Shutao 2 Channel 18650 Battery Capacity Tester User Manual

1. Entwodiksyon

This manual provides detailed instructions for the Shutao 2 Channel 18650 Battery Capacity Tester. This device is designed for comprehensive analysis of 18650 lithium batteries, offering independent charging, discharging, and capacity testing on two channels. It also includes internal resistance measurement capabilities, making it an essential tool for battery management and evaluation.

Karakteristik kle yo enkli:

• Independent Dual Channels: Simultaneously test two batteries without interference.
• Operasyon otomatik: Supports fully automatic charge and discharge cycles (1-9 cycles adjustable).
• Internal Resistance Test: Utilizes the DC two-wire method for reference internal resistance values.
• Pwoteksyon Sekirite: Overheating protection and automatic power-off with settings saved.
• Flexible Discharge Voltage: 11 selectable stop-discharge voltage levels (2.5V to 3.5V).
• Dual Type-C Power Input: Provides flexible power supply options.

Figure 1: Shutao 2 Channel 18650 Battery Capacity Tester overview.

2. Product Components and Interface

Familiarize yourself with the components and interface of the battery capacity tester before operation.

Figure 2: Labeled diagram of the tester's components.

1. Power Supply Battery Compartment: Slot for the device's power supply battery.
2. Charging Monitoring Indicator: Blue and red indicator light for the power supply battery's charging status. This does not relate to the test channels (8/9).
3. Type-C 5V Power Supply Interface: Primary power input for the device.
4. "ON/OFF/Menu" Button: Used for powering on/off and navigating menu options.
5. "Adjust" Button: Used to cycle through modes and adjust settings.
6. "Start/Stop" Button: Initiates or terminates a test cycle.
7. Test ② Type-C External Discharge Interface: Secondary Type-C port for external discharge testing.
8. Test ① Charging and Discharging 18650 Battery Compartment: Main slot for testing 18650 batteries.
9. 1.77 inch Display Screen: Shows real-time test data and settings.
10. 10W8ΩJ Discharge Cement Resistance x2: Resistors used for discharge load.

Note: Test ① (8) and Test ② (7) cannot be tested at the same time.

Figure 3: Display interface introduction.

1. Real Time Voltage: Montre vol aktyèl latage of the battery under test.
2. Real Time Current: Shows the current flowing during charge or discharge.
3. Pouvwa an tan reyèl: Indicates the instantaneous power.
4. Cumulative Capacity: Total capacity measured (mAh).
5. Accumulated Energy: Total energy measured (mWh).
6. Endikatè estati: Shows the current operational status (e.g., STA:STOP, STA:CHG, STA:DIS).
7. Modèl Travay: Indicates the current mode (e.g., MODE:AUTO, MODE:CHG, MODE:DIS).
8. Stop Discharge Voltage: Seri a voltage at which discharge will stop.
9. Sik: Number of completed charge/discharge cycles in AUTO mode.
10. Battery Internal Resistance: Reference internal resistance value (mR).
11. Tan kimilatif: Total time elapsed for the current test.

3. Enstalasyon

Follow these steps to set up your battery capacity tester for first use:

1. Koneksyon pouvwa: Connect the device to a 5V DC power source using a Type-C cable (not included) via the Type-C 5V Power Supply Interface (3).
2. Optional Power Supply Battery: For portable use or to power the device itself, insert a compatible battery into the Power Supply Battery Compartment (1). Note that this battery is for device power only and not for testing.
3. Battery Insertion for Test:
   • For 18650 batteries, insert the battery into the Test ① Charging and Discharging 18650 Battery Compartment (8), ensuring correct polarity.
   • For external batteries or devices, connect them to the Test ② Type-C External Discharge Interface (7).
4. Pouvwa sou: Press the "ON/OFF/Menu" button (4) to power on the device. The display screen (9) will illuminate.
5. Estabilizasyon: After installing a battery, wait a few seconds for the voltage and internal resistance readings to stabilize on the display before proceeding with tests.

Figure 4: Battery inserted into the test compartment.

4. Operasyon Enstriksyon

The tester offers various modes for battery analysis. Use the "ON/OFF/Menu" (4), "Adjust" (5), and "Start/Stop" (6) buttons to navigate and control operations.

