Everbilt 1/2 HP Submersible Aluminum Sump Pump with Tethered Switch User Manual

Entwodiksyon

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Everbilt 1/2 HP Submersible Aluminum Sump Pump. Please read all instructions carefully before use to ensure proper function and to prevent injury or damage.

Enfòmasyon sou Sekirite

AVÈTISMAN: Always disconnect power before servicing or performing any maintenance on the pump.

DANJE: Risk chòk elektrik. Ponp sa a apwovizyone ak yon kondiktè tè ak ploge atachman ki kalite tè. Pou diminye risk pou chòk elektrik, asire w ke li konekte sèlman ak yon resipyan ki byen chita ak tè.

• Pa sèvi ak ponp lan si kòd kouran an oswa ploge a domaje.
• Asire w ke ponp lan mete sou yon sifas ki estab ak nivo.
• Do not pump flammable or corrosive liquids.
• Kenbe timoun ak bèt kay lwen ponp ki ap fonksyone a.
• Wear appropriate personal protective equipment (PPE) when handling the pump.
• This pump is designed for clear water only.

Pwodwi souview

The Everbilt 1/2 HP Submersible Sump Pump is designed for efficient water removal from sump basins. It features an aluminum motor housing for effective cooling and a tethered float switch for automatic operation.

Figi 1: Everbilt 1/2 HP Submersible Aluminum Sump Pump. This image shows the black pump unit with its tethered float switch, power cord, and 1-1/2 inch FNPT discharge port. The Everbilt logo is visible on the side of the pump body.

Karakteristik kle:

• Aluminum motor housing for efficient motor cooling.
• Continuous duty, efficient 115-Volt PSC motor for lower carbon footprint; higher efficiency using less energy to operate.
• 8.25 ft. cord length.
• Submersible for quiet operation.
• 1-1/2 in. FNPT discharge.
• Semi-open thermoplastic impeller passes 3/8 in. solids.
• Pwoteksyon Surcharge tèmik.

Enstalasyon ak Enstalasyon

1. Pwizon Basin Preparasyon: Ensure your sump basin has a minimum diameter of 18 inches to accommodate the tethered float switch. Clean the basin of any debris or obstructions.
2. Plasman: Place the pump on a solid, level surface at the bottom of the sump basin. Ensure the pump is stable and will not tip over during operation.
3. Koneksyon Tiyo Egzeyat: Connect a 1-1/2 inch FNPT (Female National Pipe Thread) discharge pipe to the pump's outlet. It is recommended to use a check valve in the discharge line to prevent water from flowing back into the sump basin when the pump turns off.
4. Ajisteman switch flote: The tethered float switch controls the pump's on/off cycles. Adjust the tether length to set the desired "on" and "off" water levels. Ensure the float can move freely without obstruction within the sump basin. The switch-on height is approximately 11.81 inches and switch-off height is approximately 3.94 inches, but can be adjusted by tether length.
5. Koneksyon pouvwa: Plug the pump's 8.25 ft. power cord into a properly grounded 115-Volt AC outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety.
6. Operasyon tès: Fill the sump basin with water to activate the float switch and ensure the pump turns on and discharges water correctly. Allow the water level to drop to verify the pump turns off automatically.

Enstriksyon Operasyon

The Everbilt 1/2 HP Submersible Sump Pump operates automatically via its tethered float switch. Once properly installed and connected to power, the pump will activate when the water level rises to the "on" point and deactivate when the water level drops to the "off" point.

• Operasyon otomatik: The pump is designed for continuous duty and will cycle on and off as needed based on the water level in the sump basin.
• Sispansyon manyèl (si sa aplikab): While primarily automatic, some installations may allow for manual operation by lifting the float switch. Refer to your specific setup for manual control options.
• Siveyans: Tcheke puisar b la detanzantan.asin and pump operation, especially during heavy rainfall, to ensure it is functioning correctly.

Antretyen

Regular maintenance ensures the longevity and reliable operation of your sump pump.

1. Dekonekte pouvwa: Always disconnect the pump from the power source before performing any maintenance.
2. Netwaye puisard Basin: Periodically remove any debris, dirt, or sediment from the sump basin that could interfere with pump operation or float switch movement.
3. Enspekte Enpèlè a: Check the pump's impeller for any clogs or damage. The semi-open thermoplastic impeller is designed to pass 3/8 inch solids, but larger debris can cause issues.
4. Tcheke switch flote a: Ensure the tethered float switch moves freely and is not obstructed by wires, pipes, or debris.
5. Enspekte fil elektrik: Examine the power cord for any signs of wear, cuts, or damage. Replace if necessary.
6. Winterization (si sa aplikab): If the pump is in an area subject to freezing temperatures and will not be used, remove it from the basin, clean it, and store it in a dry, warm place.

Depanaj

If problems persist after attempting these solutions, please contact Everbilt customer support.

Espesifikasyon

Garanti ak sipò

For warranty information or technical support, please contact Everbilt customer service. Keep your purchase receipt as proof of purchase for any warranty claims.

Pou plis asistans, ou ka vizite Everbilt brand page on Amazon or consult the retailer where the product was purchased.