (L x W x H) | 36 x 3 x 2.2 cm |
| Pwa atik | 299 g |
| Kantite Atik | 1 |
| Style | Modèn |
| Koulè | Blan |
| Fòm | Echafodaj (T) |
| Voltage | 230 Volts |
| Itilizasyon espesifik | Teknoloji ekleraj |
| Karakteristik espesyal | Dimmable (1-10V) |
| Kalite ploge | Kab elektrik |
| Pil enkli/obligatwa | Non |
| Konpatib Lamp Kalite | Fluorescent (TL-D) |
| Konpatib Lamp Wattage | 58 Watts (as per product title) |
| Enèji Label | 13 |
| Viv Mwayèn | 50000 èdtan |
Note: Some specifications in the source data, such as "Puissance: 90 Watts" and conflicting bulb base types (GX5.3, E27), appear to be generic or refer to other products. This ballast is specifically designed for 58 Watt TL-D lamps.
8. Garanti ak sipò
Warranty information for your Philips HF-R 258 TL-D EII electronic ballast is typically provided at the point of purchase or with the product packaging. Please retain your proof of purchase for warranty claims.
For technical support, service, or further inquiries, please contact Philips Lighting customer service or visit their official website. Contact details can usually be found on the product packaging or the manufacturer's websit.
