Manyèl Enstriksyon pou Bwat Gaming Antec NX400 NX Seri Mid-Tower ATX la

Entwodiksyon

The Antec NX400 is a versatile mid-tower ATX gaming case designed for PC enthusiasts and gamers. It offers a blend of aesthetic appeal with its tempered glass side panel and ARGB lighting, alongside practical features for component installation and cooling. This manual provides essential information for setting up, operating, and maintaining your Antec NX400 case.

Figi 1: Devan view of the Antec NX400 Mid-Tower ATX Gaming Case, showcasing its tempered glass side panel and front ARGB LED strip.

Karakteristik kle

• Sipò pou plak mèr: Compatible with ATX motherboards.
• Fanatik enkli: Features 1 x 120 mm ARGB fan pre-installed in the rear for immediate cooling and lighting.
• Sipò pou radyatè: Extensive liquid cooling support with space for up to a 360 mm radiator in the front, 240 mm on top, and 140 mm in the rear.
• Kondwi Bays: Supports versatile storage configurations with up to 2 x 3.5" HDDs / 2.5" SSDs (convertible) and 4 x 2.5" SSDs.
• Panèl bò: Equipped with a tempered glass side panel to showcase your internal components and ARGB lighting.
• Konektivite Panèl Devan an: Includes 1 x USB 2.0 port and 2 x USB 3.0 ports for convenient peripheral connection.
• Kontwòl ARGB: Dedicated LED mode button on the front panel allows for easy cycling through various ARGB lighting effects.

Figure 2: Detail of the multi-mode ARGB light bar on the front panel and the included 120mm ARGB fan in the rear of the NX400 case.

Figure 3: The dedicated LED control button located on the top I/O panel, allowing for easy customization of ARGB effects.

Enstalasyon ak Enstalasyon

Before beginning installation, ensure you have all necessary components and tools. Refer to your motherboard and component manuals for specific installation instructions.

1. Debalaj ak Preparasyon

• Retire bwat la nan anbalaj li avèk prekosyon.
• Remove the tempered glass side panel by unscrewing the four thumb screws. Place it on a soft, flat surface to prevent scratches.
• Identify the included accessory box containing screws and cable ties. Note that screws may be mixed; refer to component manuals for correct screw types.

2. Enstalasyon mèr

• Install the I/O shield (if not pre-attached to your motherboard) into the rear opening of the case.
• Align your ATX motherboard with the pre-installed standoffs inside the case.
• Secure the motherboard using the appropriate screws (typically those with a round head and a lip).

3. Enstalasyon Inite Alimantasyon (PSU)

• The NX400 supports PSUs up to 170 mm in length.
• Slide the PSU into the dedicated compartment at the bottom rear of the case.
• Secure the PSU from the rear of the case using the provided screws.

4. Enstalasyon Disk Depo

• Install 3.5" HDDs or 2.5" SSDs into the drive cages located beneath the PSU shroud or behind the motherboard tray.
• The case provides dedicated mounts for up to four 2.5" SSDs.

5. Enstalasyon Vantilatè ak Radyatè

• The case comes with one 120mm ARGB fan pre-installed in the rear.
• Additional fan support: Front (3 x 120mm or 2 x 140mm), Top (2 x 120mm or 2 x 140mm), Rear (1 x 120mm or 1 x 140mm).
• Radiator support: Front (up to 360mm), Top (up to 240mm), Rear (up to 140mm).

Figure 4: Diagram illustrating the fan and radiator mounting options within the Antec NX400 case.

6. Graphics Card and CPU Cooler Installation

• The case supports graphics cards up to 330 mm in length.
• CPU coolers with a maximum height of 170 mm are supported.

Figure 5: Internal layout showing maximum dimensions for CPU cooler, GPU, and PSU, along with motherboard and SSD/HDD locations.

7. Jesyon kab

• Utilize the cutouts and tie-down points behind the motherboard tray to route and secure cables for a clean build and improved airflow.
• Connect the front panel I/O cables (USB, audio, power, reset, LED) to the appropriate headers on your motherboard.
• Ensure the ARGB fan and front LED strip are connected. The fan typically uses a Molex connector, and the front LED strip uses a SATA power connector. These must be connected directly to your PSU.

Operasyon

The Antec NX400 features an intuitive front I/O panel for easy access to essential controls and ports.

Devan I/O Panel

• Bouton pouvwa: Peze pou limen oswa etenn sistèm nan.
• Bouton Reyajiste: Peze pou rekòmanse sistèm nan.
• Bouton kontwòl LED: Cycle through various pre-programmed ARGB lighting effects for the front LED strip and the included rear fan. A single press changes the effect.
• Pak MIKWO/ODYO: Connect your headphones and microphone.
• Pò USB 2.0 (x1): Pou konekte aparèy konpatib ak USB 2.0.
• Pò USB 3.0 (x2): For high-speed data transfer with USB 3.0 compatible devices.

Figi 6: Plis paseview of the top-mounted I/O ports, including power, reset, LED control, audio jacks, and USB ports.

Pwodwi souview Videyo

Antretyen

Regular maintenance helps ensure optimal performance and longevity of your Antec NX400 case.

• Netwayaj pousyè: Periodically clean dust filters (if present) and internal components using compressed air or a soft brush. This prevents dust buildup, which can impede airflow and component cooling.
• Swen vè apeze: Clean the tempered glass side panel with a microfiber cloth and a non-abrasive glass cleaner. Avoid harsh chemicals or abrasive materials that could scratch the glass.
• Jesyon kab: Detanzantan, tcheke chemen kab yo pou asire pa gen okenn kab k ap bloke sikilasyon lè a oswa lam vantilatè yo.

Depanaj

This section addresses common issues you might encounter with your Antec NX400 case.

1. ARGB Lighting Not Working or Incorrect Colors

• Tcheke Koneksyon: Ensure the front LED strip and the included ARGB fan are properly connected to their respective power sources (SATA for LED strip, Molex for fan) and to the case's internal LED controller.
• LED Button Functionality: Press the LED control button on the front I/O panel multiple times to cycle through effects. If no change occurs, verify the LED control cable is correctly connected to the motherboard or controller.

2. Twòp bri vantilatè

• Fanatik enkli: The included rear fan is connected via Molex, which typically means its speed is not controllable by the motherboard. If the fan is too loud, consider replacing it with a PWM or DC controllable fan connected to your motherboard.
• Obstak: Check for any cables or debris obstructing fan blades.
• Montaj: Ensure all fans are securely mounted to prevent vibrations.

3. Front Panel USB/Audio Ports Not Functioning

• Internal Connections: Verify that the USB and audio cables from the front I/O panel are securely connected to the correct headers on your motherboard. Refer to your motherboard manual for header locations.

4. Missing or Mixed Screws

• The case includes a single bag with various screw types. Refer to your component manuals (motherboard, PSU, drives) to identify the correct screws for each part. Common types include screws for motherboard standoffs (round head with lip), PSU mounting, and drive installation.

Espesifikasyon teknik

Garanti ak sipò

For warranty information, technical support, or service inquiries regarding your Antec NX400 case, please refer to the official Antec website or contact Antec customer support directly. Keep your proof of purchase for warranty claims.

Antec ofisyèl la Websit: www.antec.com