BDCOM S2900-24T4X-2AC Ethernet Layer-3 Lite Switch User Manual

1. Entwodiksyon

This manual provides essential information for the installation, operation, and maintenance of the BDCOM S2900-24T4X-2AC Ethernet Layer-3 Lite Switch. Please read this manual thoroughly before using the device to ensure proper setup and functionality. Retain this document for future reference.

2. Pwodwi souview

The BDCOM S2900-24T4X-2AC is a high-performance Ethernet Layer-3 Lite switch designed for various networking environments. It features 24 Gigabit Ethernet (GE) TX ports and 4 10 Gigabit Ethernet (10GE) SFP+ ports, providing flexible connectivity options. The switch also includes a console port for management and supports standard 19-inch rack-mounted installation.

2.1 Karakteristik kle

• 1 Console port for device management.
• 24 Gigabit Ethernet (GE) TX ports for high-speed network connections.
• 4 10 Gigabit Ethernet (10GE/GE) SFP+ ports for uplink or high-bandwidth connections.
• AC 110V ~ 220V input, 60 Hz power supply.
• Konsepsyon san fanatik pou operasyon an silans.
• 1U height, suitable for standard 19-inch rack-mounted installation.

2.2 Aranjman Panèl Devan an

Figure 1: Front Panel Diagram of BDCOM S2900-24T4X-2AC Switch, highlighting 24 Gigabit RJ45 ports, 4 10G/1G SFP+ ports, and the Console port.

• Pò konsole: Pò RJ45 pou aksè nan koòdone liy kòmand (CLI).
• GE TX Ports (1-24): 24 Gigabit Ethernet ports for connecting network devices.
• 10GE/GE SFP+ Ports (TE1-TE4): 4 SFP+ slots supporting 10 Gigabit or 1 Gigabit fiber optic transceivers.
• Endikatè ki ap dirije: System (SYS), Power (PWR), and individual port status indicators.

Figi 2: Devan detaye view of the BDCOM S2900-24T4X-2AC switch, showing the arrangement of ports and indicators.

2.3 Layout panèl dèyè

Figi 3: Dèyè view of the BDCOM S2900-24T4X-2AC switch, displaying the AC power input and power switch.

• AC pouvwa Antre: Connector for the AC power cord (100-240 VAC, 50/60 Hz).
• Pouvwa switch: On/Off switch for the device.

3. Enstalasyon

Follow these steps for proper installation of your BDCOM S2900-24T4X-2AC switch.

3.1 Preparasyon Sit

• Asire w ke kote enstalasyon an pwòp, sèk, epi byen ayere.
• Kenbe yon tanperati anbyen ant 0°C ak 50°C (32°F ak 122°F).
• Avoid direct sunlight, heat sources, and excessive dust.
• Ensure adequate space around the switch for proper airflow, especially at the sides where ventilation is located.

3.2 Montaj etajè

The switch is designed for standard 19-inch rack-mounted installation (1U height).

1. Attach the provided rack-mount brackets to the sides of the switch using the included screws.
2. Align the switch with the rack posts and secure it using appropriate rack screws.
3. Ensure the switch is level and securely fastened in the rack.

3.3 Koneksyon pouvwa

1. Ensure the power switch on the rear panel is in the OFF position.
2. Connect one end of the AC power cord to the power input on the rear panel of the switch.
3. Connect the other end of the AC power cord to a grounded power outlet (100-240 VAC, 50/60 Hz).
4. Flip the power switch to the ON position. The Power (PWR) LED on the front panel should illuminate.

3.4 Koneksyon rezo

• GE TX Ports: Connect standard RJ45 Ethernet cables from your network devices (servers, workstations, other switches) to the GE TX ports (1-24).
• 10GE/GE SFP+ Ports: Insert compatible SFP+ transceivers into the SFP+ slots (TE1-TE4). Connect fiber optic cables from other network devices or uplinks to these transceivers. Ensure the transceivers and cables match the required speed (1G or 10G).
• Pò konsole: For initial configuration and management, connect a console cable (RJ45 to DB9 or USB) from your management workstation to the console port.

4. Inisyal Konfigirasyon

The BDCOM S2900-24T4X-2AC switch can be configured via its Command Line Interface (CLI) through the console port or via a webEntèfas Itilizatè Grafik (GUI) ki baze sou .

4.1 Console Access (CLI)

1. Connect your computer to the switch's console port using a console cable.
2. Open a terminal emulation program (e.g., PuTTY, Tera Term) on your computer.
3. Configure the serial port settings:
   • Pousantaj Baud: 9600
   • Done Bits: 8
   • Parite: Okenn
   • One Stop Bits: 1
   • Kontwòl koule: Okenn
4. Power on the switch. The boot-up messages will appear in the terminal window.
5. Log in using the default credentials (refer to the official BDCOM documentation for default username and password).
6. Begin configuring the switch according to your network requirements. The command structure is similar to Cisco IOS.

4.2 Web-based Management (GUI)

Once the switch has an IP address configured (either manually via CLI or via DHCP), you can access its web koòdone.

