AXLAHA B0FZTXHFCX

AXLAHA Headlight Assembly Instruction Manual

Model: B0FZTXHFCX for 2014-2015 Chevrolet Silverado

Entwodiksyon

This manual provides detailed instructions for the installation, operation, and maintenance of your new AXLAHA Headlight Assembly. Designed specifically for 2014-2015 Chevrolet Silverado models, these headlight assemblies are engineered for optimal performance and durability. Please read this manual thoroughly before beginning installation to ensure proper fitment and safe operation.

Enfòmasyon sou Sekirite

  • Toujou dekonekte batri machin nan anvan ou fè nenpòt travay elektrik pou evite chòk elektrik oswa domaj.
  • Mete ekipman pwoteksyon pèsonèl ki apwopriye, tankou linèt sekirite ak gan, pandan enstalasyon an.
  • Ensure the vehicle is parked on a level surface with the parking brake engaged before starting any work.
  • Si ou pa sèten sou nenpòt etap nan pwosesis enstalasyon an, konsilte yon teknisyen otomobil ki kalifye.
  • Handle headlight bulbs with care. Avoid touching the glass portion of halogen bulbs with bare hands, as oils can cause premature failure.

Kontni pake

Verifye ke tout konpozan yo prezan anvan ou kòmanse enstalasyon an:

  • AXLAHA Headlight Assembly (Left)
  • AXLAHA Headlight Assembly (Right)
  • Manyèl Enstriksyon (Dokiman sa a)

Note: Headlight bulbs (HB3 High Beam, H11 Low Beam) are NOT included and must be purchased separately.

Enstalasyon ak Enstalasyon

Follow these steps carefully for proper installation of your new headlight assemblies.

1. Preparasyon

  1. Park your vehicle on a flat, level surface and engage the parking brake.
  2. Turn off the engine and remove the key from the ignition.
  3. Dekonekte tèminal negatif batri machin nan.
  4. Open the hood to access the headlight area.

2. Removing the Old Headlight Assembly

  1. Locate the mounting bolts/clips securing the existing headlight assembly. These are typically found on the top and side of the assembly.
  2. Carefully remove all securing hardware.
  3. Gently pull the old headlight assembly forward to disengage it from its mounting points.
  4. Disconnect all electrical connectors from the bulbs and the main harness. Twist and pull out bulbs if they are to be reused.
  5. Remove the old headlight assembly from the vehicle.

3. Installing Bulbs (If not pre-installed)

If your new AXLAHA Headlight Assembly does not come with bulbs, install them now. The assembly requires HB3 bulbs for high beam and H11 bulbs for low beam.

  1. Carefully insert the HB3 bulb into the high beam socket and twist to secure.
  2. Carefully insert the H11 bulb into the low beam socket and twist to secure.
  3. Ensure the bulbs are seated correctly and firmly.
Devan view of the AXLAHA headlight assembly showing clear lens, low beam, turn signal light, high beam, and safety reflector. Text indicates use of HB3 for high beam and H11 for low beam, and that bulbs are not included.

Figure 1: Front details of the headlight assembly, highlighting bulb types required.

Dèyè view of the AXLAHA headlight assembly showing the adjuster, one-way vent, and bulb protective film, with labels for low beam, turn signal light, and high beam connections.

Figure 2: Rear details of the headlight assembly, showing bulb access and adjustment points.

4. Installing the New Headlight Assembly

  1. Connect all electrical connectors from the vehicle's harness to the corresponding sockets on the new AXLAHA headlight assembly. Ensure connections are secure.
  2. Carefully slide the new headlight assembly into its mounting position, ensuring all tabs and alignment pins engage correctly.
  3. Reinstall all mounting bolts/clips that were removed earlier. Tighten them securely, but do not overtighten.
Overlay image showing the AXLAHA headlight assembly perfectly fitting into the front fascia of a Chevrolet Silverado.

Figure 3: Visual representation of the headlight assembly fitment on a Chevrolet Silverado.

5. Tcheke apre Enstalasyon

  1. Rekonekte tèminal negatif batri machin nan.
  2. Turn on the vehicle's headlights (low beam, high beam, turn signals) to ensure all functions are working correctly.
  3. Verify that the turn signals flash at the correct rate.
  4. Proceed to the "Headlight Aiming" section to adjust the beam pattern.

