1. Pwodwi souview
The BELL HUBBELL WIRING 752 Square Flat Blank Angle Mounting Cover is designed to securely close an outlet box or provide a mounting surface for a device. Constructed from durable steel and finished in gray, this cover features angled mounting slots to facilitate precise alignment and compensate for minor box misalignments during installation.
Karakteristik kle:
- Objektif: Used to close an outlet box or mount a device.
- Angled Mounting Slots: Allows for correction of box misalignment, ensuring a flush and secure fit.
- Materyèl: Durable steel construction for longevity.
- Konfigirasyon: Square design.
Imaj 1.1: Devan view of the BELL HUBBELL WIRING 752 Square Flat Blank Angle Mounting Cover. This image displays the gray steel cover with its distinctive angled mounting slots at each corner, designed for secure and adjustable installation.
2. Enstalasyon ak Enstalasyon
This section provides instructions for the proper installation of your BELL HUBBELL WIRING 752 cover. Ensure all power is disconnected before beginning any electrical work.
- Sekirite Premye: Before starting installation, ensure the power supply to the electrical box is turned off at the circuit breaker. Verify with a voltage tèsteur.
- Prepare bwat la: Ensure the electrical box is clean and free of debris.
- Pozisyon kouvèti a: Place the BELL 752 cover over the electrical box, aligning the mounting slots with the screw holes on the box.
- Utilize Angled Slots: The angled mounting slots are designed to help correct minor misalignments of the electrical box. Adjust the cover slightly as needed to achieve a flush and level fit against the wall or surface.
- Sekirize kouvèti a: Insert appropriate mounting screws (not included) through the angled slots and into the electrical box. Tighten the screws firmly but do not overtighten, which could warp the cover or damage the box.
- Tcheke final la: Once secured, ensure the cover is flush and stable. Restore power to the circuit.
3. Operasyon Enstriksyon
The BELL HUBBELL WIRING 752 cover functions as a protective closure for an electrical box or a stable base for mounting other electrical devices. Once installed, its operation is passive.
- Pwoteksyon: The cover provides a physical barrier, protecting the internal wiring and components of the electrical box from dust, debris, and accidental contact.
- Montaj aparèy: If used for mounting a device, ensure the device is securely attached to the cover using appropriate fasteners.
4. Antretyen
The BELL HUBBELL WIRING 752 cover requires minimal maintenance to ensure its longevity and appearance.
- Netwayaj: Periodically wipe the cover with a soft, damp cloth to remove dust and dirt. Avoid abrasive cleaners or solvents, which may damage the finish.
- Enspeksyon: Annually inspect the cover for any signs of damage, corrosion, or loose mounting screws. Tighten screws if necessary, ensuring not to overtighten.
- Kowozyon: As the cover is made of steel, ensure it is not exposed to excessive moisture or corrosive environments unless specifically rated for such conditions.
NAN. Depanaj
This section addresses common issues you might encounter with the BELL HUBBELL WIRING 752 cover.
- Issue: Cover does not sit flush.
Solisyon: Loosen the mounting screws slightly. Utilize the angled mounting slots to adjust the cover's position until it sits flush. Retighten the screws. If the box itself is severely misaligned, professional electrical assistance may be required to adjust the box.
- Issue: Cover feels loose after installation.
Solisyon: Ensure the mounting screws are adequately tightened. Do not overtighten, as this can strip the screw threads in the electrical box. If the screw holes in the box are stripped, consider using larger screws or a repair kit for the electrical box.
- Issue: Visible corrosion or damage.
Solisyon: If the cover shows significant corrosion or damage, it should be replaced to maintain safety and aesthetic integrity. Ensure the environment is suitable for a steel cover.
6. Espesifikasyon
| Atribi | Detay |
|---|---|
| Nimewo Modèl | 752 |
| Mak | BELL (HUBBELL WIRING) |
| Materyèl | Steel |
| Koulè | Gri |
| Konfigirasyon | Kare |
| Kalite enstalasyon | Vis-nan |
| Dimansyon atik (L x W x H) | 4 x 4 x 0.5 pous |
| Pwa atik | 1.3 liv |
| Nimewo Pati Manifakti | 752 |
| UPC | 050169907528 |
7. Enfòmasyon sou Garanti
The BELL HUBBELL WIRING 752 Square Flat Blank Angle Mounting Cover comes with a manufacturer's warranty.
- Peryòd garanti: 1 ane
- Kouvèti: This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, misuse, abuse, or unauthorized modifications.
- Pwosesis reklamasyon: For warranty claims, please retain your proof of purchase and contact BELL customer support.
8. Sipò ak Kontak
For further assistance, technical support, or inquiries regarding your BELL HUBBELL WIRING 752 cover, please contact the manufacturer.
- Manifakti: HUBBELL WIRING
- Mak: KÒLÈ
- Resous sou entènèt: Vizite BELL ofisyèl la websit pou jwenn enfòmasyon sou pwodwi ak sipò.
- Sèvis Kliyan: Refer to the packaging or the manufacturer's websit pou jwenn enfòmasyon kontak aktyèl (telefòn, imèl).