1. Ensure your management computer is on the same network segment as the switch.
2. Louvri a web navigatè a epi antre adrès IP switch la.
3. Konekte avèk kalifikasyon apwopriye yo.
4. The GUI provides a user-friendly interface for configuring various switch functions. Note that the included PKI certificate may be expired, requiring generation of a new one for secure access.

For detailed command references and advanced configuration, please consult the official BDCOM S2900 series documentation.

5. Operasyon Enstriksyon

The BDCOM S2900-24T4X-2AC switch operates automatically once configured. Here are general operational guidelines:

• Limen/Etenyen: Use the power switch on the rear panel. Always ensure proper shutdown procedures if available through CLI/GUI before powering off.
• Endikatè ki ap dirije: Monitor the front panel LEDs for operational status:
  • PWR (pouvwa): Solid green indicates the switch is powered on.
  • SYS (Sistèm): Indicates system status (e.g., solid green for normal operation, blinking for activity or errors). Refer to the full manual for specific patterns.
  • Pò LEDs: Indicate link status and activity for each GE and SFP+ port.
• Koneksyon rezo: Ensure all connected devices are properly cabled and configured for network access.
• Layer-3 Lite Functionality: The switch supports basic Layer-3 routing capabilities. Configure VLANs, IP interfaces, and static routes as needed for inter-VLAN routing and network segmentation.
• Agregasyon Lyen (LACP): For increased bandwidth and redundancy, configure Link Aggregation Control Protocol (LACP) on multiple ports to form a single logical link (port channel). Ensure a lower value for the 'agg-period' parameter if configuring LACP.

6. Antretyen

Antretyen regilye ede asire lonjevite ak pèfòmans optimal switch ou a.

• Netwayaj: Netwaye deyò switch la detanzantan avèk yon twal mou epi sèk. Pa sèvi ak pwodui netwayaj likid oswa ayewosòl. Asire w ke ouvèti vantilasyon yo pa gen pousyè ak obstak.
• Mizajou mikrolojisyèl: Check the BDCOM official website for the latest firmware updates. Applying updates can improve performance, add features, and fix bugs. Follow the provided instructions carefully during firmware upgrades.
• Sovgad Konfigirasyon: Regularly back up your switch configuration to an external storage device. This allows for quick restoration in case of a device reset or failure.
• Siveyans anviwònman an: Asire w ke anviwònman operasyon an rete nan limit tanperati ak imidite espesifye yo.

NAN. Depanaj

Seksyon sa a bay solisyon pou pwoblèm komen. Pou pwoblèm ki pi konplèks, kontakte sipò teknik.

7.1 Pwoblèm pouvwa

• Pa gen pouvwa:
  • Verifye kòd kouran an byen konekte ak tou de switch la ak priz kouran an.
  • Asire w ke switch pouvwa a sou panèl dèyè a nan pozisyon ON.
  • Check the power outlet with another device to confirm it is functional.

7.2 Pwoblèm koneksyon rezo

• Pa gen lyen sou yon pò:
  • Check the Ethernet or fiber cable connection. Ensure it is securely plugged into both the switch port and the connected device.
  • Verify the cable is not damaged. Try a different cable.
  • Asire w ke aparèy ki konekte a limen epi li fonksyone byen.
  • Check the port status LEDs on the switch. If the LED is off, there might be no link.
  • For SFP+ ports, ensure the transceiver is correctly seated and compatible. The switch can be particular about transceivers.
• Pèfòmans Rezo Ralanti:
  • Check for network congestion.
  • Verify duplex and speed settings on the switch port and connected device.
  • Ensure cables are appropriate for the speed (e.g., Cat5e/6 for Gigabit Ethernet).

7.3 Management Access Issues

• Pa ka jwenn aksè nan CLI a atravè konsole a:
  • Verify the console cable connection.
  • Check the serial port settings in your terminal emulation program (Baud Rate, Data Bits, Parity, Stop Bits, Flow Control).
  • Asire w ke yo chwazi pò COM kòrèk la.
• Cannot Access GUI via Web Navigatè:
  • Verify the switch has an IP address and your computer can reach it (ping the IP address).
  • Asire w web browser is not blocking the connection due to certificate warnings (the default certificate may be expired).
  • Vide kach navigatè a oubyen eseye yon lòt navigatè.

8. Espesifikasyon

9. Enfòmasyon sou Sekirite

Obsève prekosyon sekirite sa yo pou evite blesi ak domaj nan aparèy la:

• Always connect the power cord to a grounded electrical outlet.
• Pa opere aparèy la nan mouye oswa damp kondisyon yo.
• Asire bon vantilasyon pou anpeche surchof.
• Pa louvri aparèy la casing. Konfye tout antretyen bay pèsonèl kalifye.
• Evite mete objè lou sou switch la.
• Dekonekte kouran an anvan ou netwaye oswa deplase aparèy la.

10. Garanti ak sipò

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official BDCOM websit la. Ou kapab kontakte revandè ou a tou pou jwenn asistans.

BDCOM Official Websit: www.bdcom.com.cn