1. Entwodiksyon
This manual provides detailed instructions for the installation, operation, and maintenance of the Copeland XR02CX-5N0C1 Temperature Controller. This device is designed for precise temperature management in refrigeration and freezing units, offering single output control for compressors and defrosting functions. Please read this manual thoroughly before installation and operation to ensure safe and efficient use.
2. Pwodwi souview
The XR02CX-5N0C1 is a compact and reliable temperature controller, featuring a clear digital display and intuitive controls. It is suitable for a wide range of indoor refrigeration applications.
2.1 Karakteristik kle
- Single output for compressor control and shutdown defrosting.
- NTC temperature sensor input for accurate measurements.
- Digital input for passive switch quantity.
- Bright 2-digit red LED display.
- Durable ABS matte flame-retardant plastic shell.
- Front panel protection level IP65.
2.2 Eleman
Pake pwodwi a tipikman gen ladan:
- XR02CX-5N0C1 Temperature Controller unit
- NTC Temperature Probe (optional, depending on SKU)
- Klip aliye pou enstalasyon panèl
3. Espesifikasyon
| Paramèt | Valè |
|---|---|
| Modèl | XR02CX-5N0C1 |
| Mak | Copeland (Dixell/Copeland) |
| Kalite Sòti | Single output (compressor control, shutdown defrosting) |
| Opsyon ekipman pou pouvwa | 12Vac/dc ± 10%, 24Vac/dc ± 10%, 230Vac ± 10%/50-60Hz, 110Vac ± 10%/50-60Hz (refer to nameplate) |
| Konsomasyon pouvwa | Max 3VA |
| Ekspozisyon | 2 red digital tubes, 14.2mm high |
| Antre | 1 NTC input (temperature sensor), range -40 ℃ to 110 ℃ |
| Antre dijital | Passive switch quantity |
| Sòti Relay | Compressor SPST A, 250Vac; 20 (8) A 250Vac (Max instantaneous 20A, rated 8A) |
| Shell Materyèl | ABS matte flame-retardant plastic |
| Dimensions (Front) | 32x74mm |
| Pwofondè | 60mm |
| Installation Size (Panel Opening) | 71x29mm |
| Protection Level (Overall) | IP20 |
| Protection Level (Front Panel) | IP65 |
| Batri enkli | Non |
| Sèvi ak Anviwònman | Andedan kay la |
| Sètifikasyon | CE |
| Orijin | Lachin tè pwensipal |
4. Enstalasyon
The XR02CX-5N0C1 controller is designed for panel mounting. Ensure all power is disconnected before proceeding with installation.
4.1 Panel Mounting
- Cut an opening of 71x29mm in the desired panel.
- Insert the controller into the opening from the front.
- Secure the controller using the provided mounting clips from the rear of the panel.
5. Dyagram fil elektrik
Refer to the diagram below for correct electrical connections. Ensure all wiring is done by a qualified professional and complies with local electrical codes. The power supply voltage must match the controller's specified voltage (e.g., 230V~ 50-60Hz for the 220V model).
Koneksyon tèminal:
- Tèminal 1-2: Hot Key connection.
- Tèminal 3-4: Digital Input for external signals.
- Tèminal 5-6: NTC Probe input (Room temperature sensor).
- Tèminal 7-8: Power Supply (Line, e.g., 230V~ 50-60Hz).
- Tèminal 8-9: Compressor Output (Comp).
6. Operasyon
The controller features a simple interface for setting and monitoring temperature.
6.1 Kontwòl Panel Front
- SET bouton: Abitye view and modify the setpoint temperature and access programming parameters.
- Bouton flèch moute: Increases the displayed value or navigates through parameters.
- Bouton flèch desann: Decreases the displayed value or navigates through parameters.
- Bouton AUX: Typically used for auxiliary functions or to initiate manual defrost cycles.
- Ekspozisyon: Shows the current temperature or parameter values.
6.2 Setting the Temperature Setpoint
- Peze a SET button briefly to display the current setpoint.
- Peze epi kenbe la SET button for a few seconds until the setpoint value starts flashing.
- Sèvi ak la Up or Desann bouton flèch yo pou ajiste pwen konfigirasyon an nan tanperati ou vle a.
- Peze a SET Peze bouton an ankò pou konfime epi sove nouvo pwen konfigirasyon an.
6.3 Dekonjle
The controller supports shutdown defrosting. Consult the full programming manual (if available) for detailed defrost cycle settings. Manual defrost can typically be initiated by pressing and holding the AUX bouton.
7. Antretyen
Antretyen regilye asire lonjevite ak pèfòmans optimal kontwolè tanperati ou a.
7.1 Netwayaj
- Netwaye panèl la devan ak yon mou, damp twal. Pa sèvi ak pwodui netwayaj abrazif oswa solvang.
- Ensure no liquids enter the controller unit, especially around the buttons and display.
7.2 Probe Inspection
- Periodically check the NTC temperature probe and its wiring for any signs of damage or corrosion.
- Ensure the probe is securely placed in the area where temperature needs to be measured.
7.3 Koneksyon elektrik
- Occasionally inspect all electrical connections to ensure they are tight and free from corrosion.
- If any wiring appears damaged, replace it immediately.
NAN. Depanaj
Seksyon sa a bay solisyon pou pwoblèm komen ou ka rankontre.
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Kontwolè pa limen | Pa gen ekipman pou kouran; vòltaj ki pa kòrèktage; fil elektrik ki lach. | Check power source; verify voltage matches controller; inspect wiring connections. |
| Lekti tanperati ki pa kòrèk | Faulty NTC probe; probe not correctly installed; wiring issue. | Check probe connection; ensure probe is in correct location; replace probe if damaged. |
| Compressor not engaging/disengaging | Setpoint issue; relay fault; wiring to compressor incorrect. | Verify setpoint and differential settings; check compressor wiring; consult a technician if relay is suspected faulty. |
| Ekspozisyon montre kòd erè | Sensor error; internal fault. | Refer to the full programming manual for specific error code meanings. Check sensor connections. |
9. Konsèy itilizatè yo
- Always ensure the power supply is stable and within the specified voltage range to prevent damage to the controller.
- For optimal temperature control, place the NTC probe in a location that accurately reflects the temperature of the controlled environment, away from direct airflow or heat sources.
- Familiarize yourself with the programming parameters to fine-tune the controller's behavior for your specific application.
- Nan ka pouvwa outages, most controllers retain their settings, but it's good practice to verify the setpoint once power is restored.
10. Garanti ak sipò
For warranty information and technical support, please refer to the documentation provided with your purchase or contact your supplier. Keep your purchase receipt as proof of purchase.
