LPSECURITY PY600ACN Sliding Gate Opener Control Board Instruction Manual
Model: PY600ACN (Compatible with SL600, PY600, PY800, SL1500 series)
1. Entwodiksyon
This manual provides detailed instructions for the installation, operation, and maintenance of the LPSECURITY PY600ACN series control board for sliding gate openers. This PCB circuit board is designed for 220V systems and supports NC (Normally Closed) limit switches, as well as magnetic limit switches. Please read this manual carefully before installation and operation to ensure safe and efficient use.
2. Enfòmasyon sou Sekirite
Ensure all power is disconnected before performing any installation, wiring, or maintenance.
Installation should be performed by qualified personnel to prevent electric shock or damage to the equipment.
Verifye voltage of your gate opener system (110V or 220V) matches the control board's specifications before connecting power.
Kenbe timoun ak bèt kay lwen zòn baryè a pandan w ap opere.
Do not attempt to repair the control board yourself. Contact a qualified technician for service.
3. Pwodwi souview
3.1 Eleman
The LPSECURITY PY600ACN control board is a central component for managing sliding gate operations. It integrates various functionalities for gate control and safety.
Figi 1: Top view of the PY600ACN control board, highlighting connection terminals and main components.Figi 2: Angle view of the control board, providing a clearer look at the power input and output sections.
3.2 Karakteristik kle
Kontwòl sèl bouton: A single button can execute all control commands (close, open, stop).
Individual Remote Control Deletion: Ability to delete specific remote controls separately.
Comprehensive Interface: Supports infrared sensors, solar energy connections, button switches, photocells, and backup batteries.
Infrared Detection Connector: Equipped with a dedicated connector for infrared detection.
Voltage Opsyon: Available in 110V and 220V versions.
Limit Switch Compatibility: Supports both mechanical and magnetic limit switches.
4. Espesifikasyon
Atribi
Valè
Non mak
LPSEKIRITE
Nimewo Modèl
PY600ACN (py)
Orijin
Lachin tè pwensipal
Sètifikasyon
CE
Sèvi ak
Sliding gate circuit board
Voltage
220V / 110V
Limit switch Kalite
Magnetic limit switch controller (NC)
Aplikasyon
Sliding gate door controller
Antre
Gate photocell lamp
Pwodui chimik ki gen anpil enkyetid
Okenn
Platfòm lakay entelijan
Okenn
5. Enstalasyon ak Enstalasyon
5.1 Wiring the Control Board
Carefully connect all components to the control board as per the wiring diagram. Ensure correct polarity and secure connections for all wires.
Figi 3: Egzample wiring connections on the control board. Note the green terminal blocks for various inputs and outputs.
5.2 Connecting the Limit Switch
The control board supports both mechanical and magnetic limit switches. Ensure the limit switch is properly connected and functioning. The video demonstrates connecting a magnetic limit switch and verifying its operation.
Video 1: Demonstration of connecting and testing the magnetic limit switch with the control board. Observe the LED indicators for proper function.
Steps for Limit Switch Connection and Test:
Connect the limit switch wires to the designated terminals on the control board.
Ensure the light on the control board corresponding to the limit switch is ON when the switch is activated (e.g., when the magnet is near the sensor).
Test the limit switch by manually moving the magnet past the sensor. The corresponding LED on the board should toggle ON/OFF.
5.3 Pè kontwòl remote
To pair a remote control with the control board:
Press the "LEARN" button on the control board (refer to Figure 1 for location). The learning LED should illuminate.
While the learning LED is on, press any button on your remote control. The LED should flash or change state to indicate successful pairing.
Test the remote control by pressing the programmed button. The gate motor should respond (e.g., start moving).
6. Operasyon Enstriksyon
Open/Close/Stop: Use the paired remote control or a connected button switch to operate the gate. A single press typically cycles through Open, Stop, Close, Stop.
Ijans Stop: In case of an emergency, press the remote control button again or the stop button to immediately halt the gate's movement.
7. Antretyen
Regularly inspect all wiring connections for signs of wear or damage.
Keep the control board clean and free from dust, moisture, and insects.
Check the functionality of the limit switches and safety sensors (e.g., photocells) periodically.
Ensure the remote control batteries are in good condition.
NAN. Depanaj
Pwoblèm
Kòz posib
Solisyon
Baryè a pa reponn a kontwòl remote la.
Remote not paired, remote battery low/dead, or incorrect remote.
Re-pair the remote control (Section 5.3). Replace remote battery. Ensure you are using the compatible remote control.
Gate does not stop at desired position.
Limit switch not properly connected or faulty.
Check limit switch wiring and functionality (Section 5.2). Adjust limit switch position if necessary.
Gate motor does not run.
No power to the board, motor wiring issue, or safety sensor activated.
Check power supply. Verify motor wiring. Ensure photocell or other safety sensors are not obstructed or faulty.
9. Konsèy itilizatè yo
Konpatibilite Remote Control: This control board is designed to work exclusively with LPSECURITY remote controllers. It is NOT compatible with other brands or universal remote controls.
Disponibilite Manyèl: The physical manual is not included in the package. Please request the digital manual from the seller via email after purchase.
Voltage and Limit Switch Type: Anvan achaasing or installing, always confirm that the control board's voltage (110V or 220V) and limit switch type (mechanical or magnetic) match your existing gate opener system.
10. Garanti & Sipò
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact LPSECURITY Automation and Security Official Store directly. Keep your purchase records for faster service.