Enstriksyon Operasyon

Headlight Aiming

Proper headlight aiming is crucial for safe driving and to avoid blinding oncoming traffic. This assembly features an adjuster screw (refer to Figure 2) for vertical beam adjustment.

  1. Park your vehicle on a level surface approximately 25 feet (7.6 meters) from a wall or garage door.
  2. Ensure tire pressure is correct and the vehicle is not heavily loaded.
  3. Measure the height from the ground to the center of your low beam bulb. Mark this height on the wall.
  4. Turn on your low beam headlights.
  5. Using a Phillips head screwdriver, turn the adjuster screw (located on the rear of the headlight assembly, see Figure 2) to raise or lower the beam until the top edge of the brightest part of the beam is at or slightly below the marked line on the wall.
  6. Repete pou lòt limyè devan an.
  7. Horizontal adjustment is typically not required or available on most aftermarket assemblies. If horizontal adjustment is needed, it may require professional assistance.

Note: Always check local regulations for specific headlight aiming requirements.

Antretyen

Netwayaj

To maintain optimal light output and appearance, clean the headlight lenses regularly.

  • Use a soft cloth and mild automotive soap with water.
  • Avoid abrasive cleaners or harsh chemicals, as these can damage the lens or its UV protective coating.
  • Rense byen avèk dlo pwòp epi siye avèk yon twal mou ki pa gen pousyè.
Image illustrating the UV Block Clear Coat feature, showing a car with a clear headlight and a comparison of a hazy headlight before and a water-resistant surface after treatment.

Figure 4: The UV Block Clear Coat helps prevent yellowing and cracking, extending the life of the headlight.

Ranplasman anpoul

If a bulb fails, replace it promptly to ensure safe driving. Refer to the "Setup and Installation" section for general access to the bulbs.

  • Ensure the vehicle is off and the battery is disconnected.
  • Aksè dèyè asanblaj limyè devan an.
  • Twist the bulb socket counter-clockwise to remove the old bulb.
  • Disconnect the electrical connector from the bulb.
  • Connect the new bulb (HB3 for high beam, H11 for low beam) to the electrical connector.
  • Insert the new bulb into the housing and twist clockwise to secure.
  • Reconnect the battery and test the new bulb.

Depanaj

PwoblèmKòz posibSolisyon
Limyè pa macheBlown bulb, loose electrical connection, blown fuse, faulty wiring.Check and replace bulb. Ensure all electrical connectors are secure. Check vehicle's fuse box for blown headlight fuses. Inspect wiring for damage.
Limyè dim oswa flickeringLoose connection, failing bulb, insufficient power.Check electrical connections. Replace bulb. Consult a technician if power issues persist.
Moisture inside headlightCondensation (normal in some conditions), improper seal, damaged housing.Small amounts of condensation usually dissipate. Ensure all caps and seals are properly seated. If persistent or excessive, inspect for cracks or damage.
Improper beam aimIncorrect adjustment after installation.Refer to the "Headlight Aiming" section for adjustment procedures.

Espesifikasyon

  • Mak: AXLAHA
  • Modèl: B0FZTXHFCX
  • Konpatibilite: Chevrolet Silverado 2014-2015
  • Bulb Type (High Beam): HB3 (Not Included)
  • Bulb Type (Low Beam): H11 (Not Included)
  • Materyèl lantiy: Polycarbonate with UV Block Clear Coat
  • Rezistans move tan: Water, Snow, Dust Resistant (Refer to Figure 5)
Image showing the AXLAHA headlight assembly with water splashing, snow, and dust icons, emphasizing its waterproof capabilities.

Figure 5: The headlight assembly is designed to be water, snow, and dust resistant for reliable performance in various weather conditions.

Sipò pou Kliyan

For technical assistance, troubleshooting beyond this manual, or inquiries regarding your AXLAHA Headlight Assembly, please contact AXLAHA customer support through the retailer where the product was purchased.

Please have your product model number (B0FZTXHFCX) and purchase details ready when contacting support.

© 2023 AXLAHA. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.