BONTEC Full Motion TV Wall Mount

1. Enfòmasyon enpòtan sou sekirite

Please read this entire instruction manual before beginning installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance. Keep this manual for future reference.

• Do not begin installation until you have read and understood all the instructions and warnings contained in this installation sheet.
• This product is designed to be installed on wood studs, solid concrete, or brick walls. Do not install this product on drywall alone.
• The wall mount is designed to hold TVs weighing up to 132 lbs (60 kg). Do not exceed this weight limit.
• Asire ke sifas sipò a ap sipòte pwa konbine ekipman an ak tout pyès ki nan konpitè ak konpozan ki tache.
• Toujou sèvi ak yon asistan oswa yon ekipman leve mekanik pou leve ak pozisyon ekipman san danje.
• Tighten screws firmly but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Pwodwi sa a fèt pou itilize andedan kay la sèlman.

Figure 1: Wall Compatibility and VESA Patterns. This mount supports VESA patterns from 200x100mm to 600x400mm and is suitable for 37-84 inch TVs. Always confirm wood stud spacing before purchase.

2. Pake kontni

Verify that you have all the components shown below. If any parts are missing or damaged, contact BONTEC customer service for a replacement.

Figure 2: All included hardware for assembly and mounting. This includes various screws, washers, spacers, concrete anchors, self-tapping screws, an HDMI cable, and cable ties.

• Pre-assembled TV Wall Mount Unit
• Complete set of Assembly Hardware (M6, M8 screws, plastic washers, steel washers, Allen key)
• Wall Anchors (Concrete Anchors, Self-tap Screws, Washers)
• TV Mounting Screws (M4, M6, M8 screws of various lengths, spacers, square washers)
• 1 x 71-inch HDMI Cable
• 5 x lyen kab

3. Setup (Installation Guide)

Follow these steps carefully for a secure and successful installation of your BONTEC TV Wall Mount. A video guide is also available for visual assistance.

Step 1: Assemble the TV Plate

Attach the two vertical arms to the central TV plate using the provided screws and Allen key. Ensure they are securely fastened.

Etap 2: Monte plak miray la

Determine your wall type (brick, concrete, or wood studs) and follow the appropriate instructions.

• For Brick or Concrete Walls:
  1. Position the wall plate on the desired location and mark the drill holes. Use a spirit level to ensure it's perfectly horizontal.
  2. Drill holes using a 0.4-inch (10mm) drill bit.
  3. Insert the concrete anchors into the drilled holes. Tap gently with a hammer if needed.
  4. Align the wall plate with the anchors and secure it using the appropriate screws and washers.
• Pou miray ak poto an bwa:
  1. Use a stud finder to locate the center of your wood studs. Mark the drill holes, ensuring they align with the wall plate's mounting holes and are level.
  2. Drill pilot holes using a 0.2-inch (5mm) drill bit.
  3. Align the wall plate with the pilot holes and secure it using the appropriate self-tapping screws and washers.

Step 3: Install VESA Plate to the back of TV

Attach the assembled TV plate (from Step 1) to the back of your TV. Select the correct screws and spacers that fit your TV's VESA mounting holes. For curved TVs, use the appropriate spacers to ensure a flat mounting surface.

Step 4: Final Installation - Hang your TV to the Brackets and Lock it

Carefully lift your TV with the attached TV plate and hook it onto the wall plate. Ensure the hooks are properly seated. Once hung, tighten the security screws located at the bottom of the TV plate to prevent accidental dislodging.

Etap 5: Ajisteman Nivo

After hanging the TV, you can make fine adjustments to ensure it is perfectly level. Use the built-in level adjustment screws on the TV plate to rotate the TV slightly left or right (±3° rotation adjustment).

Figure 3: Easy Installation. The mount is designed for quick setup, typically within 15 minutes.

4. Operasyon Enstriksyon

Your BONTEC Full Motion TV Wall Mount offers flexible viewang ing pou konfò optimal.

• Ajisteman enklinezon: The mount features a ±20° tilt capability. Loosen the tilt adjustment screws on the TV plate, adjust to your desired angle to reduce glare or improve viewing, and then re-tighten the screws.
• Ajisteman Swivel: The dual arms allow for a ±45° swivel. Gently push or pull the TV to the left or right to achieve your preferred viewpozisyon ing.
• Level Rotation: Fine-tune the horizontal level of your TV by rotating it ±3° using the level adjustment screws on the TV plate.
• Ekstansyon ak Retrè: The mount can extend up to 15.4 inches (390mm) from the wall and retract to a low profile of just 2.6 inches (65mm), saving valuable space.

Figure 4: Swivel Functionality. Adjust your TV up to ±45° for optimal viewsoti nan plizyè ang.

Figure 5: Tilt and Level Adjustment. Customize your viewing experience with ±20° tilt and ±3° level rotation.

Figure 6: Compatible Screen Sizes. The mount is compatible with 37-84 inch screens.

5. Antretyen

To ensure long-term performance and safety of your TV wall mount, regular maintenance is recommended:

• Check all screws and connections periodically (at least every three months) to ensure they remain tight.
• Clean the mount surface with a soft, damp twal. Evite itilize pwodui netwayaj abrazif oswa solvang.
• Ensure that no cables are pinched or damaged during movement of the TV. Use the provided cable ties for tidy management.

NAN. Depanaj

If you encounter any issues with your TV wall mount, refer to the following common problems and solutions:

• Televizyon an pa nivo: Use the level adjustment screws (Step 5 of Setup) to fine-tune the rotation. Ensure the wall plate was installed level initially.
• Difficulty moving the TV (swivel/tilt): Check if any screws on the articulating arms or tilt mechanism are overtightened. Loosen them slightly if necessary. Ensure cables are not obstructing movement.
• Mòn nan santi l enstab: Re-check all wall mounting screws and TV attachment screws to ensure they are securely tightened. Verify that the wall type is appropriate and that the mount is installed into studs or solid concrete/brick as per instructions. Do not exceed the maximum weight capacity of 132 lbs (60 kg).
• Pati ki manke: Refer to the Package Contents section. If any parts are missing, contact BONTEC customer service for assistance.

7. Espesifikasyon

8. Garanti & Sipò

BONTEC products are designed for long-term, low-maintenance use. For any product-related inquiries, technical support, or warranty claims, please contact BONTEC customer service.

• Plan Pwoteksyon: Additional protection plans are available for purchase, including a 3-Year Protection Plan and a Complete Protect plan. Please refer to your purchase details for more information.
• Kontakte: For support, please visit the official BONTEC store or contact their customer service channels as provided at the time of purchase.