BSEED N020-120-1P

BSEED N020-120V-30A Surge Protector User Manual

Model: N020-120-1P

1. Entwodiksyon

The BSEED N020-120V-30A Surge Protector is a heavy-duty voltage regulator designed to protect your valuable home appliances from electrical fluctuations. It safeguards against high and low voltage, brownouts, spikes, instant surges, power failures, and load shedding. This device is suitable for a wide range of appliances, including refrigerators, air conditioners, TVs, computers, and other household electronics operating at 120V and up to 30A (3600W).

2. Enstriksyon Sekirite

Please read and understand all safety instructions before installing or operating this surge protector. Failure to follow these instructions may result in electric shock, fire, or damage to the product or connected appliances.

  • Danje elektrik: Ensure the power supply is disconnected before installation or making any adjustments.
  • Fil elektrik kòrèk: Always ensure the correct polarity of the cables (phase, neutral, grounding) during connection. Refer to the connection diagram for proper wiring.
  • Kapasite nominale: Do not exceed the maximum current capacity of 30 Amps or 3600 Watts. Overloading can cause damage and fire hazards.
  • Itilize andedan kay la sèlman: This device is intended for indoor use in dry locations. Do not expose to water or excessive humidity.
  • Koneksyon an sekirite: Ensure all wire connections are tight and secure to prevent arcing or overheating.
  • Enstalasyon pwofesyonèl: Si ou pa sèten sou pwosesis enstalasyon an, konsilte yon elektrisyen kalifye.
Connection Diagram for BSEED N020-120V-30A Surge Protector
Figi 2.1: Connection Diagram. This diagram illustrates the proper wiring for the surge protector, showing connections for electric supply, short circuit protector, and the equipment to be protected. Pay close attention to phase, neutral, and grounding connections for safety.

3. Pwodwi souview ak Karakteristik

3.1 Konpozan ak Endikatè Kle yo

Basic Characteristics of BSEED N020-120V-30A Surge Protector
Figi 3.1: Basic Characteristics. This image highlights the indicator lights on the surge protector: 1. Normal Voltage (Green), 2. Over Voltage (Orange), and 3. Low Voltage (Red). It also shows the adjustable voltage settings and reconnection delay.
  • Indicator of NORMAL voltage (Vèt): Illuminates when the voltage se nan seri operasyon an sekirite.
  • Indicator of OVER voltage (Orange): Li limen lè volim antre atage exceeds the set maximum threshold.
  • Indicator of LOW voltage (Wouj): Li limen lè volim antre atage drops below the set minimum threshold.
  • Reglabl Voltage Anviwònman: Dials for setting minimum (Under Voltage Cut-off) and maximum (Over Voltage Cut-off) voltage papòt yo.
  • Adjustable Reconnection Delay: Dial for setting the waiting time before power is reconnected after a voltage evènman.

3.2 Karakteristik avanse

Other Novel Features of BSEED N020-120V-30A Surge Protector
Figi 3.2: Other Novel Features. This diagram illustrates the internal components and features, including adjustable voltage and delay settings, manual ON/OFF switch, assembly facilities, safer connectors with protective covers, convenient access for gutters, and a protective cover with safety seal holes.
  1. Adjustable LOW voltage pèmèt: Chwazi ant 90V ak 115V.
  2. Adjustable OVER voltage pèmèt: Chwazi ant 125V ak 145V.
  3. Adjustable waiting cycle: Between 180-300 seconds (3 to 5 minutes).
  4. Manual ON and OFF switch: For convenient control.
  5. Assembly facilities: Two (2) options for mounting on a 2"x4" box or a flat surface.
  6. Safer connectors: Tèminal Antre ak pwodiksyon yo pwoteje ak yon kouvèti.
  7. Convenient access for gutters: Through predictable sections.
  8. Protective cover with safety seal holes: To prevent unauthorized manipulation of adjustments and connections.

3.3 Dimansyon pwodwi

Dimensions of BSEED N020-120V-30A Surge Protector
Figi 3.3: Product Dimensions. The surge protector measures approximately 3.50 inches in height, 4.60 inches in width, and 1.45 inches in depth.

4. Enstalasyon

4.1 Dyagram fil elektrik

Gade Figure 2.1 (Connection Diagram) in the Safety Instructions section for detailed wiring instructions. Ensure all connections are made correctly, matching phase (L), neutral (N), and grounding (G) wires from your electric supply to the protector's input terminals, and then from the protector's output terminals to your appliance.

4.2 Montaj

The surge protector can be mounted in two ways:

  • On a 2"x4" electrical box: Use the designated assembly facilities on the device.
  • Sou yon sifas ki plat: Secure the device using appropriate screws through the provided mounting holes.