4.1. Seleksyon mòd

Press the "Adjust" button (5) to cycle through the available modes:

• Mòd OTO: Performs a full charge-discharge cycle (or multiple cycles) to measure capacity.
• CHARGE Mode: Charges the battery to 4.2V.
• DISCHARGE Mode: Discharges the battery to a user-selected stop voltage.

4.2. Starting and Stopping Tests

Once a mode is selected and settings are configured (if applicable), press the "Start/Stop" button (6) to begin the test. Press it again to stop the test at any time.

When a test is stopped, a long press of the "Start/Stop" button (6) will reset the on-screen data.

4.3. AUTO Mode Operation

1. Insert the battery into the Test ① compartment (8) or connect to Test ② (7).
2. Press "Adjust" (5) until "MODE:AUTO" is displayed.
3. Use the "ON/OFF/Menu" button (4) to adjust the number of cycles (1-9) and the stop-discharge voltage (2.5V pou 3.5V).
4. Press "Start/Stop" (6) to begin. The tester will automatically charge, discharge, and recharge the battery for the set number of cycles, displaying cumulative capacity and energy.
5. The test will automatically stop when all cycles are completed.

4.4. CHARGE Mode Operation

1. Insert the battery into the Test ① compartment (8) or connect to Test ② (7).
2. Press "Adjust" (5) until "MODE:CHG" is displayed.
3. Press "Start/Stop" (6) to begin charging. The charging voltage is fixed at 4.2V.
4. Charging automatically stops when the battery is full.

4.5. DISCHARGE Mode Operation

1. Insert the battery into the Test ① compartment (8) or connect to Test ② (7).
2. Press "Adjust" (5) until "MODE:DIS" is displayed.
3. Use the "ON/OFF/Menu" button (4) to select the desired stop-discharge voltage (2.5V pou 3.5V).
4. Press "Start/Stop" (6) to begin discharging. The discharge current is fixed at approximately 1A.
5. Discharging automatically stops when the battery reaches the set stop voltage.

4.6. Internal Resistance Measurement

The tester provides a reference internal resistance value (mR) using the DC two-wire method. For the most accurate reading, measure when the battery is fully charged. The internal resistance is displayed on the screen (10).

5. Antretyen

• Netwayaj: Kenbe aparèy la pwòp epi san pousyè ak debri. Sèvi ak yon twal mou epi sèk pou netwaye.
• Depo: Sere aparèy tès la nan yon kote ki fre epi sèk, lwen limyè solèy dirèk ak tanperati ekstrèm.
• Manyen: Manyen aparèy la avèk prekosyon pou evite domaj fizik.
• Jesyon Chalè: The discharge load resistors (10) can get hot during operation. Ensure adequate ventilation and avoid touching them during or immediately after a test. The device includes active cooling and high-temperature protection.

NAN. Depanaj

• Inaccurate Internal Resistance Readings: If internal resistance readings appear high, especially at low battery voltages, try reinstalling the battery or measuring when the battery is fully charged for a more accurate result.
• Aparèy pa limen: Ensure the Type-C power cable is securely connected to a 5V DC power source, or that a charged battery is inserted into the Power Supply Battery Compartment (1).
• Test Not Starting: Verify that a battery is properly inserted with correct polarity and that a test mode has been selected. Press the "Start/Stop" button (6) firmly.
• Pa gen ekspozisyon: Check power connection. If the device is powered but the screen is blank, try pressing the "ON/OFF/Menu" button (4).
• Pwoblèm konpatibilite: This tester is not compatible with LiFePO4 batteries. Ensure you are testing compatible lithium-ion batteries (e.g., 18650 flat-top).
• Confusing Channel Operation: Remember that Test ① (18650 compartment) and Test ② (external Type-C) cannot be used simultaneously for testing.

7. Espesifikasyon

Figi 5: Dimansyon pwodwi a.

8. Garanti ak sipò

This product is manufactured by Shutao. For specific warranty information, please refer to the documentation provided with your purchase or contact the seller directly. General support inquiries can often be resolved by reviewing this manual or contacting the retailer where the product was purchased.

Tanpri konsève prèv acha ou a pou nenpòt reklamasyon garanti.