Ri M5STACKamPKontwolè lojik pwogramasyon LC IoT

Espesifikasyon

Spesifikasyon	Paramèt
Modil kontwòl	StampModil kontwòl S3A1, ki baze sou ESP32-S3FN8, gen ladan 8MB Flash, Wi-Fi 2.4GHz, Bluetooth Low Energy (BLE)
FLASH	8MB
Antre dijital	8 channels of opto-isolated digital inputs, input voltagranje: DC 5 ~ 36V
Sòti dijital	Sòti relè 4-chanèl
Relè	CA 5A @ 250V, CC 5A @ 28V
DC pouvwa Pwovizyon pou	supports DC 6~36V@1A wide voltage supply,DC power cornnector:DC5521 female,5.5x 2.1mm(center-positive)Expansion
n Interfaces	GPIO.EXT interface,2 Grove interfaces
Entèfas kominikasyon	Entèfas PWR-CAN ak PWR-485 entegre
PWR-CAN Interface	XT30(2+2)PW-M
PWR-485 Interface	HT3.96-4P
Ekspozisyon	Ekran koulè 1.14 pous (rezolisyon 135 × 240), fonksyone ak chip ST7789v2 la
Contro1 &Interaction	1 RESET/B00T button,3 user buttons, buzzer
Depo Done	Bati-an Micro SD emplacement kat
Detèktè	Capteur tanperati LM75, INA226 voltagCapteur kouran elektrik, RTC (RX8130CE)
Kapasite chaj pò I/0	Entèfas ekspansyon 2 × 8: kapasite maksimòm 1 chaj DC 4.76V @ 700mA, kapasite pò Grove 1 chaj: DC 4.81V ak 700mA
Konsomasyon pouvwa	Standby current:(5V supp1y)DC 5V@21.60mA,(12V supply)DC 12Ve15.22mA;Operating current:(5V supply)DC 5Ve93.89mA, (12V supply)DC 12V@47.84mA
Metòd enstalasyon	DIN tren aliye
Tanperati Fonksyònman	-10 ~ 50 ° C
Dimansyon pwodwi	72.0 × 80.0 × 31.7mm
Pwa pwodwi	139.4g
Dimansyon pake	102.0x94.0x37mm
Pwa Brit	163.7g
Manifakti	M5Stack teknoloji co, Ltd Blòk A10, Kòt Sid Expo Bay, Ri Fuhai, Distri Bao'an, Shenzhen, Lachin
Frequency Range for CE	2.4G Wi-Fi: 2412-2472MHz/2422-2462MHz BLE: 2402-2480MHz
Maksimòm EIRP pou CE	BLE: 6.84dBm 2.4G Wi-Fi: 17.90dBm

Enstriksyon Itilizasyon Pwodwi

Quick Start
Pou kòmanse avèk Stam PLC ou a, swiv etap sa yo:

ESKANE Wi-Fi

1. Lè l sèvi avèk ekipman pou kouran DC ki vini ak Stam PLC a, limen l.
2. Peze bouton RESET/BOOT la pou demarre aparèy la.
3. Access the Wi-Fi settings on your device and scan for available networks.
4. Select the appropriate Wi-Fi network and enter the password if required.
5. Once connected, you can start utilizing the wireless communication capabilities of the Stam PLC.

ESKANE BLE

1. Asire w ke PLC Stam lan limen epi li fonksyone byen.
2. Aktive paramèt Bluetooth yo sou aparèy ou an.
3. Chèche aparèy Bluetooth ki disponib tou pre a.
4. Select the Stam PLC from the list of discovered devices to establish a BLE connection.
5. You can now leverage the BLE functionality for data transfer and control.

DEBOU

Stam PLC se yon kontwolè lojik pwogramasyon IoT ki fèt pou automatisation endistriyèl ak siveyans a distans. Pwodwi a baze sou StampS3A control module, which not only delivers powerful processing capabilities but also provides efficient wireless connectivity. In terms of control, Stam PLC offers 8 opto-isolated digital inputs and 4 relay outputs (supporting both AC and DC loads), along with a
GPIO.EXT port and 2 Grove interfaces, making the integration of various sensors and actuators both simple and reliable. Meanwhile, through the onboard PWR-CAN and PWR-485 interfaces, the device can be seamlessly integrated into industrial fieldbus networks, enabling remote data transmission and centralized control.

