Mount-It! MI-766 Dual Monitor Wall Mount Instruction Manual

1. Entwodiksyon

This instruction manual provides comprehensive guidance for the safe and effective installation, operation, and maintenance of your Mount-It! MI-766 Dual Monitor Wall Mount. This mount is designed to support two monitors up to 27 inches each, featuring full motion articulation and a gas spring system for easy adjustments. Please read this manual thoroughly before installation and retain it for future reference.

2. Enfòmasyon sou Sekirite

AVÈTISMAN: Failure to read and follow all instructions may result in personal injury or property damage. The manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

• Ensure the mounting surface can safely support the combined weight of the mount and monitors.
• Pa depase kapasite pwa maksimòm lan ki se 14.4 liv (6.5 kg) pou chak bra.
• Pwodwi sa a fèt pou itilize andedan kay la sèlman.
• Use appropriate safety equipment and tools during installation.
• Si ou pa sèten sou nenpòt pati nan pwosesis enstalasyon an, konsilte yon pwofesyonèl ki kalifye.
• Kenbe timoun ak bèt kay lwen pandan enstalasyon an.

3. Pake kontni

Verify that all components are present and undamaged before beginning installation. If any parts are missing or damaged, contact Mount-It! customer service.

• Dual Monitor Wall Mount Assembly
• Plak VESA (2)
• Mounting Hardware Kit (screws, washers, anchors for various wall types)
• Hex Wrenches for adjustments
• Manyèl Enstriksyon

4. Enstalasyon ak Enstalasyon

Before installation, determine your wall type (wood stud, concrete, or brick) and ensure it can support the weight. A stud finder and level are recommended.

Figure 4.1: Mount-It! MI-766 Dual Monitor Wall Mount

4.1. Wood Stud Mounting

1. Locate the Stud: Use a stud finder to locate the center of a wood stud at your desired mounting height.
2. Make twou gid yo: Hold the wall mount against the wall, ensuring it is level. Mark the center of the mounting holes with a pencil.
3. Fè twou pilòt: Drill pilot holes using a 3/16 inch (4.5 mm) drill bit to a depth of 2.2 inches (55 mm).
4. Kole montaj la sou miray la: Secure the wall mount to the wall using the provided lag screws and washers. Tighten until secure, but do not overtighten.

4.2. Concrete or Brick Wall Mounting

1. Make twou gid yo: Hold the wall mount against the wall, ensuring it is level. Mark the center of the mounting holes with a pencil.
2. Fè twou pilòt: Drill pilot holes using a 3/8 inch (10 mm) drill bit to a depth of 2.4 inches (60 mm).
3. Mete lank: Insert the concrete anchors into the drilled pilot holes.
4. Kole montaj la sou miray la: Secure the wall mount to the wall using the provided lag screws and washers. Tighten until secure, but do not overtighten.

4.3. Attaching Monitors to VESA Plates

Figure 4.2: Detachable VESA Plate and Adjustment Ranges

1. Prepare Monitor: Place your monitor face down on a soft, clean surface. Select the appropriate size mounting bolts and washers for your monitor's VESA holes (75x75mm or 100x100mm).
2. Install Top Bolts: Install the top two bolts and washers into the monitor's VESA holes, leaving a gap of approximately 0.11 inches (3 mm) between the screw head and the monitor surface.
3. Pandye Monitè: Carefully hang the monitor onto the top of the VESA plate on the arm, ensuring the top bolts slide into the keyhole slots.
4. Install Lower Bolts: Install the lower two bolts and washers through the lower VESA holes and tighten all four bolts until secure. Do not overtighten.
5. Repeat for the second monitor.

4.4. Jesyon kab

To maintain a tidy workspace, route your monitor cables through the integrated cable management system.

1. Retire kouvèti: Use the provided hex wrench to remove the bolts securing the cable management covers on the underside of each arm. Gently pull the covers away.
2. Route Câbles: Route your monitor cables (power, video, etc.) along the arm channels.
3. Ranplase Kouvèti yo: Replace the covers and secure them with their bolts.

5. Operasyon ak Ajisteman

The Mount-It! MI-766 offers a range of adjustments to achieve optimal viewang ing ak pozisyon ergonomic.

Figure 5.1: Dual monitor setup with the MI-766 wall mount.

5.1. Ajisteman Tansyon Ressò Gaz

The gas spring system allows for effortless height adjustment. The tension needs to be calibrated to your monitor's weight.

Figure 5.2: Gas Spring Tension Adjustment points.

1. Access Tension Bolt: Position the monitor horizontally. Lift the arm slightly to access the tension adjustment bolt located on the arm.
2. Ajiste tansyon an: Use the provided hex wrench to adjust the tension:
   • Vire counter-clockwise (towards '+') for heavier monitors (to increase tension).
   • Vire clockwise (towards '-') for lighter monitors (to decrease tension).
3. Test Adjustment: Continue adjusting until the arm stays in place when you move the monitor to different heights.

5.2. Height, Swivel, Tilt, and Rotation

Figure 5.3: Gas Spring Hovering System allows for easy tilt adjustments.

• Ajisteman wotè: Once the gas spring tension is correctly set, you can raise or lower your monitors by hand to your desired ergonomic height.
• Swivel: The monitor arms can swivel up to 90 degrees left or right from the central mounting point, allowing for flexible positioning.
• Enklinezon: Monitors can be tilted from +90 degrees to -45 degrees to reduce glare and optimize viewing angles. If the monitor droops or won't hold its angle, tighten the side bolts on the VESA plate connection.
• Wotasyon: Each monitor can be rotated 360 degrees, allowing for landscape or portrait orientation.

Figure 5.4: Monitors can rotate 360 degrees for portrait or landscape viewing.

6. Antretyen

Antretyen regilye asire lonjevite ak fonksyònman an sekirite nan sipò monitè ou a.

• Netwayaj: Siye montaj la ak yon twal mou.amp twal. Evite pwodui netwayaj abrazif oswa solvan.
• Enspeksyon: Periodically check all screws and connections to ensure they are tight and secure. Re-tighten if necessary.
• Sous-gaz: If the gas spring tension feels off, re-adjust it according to the instructions in Section 5.1.

NAN. Depanaj

If you encounter issues with your Mount-It! MI-766, refer to the following common problems and solutions.

• Monitor is drooping or not holding its height:
  • The gas spring tension may be too low for your monitor's weight. Increase the gas spring tension (rotate counter-clockwise) as described in Section 5.1.
• Monitor is difficult to move or stays too high:
  • The gas spring tension may be too high for your monitor's weight. Decrease the gas spring tension (rotate clockwise) as described in Section 5.1.
• Monitor tilts unexpectedly or won't hold its tilt angle:
  • Tighten the side bolts on the VESA plate connection that control the tilt mechanism.
• Mount feels unstable on the wall:
  • Ensure all lag screws securing the mount to the wall are fully tightened. Re-check the wall type and ensure appropriate anchors/stud mounting was used. If unsure, consult a professional.

8. Espesifikasyon

Figure 8.1: Supported monitor size and weight capacity.

Figure 8.2: The mount is compatible with brick, concrete, and wood walls.

9. Garanti ak sipò

Mount-It! products are backed by a limited warranty. For specific warranty details, product support, or to purchase replacement parts, please visit the official Mount-It! websit oswa kontakte depatman sèvis kliyan yo.

Sipò sou entènèt: Visit the Mount-It! Store on Amazon