LEDONE 8FT LED Vapor Tight Light Instruction Manual

1. Entwodiksyon

This manual provides detailed instructions for the safe installation, operation, and maintenance of your LEDONE 8FT LED Vapor Tight Light. Please read this manual thoroughly before installation and retain it for future reference. This fixture is designed for demanding environments requiring high resistance to water, dust, and corrosion, such as parking garages, car washes, cold storage, and industrial facilities.

2. Enfòmasyon sou Sekirite

AVÈTISMAN: Risk pou chòk elektrik. Dekonekte kouran an anvan enstalasyon oswa antretyen.

• Installation must be performed by a qualified electrician in accordance with the National Electrical Code (NEC) and local codes.
• Asire rezèv la voltage is compatible with the fixture's requirements (120-277Vac).
• Do not handle energized fixtures with wet hands or while standing on wet or damp sifas yo.
• Pa eseye modifye oswa demonte aparèy la. Pa gen okenn pyès ki ka repare pa itilizatè a anndan.
• Mete ekipman pwoteksyon pèsonèl (PPE) ki apwopriye pandan enstalasyon an.
• Asire w ke aparèy la byen monte pou anpeche l tonbe.

3. Pake kontni

Verifye ke tout konpozan yo prezan epi yo pa domaje anvan ou kontinye ak enstalasyon an.

• LEDONE 8FT LED Vapor Tight Light Fixture
• Mounting Hardware (clips, screws, anchors)
• Manyèl Enstriksyon (dokiman sa a)

4. Enstalasyon ak Enstalasyon

4.1. Pre-Enstalasyon

1. Fèmen pouvwa: Locate the circuit breaker or fuse box and turn off the power supply to the installation area. Verify power is off using a voltage tèsteur.
2. Dekonpoze: Carefully remove the fixture from its packaging. Inspect for any shipping damage.
3. Chwazi Wattage and Color Temperature (CCT): Before mounting, adjust the wattage and CCT switches located on the fixture. These switches allow you to select between 60W, 80W, or 100W and 3500K, 4000K, or 5000K. Make your selection based on your lighting requirements.

Image: Product dimensions and location of wattage/CCT selection switches.

4.2. Monte aparèy la

The fixture is designed for surface mounting. Use the provided mounting clips and hardware.

1. Mark the desired mounting locations on the ceiling or wall. Ensure the marks are level and spaced appropriately for the fixture's length.
2. Drill pilot holes at the marked locations. Insert wall anchors if mounting into drywall or masonry.
3. Secure the mounting clips to the surface using the provided screws.
4. Snap the LED vapor tight fixture into the mounted clips, ensuring it is firmly seated.

Imaj: Egzample of surface mounting in a facility.

Image: Detail of the linkable design feature.

4.3. Fil elektrik

This fixture supports 0-10V dimming. Follow the wiring diagram below and local electrical codes.

• Konekte a Nwa fil soti nan aparèy la rive nan la Liy (L) fil ki soti nan ekipman pou pouvwa a.
• Konekte a Blan fil soti nan aparèy la rive nan la net (N) fil ki soti nan ekipman pou pouvwa a.
• Konekte a Vèt fil soti nan aparèy la rive nan la Tè (GND) fil ki soti nan ekipman pou pouvwa a.
• Pou gradyasyon 0-10V: Konekte Koulè wouj violèt fil soti nan aparèy la rive nan la Dim+ wire from the 0-10V dimmer. Connect the Woz/gri fil soti nan aparèy la rive nan la Dim- wire from the 0-10V dimmer.
• Asire w tout koneksyon yo byen fèm lè w sèvi ak konektè fil ki apwopriye yo.

Note: If 0-10V dimming is not used, cap the purple and pink/gray wires individually with wire nuts.

5. Operasyon Enstriksyon

1. Pouvwa sou: Once installation and wiring are complete, restore power to the circuit at the breaker or fuse box. The fixture should illuminate.
2. Dimming: If connected to a compatible 0-10V dimmer, adjust the dimmer control to achieve the desired light output level.
3. Wattage and CCT Adjustment: Wattage and CCT are set via internal switches during installation. These are not typically adjusted during normal operation. If changes are needed, disconnect power before accessing the switches.

6. Antretyen

The LEDONE Vapor Tight Light is designed for long-term, low-maintenance operation. Regular cleaning can help maintain optimal light output.

• Netwayaj: Dekonekte kouran an anvan ou netwaye. Sèvi ak yon twal mou.amp cloth with a mild, non-abrasive cleaner to wipe the exterior of the fixture. Do not use harsh chemicals or abrasive pads, as these can damage the finish or lens.
• Enspeksyon: Periodically inspect the fixture and mounting hardware for any signs of damage, loose connections, or wear. Address any issues promptly.
• Pa gen okenn pati itilizatè yo ka fè sèvis: The LED light source and driver are integrated components. Do not attempt to open or repair the fixture. Contact qualified personnel for any issues beyond basic cleaning and inspection.

Image: The IP65 waterproof rating ensures durability in wet conditions.

NAN. Depanaj

Before performing any troubleshooting, ensure power is disconnected at the circuit breaker.

8. Espesifikasyon

Image: Key features and certifications of the LEDONE Vapor Tight Light.

9. Enfòmasyon sou Garanti

LEDONE products are manufactured to high quality standards. This product comes with a standard manufacturer's warranty. Please refer to the product packaging or the official LEDONE websit la pou tèm ak kondisyon espesifik garanti a. Kenbe prèv acha ou pou reklamasyon garanti.

10. Sipò pou Kliyan

If you have any questions, require technical assistance, or need to report an issue, please contact LEDONE customer support:

• Websit: Vizite magazen LEDONE sou Amazon (pou kesyon jeneral)
• Imèl: Gade anbalaj pwodwi a oswa enfòmasyon ofisyèl yo website for direct support email.
• Telefòn: Gade anbalaj pwodwi a oswa enfòmasyon ofisyèl yo website for direct support phone number.

Please have your product model number (8FT LED Vapor Tight Light) and proof of purchase ready when contacting support.