For human-machine interaction, the product features a 1.14-inch color display, a RESET/BOOT button, 3 user buttons, and a buzzer, which facilitate real-time parameter configuration and status monitoring, and can alert users in the event of anomalies. To withstand harsh industrial environments, Stam PLC supports a wide voltage input (DC 6–36V) and is designed for DIN rail mounting to ensure secure installation; the built-in Micro SD card slot further facilitates data storage and firmware updates.

Additionally, its environmental monitoring system integrates an LM75 temperature sensor and an INA226 voltagCapteur e/kouran pou fidbak an tan reyèl sou operasyon aparèy la, pandan ke modil RTC (RX8130CE) la asire senkronizasyon tan egzat ak anrejistreman jounal. Firmwèr faktori a otomatikman telechaje done yo sou platfòm nwaj EZDATA M5 la, jenere paj siveyans epi ofri itilizatè yo aksè ak kontwòl nwaj adistans pratik. Pwodui sa a apwopriye pou automatisation endistriyèl, siveyans adistans, fabrikasyon entelijan, ak lòt aplikasyon.

Stam PLC

Kapasite kominikasyon

• Main Controller: ESP32-S3FN8 (StampS3A control module)
• Wireless Communication: Wi‑Fi (2.4 GHz) and Bluetooth Low Energy (BLE)
• CAN Bus: Onboard PWR‑CAN interface for reliable industrial data communication, RS-485:
• Onboard PWR‑485 interface supporting remote control via the Modbus RTU protocol

Processeur ak pèfòmans

• Processor Model: Xtensa LX7 dual-core (ESP32-S3FN8)
• Kapasite Depo: 8MB Flash
• Operating Frequency: Up to 240 MHz on a dual‑core 32-bit LX7 microprocessor

Ekspozisyon ak Antre

• Display: 1.14‑inch color TFT display for real‑time parameter monitoring
• Buttons: 1 RESET/BOOT button plus 3 user buttons for control and configuration. Buzzer:
• Built‑in buzzer for audio alerts and notifications
• RGB LED: Integrated RGB LED for dynamic visual feedback

Pins GPIO ak entèfas pwogramasyon

• GPIO Pins: Provides multiple configurable GPIO pins (detailed mapping available in documentation)
• Entèfas Ekspansyon:
  • 2 Grove interfaces for easy sensor and actuator connection
  • GPIO.EXT interface for additional connectivity
  • Micro SD card slot for data storage and firmware updates

Lòt moun

• Onboard Interfaces: Type‑C connector for programming, power supply, and serial communication
• Physical Dimensions: 72.0 × 80.0 × 31.7 mm with DIN rail mount design, suitable for harsh industrial environments
• Power Input: Wide voltage input ranging from DC 6–36V
• Integrated Sensors: Includes LM75 temperature sensor, INA226 voltage/current sensor, and RTC (RX8130CE) for accurate time synchronization and log recording
• Relay Outputs: 4‑channel relay outputs supporting AC 5A @ 250V / DC 5A @ 28V Opto-Isolated Digital Inputs: 8 channels designed to support DC 5–36V inputs for safe signal acq

Gwosè Modil

KÒMANSE RAPID

Before you do this step, look at the text in the final appendix: Installing Arduino.

Enprime enfòmasyon sou WiFi

1. Louvri Arduino IDE (Al gade nan https://docs.m5stack.com/en/arduino/arduino_ide pou gid enstalasyon pou tablo devlopman ak lojisyèl)
2. Select the ESP32S3 DEV Module board and the corresponding port, then upload the code.e
3. Louvri monitè seri a pou montre enfòmasyon sou Wi-Fi ak siyal yo analize.

KÒMANSE RAPID
Before you do this step, look at the text in the final appendix: Installing Arduin.

Enprime enfòmasyon BLE

1. Louvri Arduino IDE (Al gade nan https://docs.m5stack.com/en/arduino/arduino_ide pou gid enstalasyon pou tablo devlopman ak lojisyèl)
2. Chwazi tablo ESP32S3 DEV Modil la ak pò ki koresponn lan, Lè sa a, telechaje kòd la.
3. Louvri monitè seri a pou montre BLE analize ak enfòmasyon fòs siyal la.

