1. Entwodiksyon
This manual provides essential information for the safe and efficient operation of your Jebao TSP 30,000 Liter Adjustable Pond Pump. The TSP series models feature a powerful motor with innovative electronics, offering up to 65% energy savings. This pump is designed for use in pond filter and circulation systems, capable of handling dirt particles up to 6 mm in size. Its wear-resistant ceramic shaft ensures extended service life.
2. Enstriksyon Sekirite
- Always disconnect the pump from the power supply before performing any maintenance, cleaning, or installation work.
- Ensure the power cable and plug are undamaged. Do not operate the pump if the cable or plug is compromised.
- The pump must be connected to a properly grounded electrical outlet.
- Do not lift or carry the pump by its power cable.
- Ensure the pump is installed in a stable position, either submerged or in a dry, protected area below water level.
- Keep children and pets away from the pond area during pump operation and maintenance.
- The pump is designed for water use only. Do not use it for other liquids.
3. Pake kontni
Tanpri verifye ke tout atik yo prezan nan pakè a:
- Jebao TSP Pond Pump
- Connection fittings (50 mm)
- Kab pouvwa (10 m)
- Manyèl itilizatè
4. Enstalasyon ak Enstalasyon
The Jebao TSP pump is suitable for both submersible and dry installation. For dry installation, the pump is not self-priming and must be installed below the water level to ensure proper water flow to the pump inlet.
4.1. Submersible Installation
- Place the pump horizontally on a stable, flat surface at the bottom of the pond.
- Ensure the pump is fully submerged and free from obstructions.
- Connect the outlet hose (50 mm) to the pump's discharge port. Secure with a hose clamp si sa nesesè.
4.2. Dry Installation
- Install the pump in a dry, well-ventilated area, protected from direct sunlight and frost.
- The pump must be positioned below the water level of the pond to allow gravity-fed water supply.
- Connect the inlet hose (50 mm) from the pond to the pump's inlet port. Ensure a watertight seal.
- Connect the outlet hose (50 mm) to the pump's discharge port. Secure all connections.
4.3. Koneksyon elektrik
After installation, connect the 10-meter power cable to a suitable, grounded electrical outlet. Ensure the outlet is protected by a Residual Current Device (RCD) for safety.

Figi 1: Prensipal view of the Jebao TSP Pond Pump.

Figure 2: Technical diagram showing the dimensions of the Jebao TSP Pond Pump (188 x 104 x 128 mm).
5. Operasyon Enstriksyon
Once the pump is correctly installed and connected to the power supply, it will begin operation. The TSP series pumps feature adjustable power consumption from 52 to 290 watts, allowing you to optimize flow rate and energy usage. Refer to any external controller provided with your pump for specific adjustment instructions.
5.1. Motor Protection
The pump is equipped with an electronic recognition IC that provides automatic 'dry-run' motor protection. If the rotor is blocked or the pump runs without water, the motor will automatically shut off to prevent damage. Disconnect power, inspect for blockages or lack of water, and then reconnect power to reset.

Figure 3: Performance curve illustrating flow rate (L/H) versus head height (M) for the Jebao TSP pump at different settings (e.g., 25000 L/H and 30000 L/H).
6. Antretyen
Antretyen regilye asire pèfòmans optimal epi pwolonje dire lavi ponp ou a.
6.1. Cleaning the Impeller
- Dekonekte ponp lan soti nan ekipman pou pouvwa a.
- Remove the pump from the pond or disconnect it from the dry installation system.
- Carefully open the pump housing to access the impeller chamber.
- Remove any debris, algae, or blockages from the impeller and its chamber. A soft brush can be used.
- Enspekte aks seramik la pou wè si li pa mete oswa domaje.
- Reassemble the pump, ensuring all seals are correctly seated.
6.2. Netwayaj jeneral
Periodically clean the exterior of the pump to prevent buildup of algae or mineral deposits. Use fresh water and a soft cloth. Do not use harsh chemicals or abrasive materials.
NAN. Depanaj
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Ponp pa kòmanse | Pa gen ekipman pou pouvwa Impeller bloke Dry-run protection activated | Check power connection and RCD Clean impeller (see Section 6.1) Ensure pump is submerged or receiving water, then reconnect power |
| Redwi pousantaj koule | Inlet/outlet blocked Impeller dirty Pump operating at low power setting | Check and clear blockages in hoses/fittings Clean impeller (see Section 6.1) Adjust power setting (if applicable) |
| Ponp fè bri dwòl | Debri nan roue Worn impeller or shaft | Clean impeller (see Section 6.1) Kontakte sipò kliyan pou pati ranplasman |
8. Espesifikasyon
| Karakteristik | Spesifikasyon |
|---|---|
| Modèl | TSP |
| Konsomasyon pouvwa | 52 - 290 wat |
| Pousantaj maksimòm koule | 30,000 lit pou chak èdtan |
| Maksimòm wotè tèt | 5 mèt |
| Gwosè Koneksyon | 50 mm |
| Longè kab | 10 mèt |
| Dimansyon (L x W x H) | 188 x 104 x 128 mm |
| Max. Debris Particle Size | 6 mm |
| Sous Enèji | Fil elektrik |
| Manifakti | JEBAO |
| Premye Dat ki disponib | 21 fevriye 2020 |
9. Garanti ak sipò
This product comes with an Italian warranty. For warranty claims, technical support, or replacement parts, please contact your retailer or the official Jebao distributor in your region. Ensure you have your proof of purchase and product model information available when contacting support.