XP POWER HPU1K5PS48 AC-DC Power Supply

1. Entwodiksyon

This manual provides essential information for the safe and effective installation, operation, and maintenance of the XP POWER HPU1K5PS48 AC-DC Power Supply. Please read this manual thoroughly before attempting to install or operate the unit. Retain this manual for future reference.

2. Enfòmasyon sou Sekirite

AVÈTISMAN: Risk of electric shock. This unit contains hazardous voltages. Only qualified personnel should perform installation and servicing.

• Ensure the power supply is disconnected from the AC mains before any installation, wiring, or maintenance procedures.
• Verifye ke D' voltage range (85-264VAC) matches the local mains supply.
• Proper grounding is essential to prevent electric shock. Connect the protective earth terminal to a reliable ground.
• Do not operate the unit in environments with excessive moisture, dust, or corrosive gases.
• Asire w ke gen ase vantilasyon toutotou ekipman pou pouvwa a pou anpeche li chofe twòp.
• Pa louvri fil kouran an casing. Pa gen okenn pyès itilizatè a ka repare anndan an.

3. Pwodwi souview

The XP POWER HPU1K5PS48 is a high-power, enclosed AC-DC power supply designed for panel mounting. It provides a regulated 48V DC output with an auxiliary 5V 1A output. Key features include:

• Antre Voltage: 85-264VAC
• Main Sòti: 48V DC, 25A (for <180VAC input) / 31A (for >180VAC input)
• Sòti oksilyè: 5V DC, 1A
• Total pouvwa: 1493W
• Faktè fòm: Enclosed, Panel Mount
• Pèsistans yap ogmante jiska Voltage

4. Enstalasyon

4.1. Debalaj ak Enspeksyon

Carefully unpack the power supply and inspect it for any signs of physical damage. If damage is found, do not proceed with installation and contact your supplier.

4.2. Monte

The HPU1K5PS48 is designed for panel mounting. Ensure the mounting surface is stable and capable of supporting the unit's weight. Maintain adequate clearance around the unit for proper airflow and heat dissipation. Refer to the product datasheet for specific mounting dimensions and recommended clearances.

4.3. Koneksyon fil elektrik

All wiring should be performed by qualified personnel in accordance with local electrical codes and regulations. Use appropriate gauge wiring for the input and output currents.

1. Antre AC: Connect the AC mains supply to the designated input terminals (L, N, PE). Ensure correct polarity and a secure protective earth connection.
2. DC Sòti: Connect the load to the DC output terminals (+V, -V). Observe correct polarity.
3. Sòti oksilyè: If required, connect the auxiliary load to the 5V 1A output terminals.
4. Remote Sense (if applicable): Pou aplikasyon ki mande volim egzaktage regulation at the load, connect the remote sense terminals (+S, -S) to the load's positive and negative terminals, respectively. Ensure sense lines are twisted and shielded if necessary.
5. Remote On/Off (if applicable): Connect remote control signals to the designated terminals as per the product datasheet.

4.4. Sòti Voltage Ajisteman

Pwodiksyon prensipal la voltage can be adjusted using the potentiometer located on the unit. Use a non-conductive tool to carefully turn the potentiometer to achieve the desired output voltage within the specified adjustment range. Monitor the output voltage avèk yon miltimèt pandan ajisteman.

5. Operasyon Enstriksyon

After completing the setup and verifying all connections, the power supply is ready for operation.

1. Pouvwa sou: Apply AC mains power to the unit. The power supply should initiate and provide the regulated DC output voltage.
2. Koneksyon chaj: Connect the load to the DC output. Ensure the load current does not exceed the maximum rated output current of the power supply.
3. Siveyans: Kontwole volim pwodiksyon an regilyèmantage and current to ensure stable operation.
4. Pouvwa Off: To shut down the unit, disconnect the AC mains power.

6. Antretyen

The XP POWER HPU1K5PS48 power supply is designed for reliable operation with minimal maintenance. However, periodic inspection is recommended.

• Netwayaj: Ensure the ventilation openings are free from dust and debris. If cleaning is necessary, disconnect the unit from the AC mains and use a soft, dry cloth. Do not use liquid cleaners.
• Koneksyon: Periodically check all input and output connections for tightness and signs of corrosion.
• Kondisyon anviwònman: Asire w ke anviwònman operasyon an rete nan limit tanperati ak imidite espesifye yo.

Nòt: There are no user-serviceable parts inside the power supply. Any internal servicing must be performed by XP POWER authorized service personnel.

NAN. Depanaj

If the power supply is not operating as expected, perform the following basic checks:

If the problem persists after performing these checks, contact XP POWER technical support.

8. Espesifikasyon

9. Garanti ak sipò

For warranty information, technical support, or service inquiries, please contact XP POWER directly or your authorized distributor. Refer to the official XP POWER websit la pou jwenn enfòmasyon kontak ak kondisyon garanti ki pi resan yo.

XP POWER Contact Information: www.xppower.com/contact