Avètisman FCC

Atansyon FCC:
Nenpòt Chanjman oswa modifikasyon pati ki responsab pou konfòmite pa apwouve ekspreseman kapab anile otorite itilizatè a pou opere ekipman an.
Aparèy sa a konfòm ak pati 15 Règ FCC yo.

Operasyon an sijè a de kondisyon sa yo:

1. Aparèy sa a pa ka lakòz entèferans danjere, ak
2. Aparèy sa a dwe aksepte nenpòt entèferans resevwa, enkli entèferans ki ka lakòz operasyon endezirab.

REMAK ENPÒTAN:

Nòt: Yo te teste ekipman sa a epi yo jwenn li konfòme yo ak limit pou yon aparèy dijital Klas B, dapre pati 15 Règ FCC yo. Limit sa yo fèt pou bay pwoteksyon rezonab kont entèferans danjere nan yon enstalasyon rezidansyèl. Ekipman sa a jenere, itilize, epi yo ka gaye enèji frekans radyo epi, si li pa enstale ak itilize an akò ak enstriksyon yo, ka lakòz entèferans danjere nan kominikasyon radyo. Sepandan, pa gen okenn garanti ke entèferans pa pral rive nan yon enstalasyon an patikilye.

Si ekipman sa a lakòz entèferans danjere nan resepsyon radyo oswa televizyon, sa ki ka detèmine pa fèmen ekipman an epi limen, itilizatè a ankouraje pou eseye korije entèferans lan pa youn oswa plis nan mezi sa yo:

• Reoryantasyon oswa deplase antèn k ap resevwa a.
• Ogmante separasyon ki genyen ant ekipman ak reseptè a.
• Konekte ekipman an nan yon priz sou yon sikwi diferan de sa ki reseptè a konekte.
• Konsilte konsesyonè a oswa yon teknisyen radyo/televizyon ki gen eksperyans pou èd.

FCC Deklarasyon Ekspozisyon Radyasyon

Ekipman sa a konfòm ak limit FCC ekspoze a radyasyon ki tabli pou yon anviwònman san kontwòl. Ekipman sa a ta dwe enstale ak opere ak yon distans minimòm de 20cm ant radyatè a ak kò ou.

Arduino Enstale

Enstale Arduino IDE (https://www.arduino.cc/en/Main/Software)

Klike pou vizite ofisyèl Arduino la websit, epi chwazi pake enstalasyon an pou sistèm opere ou a telechaje.

Enstale Arduino Board Management

1. Manadjè Konsèy la URL yo itilize pou endèks enfòmasyon tablo devlopman pou yon platfòm espesifik. Nan meni Arduino IDE, chwazi File -> Preferans
2. Kopi jesyon tablo ESP URL pi ba a nan Manadjè Konsèy Lòt la URLs field, and save. https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Nan kad la, chwazi Manadjè Komisyon Konsèy, chèche ESP, epi klike sou Enstale.
4. Nan kad la, chwazi Manadjè Komisyon Konsèy, chèche M5Stack, epi klike sou Enstale.
   Tou depan de pwodwi yo itilize a, chwazi tablo devlopman ki koresponn lan anba Zouti -> Komisyon Konsèy -> M5Stack -> {ESP32S3 DEV Modil tablo}.
5. Konekte aparèy la nan òdinatè w lan ak yon kab done pou telechaje pwogram nan.

Kesyon yo poze souvan

Ki sa ki rekòmande opere voltage pou Stam PLC la?

Vol opere a rekòmandetage is between DC 6V to 36V with a current supply of 1A. Ensure to use a compatible DC power supply for optimal performance.

How can I expand the functionality of the Stam PLC?

You can expand the functionality by utilizing the GPIO pins and additional interfaces provided. Connect sensors and actuators to the Grove interfaces for enhanced capabilities.

Dokiman / Resous

Ri M5STACKamPKontwolè lojik pwogramasyon LC IoT [pdfGid Itilizatè StamPKontwolè lojik pwogramasyon LC IoT, Kontwolè lojik pwogramasyon IoT, Kontwolè lojik pwogramasyon, Kontwolè lojik

Referans

• Manyèl itilizatè