4.3 Premye Enstalasyon ak Ajisteman

Before connecting your appliance, you can adjust the voltage cut-off points and the delay time:

  • Anba Voltage Koupe: Use the 'MINIMUM V-' dial to set the lowest acceptable voltage ant 90V ak 115V.
  • Plis pase Voltage Koupe: Use the 'MAXIMUM V+' dial to set the highest acceptable voltage ant 125V ak 145V.
  • Reconnection Delay: Use the 'RECONNECTION S' dial to set the waiting period (3 to 5 minutes) before power is restored after a voltage evènman.

It is recommended to set these values according to the specifications of the appliance you intend to protect and your local power grid stability.

5. Operasyon

5.1 Limen

After proper installation and adjustment:

  1. Ensure the manual ON/OFF switch is in the 'ON' position.
  2. Apply power to the surge protector.
  3. The device will initiate a delay cycle (3 to 5 minutes, as set). During this time, the indicator lights may show a waiting state.
  4. Once the delay period is complete and the voltage is stable within the set parameters, the green 'NORMAL' indicator light will turn on, and power will be supplied to your connected appliance.

5.2 Endikatè Limyè

  • Green Light (NORMAL): Endike ke voltage is stable and within the safe operating range, and power is being supplied to the appliance.
  • Orange Light (OVER VOLTAGE): Indicates that the input voltage is too high. The protector has cut off power to safeguard the appliance. Power will be restored after the voltage normalizes and the delay cycle completes.
  • Red Light (LOW VOLTAGE): Indicates that the input voltage is too low. The protector has cut off power to safeguard the appliance. Power will be restored after the voltage normalizes and the delay cycle completes.

5.3 Aplikasyon tipik

BSEED N020-120V-30A Surge Protector in various applications
Figi 5.1: Typical Applications. The BSEED N020-120V-30A Surge Protector is suitable for protecting a variety of heavy-duty home appliances, including air conditioners, washing machines, rice cookers, and microwave ovens.

6. Antretyen

The BSEED N020-120V-30A Surge Protector requires minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

  • Netwayaj: Periodically wipe the exterior of the device with a soft, dry cloth. Do not use liquid cleaners or solvents.
  • Tcheke Koneksyon: Chak ane, enspekte tout koneksyon fil elektrik yo pou asire yo rete sere epi san korozyon.
  • Kondisyon anviwònman: Ensure the device is kept in a dry, well-ventilated area, away from direct sunlight, heat sources, and corrosive environments.
  • Kouvèti pwoteksyon: Keep the protective cover securely closed to prevent dust and unauthorized access to internal components.

NAN. Depanaj

If you encounter issues with your surge protector, refer to the following common problems and solutions:

PwoblèmKòz posibSolisyon
Appliance does not power on after connecting.1. Surge protector is in delay cycle.
2. Antre voltage is outside safe range.
3. Manual switch is OFF.
4. Koneksyon fil elektrik ki lach.
1. Wait for the set delay time (3-5 minutes).
2. Check indicator lights (Orange for Over, Red for Low). Wait for voltage pou nòmalize.
3. Ensure the manual ON/OFF switch is in the 'ON' position.
4. Disconnect power and check all wiring connections for tightness.
Orange (Over Voltage) or Red (Low Voltage) light remains on.Persistent unstable voltage soti nan ekipman pou pouvwa a.The protector is functioning as intended by cutting off power. If the issue persists, contact your electricity provider or a qualified electrician to check your home's electrical system.
Device appears to be non-functional.Internal fault or severe damage.Disconnect from power immediately. Do not attempt to repair. Contact BSEED customer support for assistance.

8. Espesifikasyon teknik

SpesifikasyonValè
MakGRENN BSEED
Nimewo ModèlN020-120-1P
Voltage120V AC
Maksimòm Kouran30 Amps
Maksimòm pouvwa3600 Watts
Anba Voltage Cut-off RangeAdjustable 90V - 115V
Plis pase Voltage Cut-off RangeAdjustable 125V - 145V
Reconnection Delay TimeAdjustable 3 - 5 minutes (180-300 seconds)
Kantite plòg1
Kalite plogeType B - 3 pin (North American)
Aparèy konpatibAir Conditioner, Computer, House Electric Appliances, Refrigerator, Television
Materyèl patirajAliminyòm, Kuiv, Polikarbonat, Kawoutchou
Karakteristik espesyalReglabl Voltage, Surge Protection, Manual ON/OFF Switch

9. Kontakte ak Sipò

For further assistance, technical support, or warranty inquiries, please contact BSEED customer service through the retailer where the product was purchased or visit the official BSEED websit.

Manifakti: GRENN BSEED

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.