Universal RX-MULTI Remote Control Receiver

Entwodiksyon

The Universal RX-MULTI Receiver is a versatile 2-channel relay module designed to enhance or replace existing remote control systems for various applications. It operates across a wide frequency range of 300MHz to 868MHz and supports multiple encoding methods including Fixed Code, Rolling Code, and Learning Code. This receiver is ideal for controlling garage doors, gate openers, electric doors, windows, lifting equipment, and alarm systems, offering compatibility with a broad spectrum of remote control brands.

Figure 1: RX-MULTI Receiver Overview

Espesifikasyon

Kontni pake

• RX-MULTI Receiver
• Ti antèn
• Manyèl angle

Note: Remote control batteries (CR2016x2, 3V) are not included with the remote control unit.

Figi 2: Egzample Remote Control (not included with receiver only purchase)

Enstalasyon ak Enstalasyon

Câblage reseptè a

The RX-MULTI receiver features terminals for power (PWR), two channels (CH1, CH2), ground (GND), and antenna (ANT). Connect the receiver to your gate automation system, garage door opener, or other device according to its specific wiring requirements. Ensure proper polarity for DC power connections.

Figure 3: RX-MULTI Receiver Internal Components

Power Input Selection (PIS)

The receiver supports an operating voltage of AC/DC 9V-30V. Adjust the Power Input Selector (PIS) pins based on your power supply:

• Si opinyon an voltagSi e pi gran pase 24V, rakoursi broch 2 ak 3 yo.
• Si opinyon an voltagSi e mwens pase 24V, rakoursi broch 1 ak 2 yo.

Replacing an Old Receiver or Adding New Remotes

The RX-MULTI can replace an existing garage door receiver or be added to an existing system to increase the number of supported remote controls. It can store up to 400 remote controls, significantly expanding your system's capacity.

Figure 4: Receiver Application Scenarios

Enstriksyon pou pwogramasyon

To program a new remote control to the RX-MULTI receiver, follow these steps:

1. Select Remote Brand/Frequency: Identify the correct brand and frequency for the remote control you wish to program. Use the 8 dip switches on the receiver to set the corresponding combination (UP or DOWN). For example, for 433.92MHz Flor-s remote controls, move Dip-switch 8 UP. Refer to the provided diagrams for common configurations.
2. Initiate Learning Mode: Press the 'Learn' button on the receiver. The LED indicator will turn on, signifying that the receiver is in learning mode.
3. Program Remote Button: Press the desired button on your remote control. The receiver's LED will flash 4 times, indicating successful programming of that button.
4. Repete pou bouton adisyonèl yo: If your remote has multiple buttons you wish to program, repeat step 2 and 3 for each additional button.
5. Second Channel Programming: The programming procedure for the second channel (CH2) is identical to the first channel (CH1).

Figure 5: Dip Switch Settings Examples (Part 1)

Figure 6: Dip Switch Settings Examples (Part 2)

Erasing Tout Done ki Estoke yo

To erase all programmed remote controls from the receiver's memory:

• Peze epi kenbe youn nan bouton 'Aprann' ki sou reseptè a.
• The LED indicator will begin to flash. Continue holding the button.
• Release the button only after the LED turns off. All saved data will be permanently erased and cannot be recovered.

Operasyon Demonstrasyon

Depanaj

• Remote pa reponn: Ensure the remote control has fresh batteries. Verify that the dip switches on the receiver are correctly set for the remote's frequency and encoding type. Re-attempt the programming steps.
• Ranje limite: Check that the antenna is properly connected and extended. Ensure there are no major obstructions (e.g., thick walls, metal structures) between the remote and the receiver. Large electrical devices nearby can also cause interference.
• Programming failure: Double-check the dip switch settings. Ensure you are pressing the 'Learn' button correctly and observing the LED feedback. If multiple remotes are programmed, try erasing all data and reprogramming them one by one.
• No power to receiver: Verify the AC/DC 9V-30V power supply is connected correctly and providing the specified voltage. Check the Power Input Selector (PIS) pins are set appropriately for your voltage.

Konsèy itilizatè

Pa gen okenn konsèy espesifik pou itilizatè ki te disponib nan men reviews or Q&A for this product. However, general advice for remote control receivers includes:

• Always test the range of your remote control after installation to ensure reliable operation.
• Keep a spare remote control or ensure multiple users have access to prevent being locked out.
• If you experience intermittent issues, check for potential sources of radio frequency interference in the vicinity.

Antretyen

The RX-MULTI receiver is designed for low maintenance. To ensure optimal performance and longevity:

• Keep the receiver in a dry environment, away from direct moisture and extreme temperatures.
• Tcheke koneksyon fil elektrik yo detanzantan pou asire yo byen fèm.
• Avoid exposing the unit to strong impacts or vibrations.
• Clean the exterior with a soft, dry cloth if necessary. Do not use harsh chemicals or abrasive cleaners.

Sipò

Should you encounter any issues during the installation, programming, or operation of your RX-MULTI receiver, please contact the seller for assistance. Support is available for troubleshooting and guidance on product usage. If the product experiences a quality issue, a satisfactory resolution will be provided within the agreed timeframe.